SyncMaster 320P
Model Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Ground to prevent an electric shock Power When not used for an extended period of time, set your computer to DPMS. If using a screen saver, set it to active screen mode. Do not use a damaged or loose plug.
z This may cause electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. z This may cause electric shock or fire. Use only a properly grounded plug and receptacle. z An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. z A bad connection may cause fire. Do not bend the plug excessively and wire nor place heavy objects upon them, which could cause damage.
location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc. Failure to do so may cause serious damage to your monitor. Place your monitor in a location with low humidity and a minimum of dust. z Failure to do so may cause electric shock or fire inside the monitor. Do not drop the monitor when moving it. z This may cause damage to the product or the person carrying it.
z Failing to do so may damage the monitor. Do not place the monitor face down. z This may damage the TFT-LCD surface. The installation of the bracket must be done by a qualified professional. z z Installing the bracket by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. When installing the product, make sure to keep it away from the wall (more than 10 cm/4 inches) for ventilation purposes.
z A dirty connector may cause electric shock or fire. Make sure to unplug the power cord before cleaning the product. z Otherwise, this may cause electric shock or fire. Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. z Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent. Contact the SAMSUNG customer care center or Customer Center for interior cleaning once a year.
Disconnect the plug from the outlet during storms or lightning or if it is not used for a long period of time. z Failure to do so may cause electric shock or fire. Do not try to move the monitor by pulling only the wire or the signal cable. z This may cause a breakdown, electric shock or fire due to damage to the cable. Do not move the monitor right or left by pulling only the wire or the signal cable. z This may cause a breakdown, electric shock or fire due to damage to the cable.
Adjust the resolution and frequency to the level appropriate for the model. z An inappropriate resolution may cause undesirable picture quality. 32 inch (80 cm) - 1360 X 768 Viewing the monitor continuously at a too close angle may result in damage to your eyesight. To ease eye strain, take at least a five-minute break after every hour of using the monitor. Do not install the product on an unstable, uneven surface or a location prone to vibrations.
do not swallow the batteries. Keep the batteries out of children's reach. z If the batteries are swallowed, see a doctor immediately. When replacing batteries, place the batteries in the correct +/- polarity position as indicated on the battery holder. z The incorrect polarity may cause a battery to break or leak and may cause fire, injury, or contamination (damage). Use only specified standard batteries. Do not use new and used batteries together.
Model Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. This stand is not for the Floor Standing Type.
D-Sub Cable Power Cord Speaker Wire Cable Wall Mount KIT Speaker Set Stand KIT Remote Control Batteries (AAA X 2) Cover-Hole BNC to RCA Adapter Jack Semi Stand Sold separately DVI Cable Other
Front 1. MENU 6. PIP 2. Navigate buttons (Up-Down buttons) 7. Power button 3. Adjust buttons (Left-Right buttons)/ Volume buttons 8. Power indicator 4. ENTER 9. Remote Control Sensor 5. SOURCE 1. MENU Opens the on-screen menu and exits from the menu or closes the screen adjustment menu. 2. Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values. 3.
for long periods. Rear For detailed information concerning cable connections, refer to Connecting Cables under Setup. The monitor's configuration at the back may vary slightly depending on the monitor model. 1. RS232C OUT/IN (RS232C Serial PORT): MDC(Multiple Display Control) Program Port 2. DVI IN(HDCP) (PC Video Connection Terminal) : Using a DVI Cable (DVI-D to DVI-D) - DVI mode (Digital PC) 3. PC IN(RGB) (PC Video Connection Terminal) : Using a D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC) 4.
5. COMPONENT AUDIO IN [L-AUDIO-R](Component Audio Connection Terminal (Input)) 6. BNC/COMPONENT OUT (BNC/Component Connection Terminal (Output)) - BNC (Analog PC) Connection : connecting the R, G, H, V ports. - Component Connection : connecting the PR, Y, PB ports 7. BNC/COMPONENT IN (BNC/Component Connection Terminal (Input)) 8. AV AUDIO IN [L-AUDIO-R](Monitor Audio Connection Terminal (Input)) 9. AV OUT [VIDEO](VIDEO Connection Terminal) : AV mode (Output) 10.
The Kensington lock is a device used to physically fix the system to something when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact the place of purchase. See Connecting the Monitor for further information regarding cable connections. Remote Control The performance of the remote control may be affected by a TV or other electronic device operating near the monitor, causing a malfunction due to interference with the frequency. 1.
1. ON / OFF Turns the monitor On/Off. 2. MAGICNET MagicNet Quick Launch Button. - This fuction does not work for this monitor. 3. MDC MDC Quick Launch Button. 4. LOCK Activates or deactivates all function keys on both the remote control and the monitor except for the Power and LOCK buttons. 5. MagicNet buttons - Used for MagicNet. z z z z Alphanumeric: Used to enter the Internet address. DEL : Functions as the backspace. SYMBOL: Used to enter the symbols (.O_-:/). ENTER : Used to enter values.
The current picture information is displayed in the top left corner of the screen. 16. EXIT Exits from the menu screen. 17. Up-Down Left-Right buttons Moves from one menu item to another horizontally, vertically or adjusts selected menu values. 18. P.MODE (M/B) When pressing this button, current picture mode is displayed at the bottom center of the screen. AV / S-Video / Component : P.MODE The Monitor has four automatic picture settings that are preset at the factory.
Mechanical Layout | Monitor Head | Stand | Speaker | Installation VESA Bracket | Wall Bracket Installation 1. Mechanical Layout 2.
3. Stand 4. Speaker 5. Installation VESA Bracket z z z z When installing VESA, make sure to comply with the international VESA standards. Purchasing VESA Bracket and Installation Information : Please contact your nearest Samsung Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. At least 2 persons are needed in order to move the LCD Monitor.
For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length. 6. Wall Bracket Installation z z z Contact a technician for installing the wall bracket. Samsung Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
3 1. Insert three Hangers of the set-bracket B into the grooves of the wall-bracket A. 2. Fix set-bracket B and wall-bracket A with screws D. Before installing the set on the wall, connect the cables to the set first.
Model Installing the Stand Kit Only the supplied bolts should be used. Samsung Electronics will not be responsible for damages caused by using a base other than those specified. 1. Installing the Semi Stand Left stand Right stand Make sure to install the stand with the Caution label folded backwards. 1. A 'Cover-Protector' is used to protect the hole at the bottom of the monitor, where the stand is inserted.
3. Insert the stand into the hole at the bottom of the monitor. Insert the screw into the hole indicated and tighten it. (M4 × L15) This stand is designed for adjusting the screen angle. The company is not responsible for any problem caused when using this stand. Under no circumstances use the product as a stand for placing something on. 2. Installing the Stand Kit (sold separately) 1. A 'Cover-Protector' is used to protect the hole at the bottom of the monitor, where the stand is inserted.
Connecting to a Computer | Connecting to a VCR | Connecting to a DVD Player | Connecting to a Camcorder Connecting to a DTV Set Top Box | Connecting Speakers | Connecting to an Audio System 1. Connecting to a Computer 1. Connect the power cord for your monitor to the power port on the back of the monitor. Trun on the power switch. 2. There are 3 ways to connect the signal cable to your monitor. Choose one of the following: 2-1. Using the D-sub (Analog) connector on the video card.
The The DVI cable or BNC cable is optional. 3. Connect the audio cable for your monitor to the audio port on the back of your computer. 4. Turn on both your computer and the monitor. Contact a local Samsung Electronics Service Center to buy optional items. 2. Connecting to a VCR 1. AV input devices such as VCRs or Camcorders are connected via the AV IN [VIDEO] or AV IN [SVIDEO] of the monitor using an S-VHS or BNC cable. The S-VHS or BNC cable is optional. 2.
1. Connect a set of audio cables between the COMPONENT AUDIO IN [L-AUDIO-R] on the Monitor and the AUDIO OUT jacks on the DVD player. 2. Connect a Component cable between the BNC/COMPONENT IN - P R, Y, PB port on the Monitor and the PR, Y, PB jacks on the DVD player. A component cable is optional. 3. Select Component for the connection to a DVD player using the Source button on the front of the monitor or on the remote control. 4. Then, start the DVD Player with a DVD disc inserted.
1. Connect a set of audio cables between the COMPONENT AUDIO IN [L-AUDIO-R] on the Monitor and the AUDIO OUT jacks on the Set Top Box. 2. Connect a Component cable between the BNC/COMPONENT IN - PR, Y, PB port on the Monitor and the PR, Y, PB jacks on the Set Top Box. 3. Select Component for the connection to a DTV Set Top Box using the Source button on the front of the monitor or on the remote control. For an explanation of Component video, see your Set Top Box owner's manual. 6. Connecting Speakers 1.
7. Connecting to an Audio System 1. Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and MONITOR OUT [L-AUDIO-R] on Monitor. 1. Introduction 2. Beginning : Main Screen | Port Selection | 3. Power Control 4. Input Source Control 5. Image Size Control : PC, BNC, DVI | AV, S-Video, Component, DVI(HDCP) 1. Introduction 6. Time Control 7. PIP Control : PIP Size | PIP Source 8. Settings Control : Picture | Picture PC | Audio | Image Lock | 9. Maintenance Control - Lamp Control 10.
A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously operated on a PC. RS-232C, a standard of serial communication, is used for communicating between a PC and a display. Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a display. 2. Main Screen Click Start > Program > Multiple Display Control to start the program. Select a set to see the volume of the selected set within the slider.
Main Icons Select Button Remocon Info Grid Safety Lock Display Selection Port Selection Control Tools 1. Use the main icons to switch to each screen. 2. Enables/Disables the remote control signal receiving function of the display unit. 3. The setting for the PC Serial Port can be changed. The original value is COM1. 4. Sets the Lock Function. 5. Click Select all or Clear to select or clear all displays. 6. Use Grid to view brief information on the selected display. 7.
1. Multiple Display Control is originally set to COM1. 2. If any port other than COM1 is used, COM1 to COM4 can be selected in the Port Selection Menu. 3. If the exact port name which is connected to the monitor using a serial cable is not selected, communication will not be unavailable. 4. The selected port is stored in the program and is used for the next program as well. 3. Power Control 1. Click on Power Control from the main icons and the Power Control screen appears.
Power Control allows the controlling of some of the functions of the selected display. 1) Power On/Off - Turns the power of the selected display On/Off. 2) Volume Control - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (When canceling the selection or choosing Select All, the value returns to the default value 10) 3) Mute On/Off - Enables/disables the Mute function of the selected display.
- Changes the Input Source of the selected display to DVI. 4) AV - Changes the Input Source of the selected display to AV. 5) S-Video - Changes the Input Source of the selected display to S-Video. 6) Component - Changes the Input Source of the selected display to Component. 7) MagicNet - The Input source of MagicNet works only for the MagicNet model. The Input Source Control feature is only available for the displays where the power is ON. 5. Image Size Control - PC, BNC, DVI 1.
The Info Grid shows some basic information necessary for the Image Size Control. 1) Click the AV, S-Video, Component tab to adjust Image Size for AV, S-Video, Component. Click Select All or use the Check Box to select a display to control. 2) The Info Grid only shows the display with AV, S-Video, Component or DVI(HDCP) as the input source. 3) Switches the Image Size of the selected display randomly.
The Input source of MagicNet works only for the MagicNet model. 7. PIP Control - PIP Size 1. Click on PIP from the main icons and the PIP Control screen appears. Click Select All or use the Check Box to select a display to control. The Info Grid shows some basic information necessary for the PIP Size Control. 1) PIP Size - Shows the current PIP Size of the display in use. 2) OFF - Turns off the PIP of the selected display. 3) Large - Turns on the PIP of the selected display and changes the size to Large.
The Info Grid shows some basic information necessary for the PIP Source Control. 1) PIP Source - The PIP Source can be controlled by turning on the monitor power. 2) PC - Changes the source of the PIP of the selected display to PC. 3) BNC - Changes the source of the PIP of the selected display to BNC. 4) DVI - Changes the source of the PIP of the selected display to DVI. 5) AV - Changes the source of the PIP of the selected display to AV.
The info Grid shows some basic information necessary for the Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When Select All is selected, the default value (50) is returned. Changing a value in this screen automatically changes the mode to "CUSTOM." 1) Picture - Available only for AV, S-Video, Component, DVI(HDCP). 2) Contrast - Adjusts the Contrast of the selected display. 3) Brightness - Adjusts the Brightness of the selected display.
The info Grid shows some basic information necessary for the Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When Select All is selected, the default value (50) is returned. Changing a value in this screen automatically changes the mode to "CUSTOM." 1) Picture PC - Available only for PC, BNC, DVI. 2) Contrast - Adjusts the Contrast of the selected display. 3) Brightness - Adjusts the Brightness of the selected display.
When Select All is selected, the default value (50) is returned. Changing a value in this screen automatically changes the mode to "CUSTOM." 1) Audio - Controls the audio settings for all input sources. 2) Bass - Adjusts the Bass of the selected display. 3) Treble - Adjusts the Treble of the selected display. 4) Balance - Adjusts the Balance of the selected display. 5) Dolby Virtual - Switches the Dolby Sound On/Off for the selected display. 6) BBE - BBE Sound On/Off for the selected display.
An "Info Grid" showing several basic data items appears. 1) Maintenance - Allows Maintenance Control for all input sources. 2) Auto Lamp Control Automatically adjusts the backlight of the selected display at a specified time. The Auto Lamp Control automatically turns off if you adjust using the Manual Lamp Control. 3) Manual Lamp Control - Allows you to adjust the backlight of the selected display regardless of the time.
1. Click on Maintenance from the main icons and the Maintenance Control screen appears. 1) Video Wall - A Video Wall is a set of video screens that are connected together, so that each screen shows a part of the whole picture or where the same picture is repeated on each screen. 2) Screen Divider - The screen can be divided into several images. A number of screens can be selected with a different layout when dividing. Select a mode in Screen Divider. Select a display in Display Selection.
The Maintenance Control function is only available for displays where the power is ON. The Input source of MagicNet works only for the MagicNet model. 12. Troubleshooting 1. The display you wish to control does not appear in the Power Control Info Grid. - Check the RS232C connection. (Check if it is properly connected to the Com1 port) - Check the displays to see if any of the other displays connected have the same ID.
One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor. The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute (ETRI).
Model Input Available Modes OSD Source List : PC / BNC / DVI : AV : S-Video Description Use to select PC, BNC or other external input sources connected to the Monitor. Use to select the screen of your choice. - The direct button on the remote control is the 'SOURCE' button. PIP turns off when the monitor is switched to an external source.
Video signal. (Off/On) More than one PIP cannot be overlapped on screen as BNC and the component use the same terminal. 1) PIP - The direct button on the remote control is 'PIP' button. Off On : Turns the PIP Screen Off/On. 2) Source - The direct button on the remote control is the 'SOURCE' button. PC / DVI : AV / S-Video / Component Mode BNC : AV / S-Video Mode AV / S-Video : PC / BNC / DVI Mode Component : PC / DVI Mode : Selects the input source for the PIP.
Available Modes OSD : PC / BNC / DVI : AV : S-Video Description MagicBright™ : Component Play MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Entertain, Internet,Text and Custom. Each mode has its own pre-configured brightness value. You can easily select one of the four settings by simply pressing the MagicBright™ control button.
1) Red 2) Green 3) Blue If you adjust picture using Color Control function, Color Tone will turn to Custom mode. Image Lock Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitters and shakiness. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again. - Available in PC/BNC Mode Only 1) Coarse : Removes noise such as vertical stripes. Coarse adjustment may move the screen image area.
Available Modes OSD : PC / BNC / DVI : AV : S-Video Description Mode The Monitor has four automatic picture settings ("Dynamic", "Standard", "Movie" and "Custom") that are preset at the factory. Dynamic, Standard, Movie, or Custom can be activated. - The direct button on the remote control is the P.MODE' button. 1) Dynamic 2) Standard 3) Movie 4) Custom Custom You can use the on-screen menus to change the contrast and brightness according to personal preferences. 1) Contrast : Adjusts the Contrast.
Off On Film Mode Turns Film Mode Off/On. The Film Mode feature offers you a theater-quality viewing experience. Off On DNIe Demo - Digital Natural Image engine Samsung's new technology brings you more detailed images with contrast and white enhancement and 3D noise reduction. A New image compensation algorithm gives brighter, clearer images to our customers. DNIe technology will match every signal to your eyes. You can compare a screen with DNle to that without DNle.
OSD Description Mode The Monitor has a built-in high fidelity stereo amplifier. 1) Standard : Selects Standard for the standard factory settings. 2) Music : Selects Music when watching music videos or concerts. 3) Movie : Selects Movie when viewing movies. 4) Speech : Selects Speech when watching a show that is mostly dialogue (i.e., news). 5) Custom : Selects Custom if you want to adjust the settings according to your personal preferences.
Available Modes OSD Time : PC / BNC / DVI : AV : S-Video : Component Description Selects from one of 4 time settings, Clock Set, Sleep Timer, On Timer, and Off Timer. 1) Clock Set : Current Time Setting. 2) Sleep Timer : Turns the Monitor off automatically at certain times. (Off, 30, 60, 90, 120, 150, 180) 3) On Timer : Turns the Monitor on automatically at a preset time. Controls the mode and the volume level at the time the monitor turns on automatically.
Video Wall A Video Wall is a set of video screens connected together, so that each screen shows a part of the whole picture or where the same picture is repeated on each screen. 1) Video Wall : Turns Off/On the Video Wall function of the selected display Off/On. Off On 2) Format : The format can be selected to see a divided screen. Full Provides a full screen without any margins. Natural Displays a natural image with the original aspect ratio intact.
(1~5 Seconds) By default, the time is set to 5 seconds. 1~5 Seconds Multi Control Available Modes OSD Multi Control : PC / BNC / DVI : AV : S-Video Description Assigns an individual ID to the SET. 1) ID Setup : Assigns distinctive IDs to the SET. 2) ID Input : Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to the transmitter setting becomes activated.
Available Modes OSD : PC / BNC / DVI : AV : S-Video Description MDC Moves to the Multi Control OSD screen. LOCK Sets the Safety Lock function. 1) Lock On : It will be locked. 2) Lock Off : It wil be unlocked. When setting the Lock function, you can only operate the power and lock buttons on the remote control and set. The preset password on the monitor is "0000".
Model Self-Test Feature Check Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check | Not Optimum Mode | Maintenance and Cleaning | Symptoms & Recommended Actions 1. Self-Test Feature Check Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. 1. Turn off both your computer and the monitor. 2.
Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the monitor. 3. Maintenance and Cleaning 1. Maintaining the Monitor Case. Clean with a soft cloth after disconnecting the power cord. z z Do not use benzene, thinner or other flammable substances, or a wet cloth. We recommend that a Samsung cleansing agent is used to prevent damage to the screen. 2. Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly.
Problems Solutions Screen is blank and power indicator is off z Ensure that the power cord is firmly connected and the LCD monitor is on. (Refer to the Connecting the Monitor) "Check Signal Cable" message z Ensure that the signal cable is firmly connected to the PC or video sources. (Refer to the Connecting the Monitor) Ensure that the PC or video sources are turned on. z "Not Optimum Mode " message z z Check the maximum resolution and the frequency of the video adapter.
z Sound is too high pitched or too low pitched z If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program. Adjust the Treble and Bass to the appropriate levels. 4. Problems related to the Remote Control Problems related to the remote control and their solutions are listed. Problems Items to check The remote control buttons do not respond. z z z z z Check the polarities (+/-) of the batteries.
Model SyncMaster 320P General General Model Name SyncMaster 320P LCD Panel Size 32 " Diagonal (80 cm) Display area 697.685 mm (H) x 392.256 Mm (V) Pixel Pitch 0.511mm (H) x 0.511mm (V) Synchronization Horizontal 30 ~ 70 kHz Vertical 50 ~ 85 Hz Display Color 16.7 M Colors Resolution Optimum resolution 1360 x 768 / 1366 x 768 @ 60 Hz depends on graphics card used Maximum resolution 1366 x 768 @ 60 Hz Input Signal, Terminated RGB Analog , DVI(Digital Visual Interface) Compliant Digital RGB.
Less than 5 W Dimensions (WxHxD)/ Weight 780 780 982 982 X 482 X X 530 X X 482 X X 530 X 107 223 107 223 mm / 30.1 mm / 30.1 mm / 38.7 mm / 38.7 X 19.0 X 20.9 X 19.0 X 20.9 X X X X 4.6 inch 8.8 inch 4.2 inch 8.8 inch / 16.1 kg (With Stand) - Option (With Speaker) - Option (With Speaker, With Stand) - Option VESA Mounting Interface 200 mm x 200 mm (for use with Specialty(Arm) Mounting hardware.
Option : SPEAKER L/R(8Ω, 10 W) Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) MAC, 640 x 480 35.000 66.667 30.
Model Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG (7267864) http://www.samsung.com CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (7267864) http://www.samsung.com/mx Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 4004-0000 http://www.samsung.com/br CHILE 800-726-7864 (SAMSUNG) http://www.samsung.
844 000 844 http://www.samsung.com/cz DENMARK 38 322 887 http://www.samsung.com/dk FINLAND 09 693 79 554 http://www.samsung.com/fi FRANCE 08 25 3260 (€ 0,15/min) http://www.samsung.com/fr GERMANY 01805 - 121213 (€ 0,14/Min) http://www.samsung.de HUNGARY 06-80-SAMSUNG (7267864) http://www.samsung.com/hu ITALIA 800 SAMSUNG (7267864) http://www.samsung.com/it LUXEMBURG 02 261 03 710 http://www.samsung.lu NETHERLANDS 0900 20 200 88 (€ 0,10/Min) http://www.samsung.
TAIWAN 0800-329-999 http://www.samsung.com/tw VIETNAM 1 800 588 889 http://www.samsung.com/vn Middle East & Africa SOUTH AFRICA 0860 7267864 (SAMSUNG) http://www.samsung.com/za U.A.E 800SAMSUNG (7267864) 8000-4726 http://www.samsung.com/mea Terms Sync Signal Sync (Synchronized) Signals refer to the standard signals that are required to display desired colors on the monitor. They are divided into Vertical and Horizontal Sync Signals.
For Better Display 1. Adjust computer resolution and screen injection rate (refresh rate) on computer as described below to enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT-LCD. { { Resolution: 1360 x 768 Vertical frequency (refresh rate): 60 Hz 2. TFT LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product.
MÉXICO IMPORTADO POR: SAMSUNG ELECTRONICS MÉXICO. S.A. de C.V. Vía Lopez Portillo No. 6, Col. San Fco. Chilpan Tultitlán, Estado de México, C.P. 54940 Tel: 01-55-5747-5100 / 01-800-726-7864 EXPORTADO POR: Samsung Electronics CO.,LTD.
PRODUCT INFORMATION (Image Retention Free) What is Image Retention ? Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (over 12 hours), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.
z z z z Use Bright colors with little difference in luminance - Cycle : Change the characters color and background color every 30 minutes Every 30 minutes, change the characters with movement. All area display Moving image together with Logo periodically. - Cycle: Display moving image together with Logo for 60 seconds after 4 hours in use.
( Please check CD's User Guide at "OSD Function", some model's will not available ) Apply the Screen Erasing function on Product z Apply the Screen Erasing function - Symptom: 2 Vertical blocks move with erasing the display - Select method . Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Eraser . Time Interval : 1 ~ 10 hours ( Recommend : 1 ) .
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.