User Guide Samsung Smart Door Lock SHP-DS510 Please review all included documentation and use the product as intended. Safety precautions must be followed to avoid personal injury or property damage.
Smart Door Lock | Table of Contents Introduction & Helpful Tips � ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� Installation � ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� Components & Tools � ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� Door Preparation � ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� �
Smart Door Lock SHP-DS510 INSTALLATION | Components & Tools Components and Drawing A Exterior Unit B Interior Unit REG D Adjustable Deadbolt SET E Strike Parts Strike G1 Screw for Strike and Dead bolt C Interior Mounting Plate G2 Screw for mounting plate F Magnet sensor Set Dust Box Reinforcement plate G3 Screw for Interior unit Door Sensor Magnet G5 Screw for Reinforcement plate Spec: FH+M4x8 G4 Screw for Interior unit Spec: FH+T4x19 Spec: PH+M4x40 Spec: FH+T5x76 Spec: M4x15 H RF Ta
Smart Door Lock SHP-DS510 | Door Preparation Step 1. Check the Door Status 1) T his lock supports door thickness of 1-3/8” to 2-5/32” (35 to 55mm). 2) Using the provided lock template, ensure that there are no obstructions that would prevent installing the lock properly. 3) Take note of which orientation the deadbolt will need to be installed, left hand or right hand. Left-handed Door Right-handed Door When viewed from the Outside, the hinge is on the left.
Smart Door Lock SHP-DS510 Step 3. Drilling 1) Drill a 2-1/8˝ (54 mm) diameter hole through the door, as indicated on the template, using a hole saw. 2) Drill a 1˝ (25 mm) mortise hole using a hole saw. 3) Drill strike plate holes using a drill bit (1/8˝, 2.5 mm). ② 25mm ① 54mm ③ 2.5mm Step 4.
Smart Door Lock SHP-DS510 | Preparing the parts 1. Adjusting the length of the dead bolt Turn the body of the dead bolt to adjust the length of the dead bolt. It can be 60mm (2-3/8”) or 70mm (2-3/4”) 0° 18 2. Changing the faceplate of the dead bolt Change the faceplate of the dead bolt following the size of a strike hole. OR OR Rectangle Strike hole : No need to change. Round Strike hole 1. Remove the strike faceplate with a screw driver. OR 2. Turn the inner faceplate to take out it. 3.
Smart Door Lock | Installing lock SHP-DS510 Inside Outside A B C J E D REG G2 H SET G3 F G4 1. Installing the Dead Bolt(E) 1. Before installation 1) Check the faceplate type of your door. 2) Make sure the deabolt directon as shown before E inserting it into a door side. 2. Insert the deadbolt from the side of the door. 3. Fix the deadbolt using two FH+T4X19 screws. G1 D * If there is round strike hole, change the faceplate, and insert the deadbolt following right side drawing. 2.
Smart Door Lock SHP-DS510 3. Installing the Mounting Plate 1. Detach the Interior Mounting Plate from the interior unit. C C 2. Fasten the interior mounting plate with three TH+M4x40 (G2) 90% of the way. 3. Align the Exterior Unit with the Interior Mounting Plate and then tighten the screws. G2 4. Cover the rubber pad on the Interior Mounting plate. CAUTION: Do not over-tighten, and check the movement of dead bolt by the mechanical key. 4.
Smart Door Lock SHP-DS510 6. Fix Screw for the Interior Unit 1. Before installing the interior unit, check the REG SET REG REG SET SET REG SET direction of the thumb turn while the dead bolt is in the OPEN POSITION. 2. Open the battery cover. 3. Align the Interior Unit on to the Interior Mounting Left-handed Plate, and attach it with 3 screws. CAUTION: Check the movement of the dead bolt Right-handed C B by the thumb turn. SET REG G3 G4 7. Final Check 1 1. Install 4 batteries.
Smart Door Lock SHP-DS510 | Setting of Right-Handed / Left Handed *All status should be checked while the dead bolt is in OPEN POSITION.
Smart Door Lock SHP-DS510 PROGRAMMING | Programming Features Exterior Interior [SET] Button Touchscreen Card Reader Open/Close Button REG Thumbturn Lever SET REG Magnetic Sensor Restart Button [REG] Button Privacy/Lockout Mode Indicator Emergency Key Hole Battery Cover Low Battery Indicator Symbols Description Symbols Description Press the [ ] button. It is Touch the [Touchscreen]. used to complete number entry.
Smart Door Lock Symbols Description Symbols Touch the Card reader with the OPEN / CLOSE User Card. U No SHP-DS510 Description Press the [OPEN/CLOSE] button. Enter the User Number. Can be set from 1 to 100. | Definitions Indicator Lamp : Indicates the operational status when the Card is being read or the lock is in operation. Locking Mode (Auto/Manual) : You can enable or disable the function for locking the door automatically when it is closed. The factory default is ‘Auto mode’.
Smart Door Lock SHP-DS510 Random Security Code : Press this code (two-digit random numbers) before the user PIN code in order to prevent the intruder to see the fingerprint marks left on the touchscreen. You can also disable this feature, but is enabled by default. Registration Button : This button is used to change Master PIN Code/User PIN Codes/User Cards or the lock settings. It is found below the battery cover of the Interior Unit.
Smart Door Lock SHP-DS510 Status Indicators Privacy Mode Indicator Low Battery Indicator Lock Activation Touch the [Touchscreen]. Touch lock with back of hand or fingers to activate. Changing the Master PIN Code REG SET Open the battery cover of the Interior Unit and press the [REG] button briefly. R When the touchscreen is illuminated, enter the current Master PIN Code (default is ‘1234’) and press the [ ] button. Press the [ ] button after pressing the [1] button.
Smart Door Lock SHP-DS510 | Managing User PIN Code/ Card Registering a User PIN Code/ Card REG SET Open the battery cover of the Interior Unit and press the [REG] button briefly. When the touchscreen is illuminated, enter the current Master PIN Code (default is ‘1234’) and press the [ ] button. Press the [ ] button after pressing the [2] button. Press the [ ] button after pressing the [1] button. Enter a User Number(1~ 100) to register the User PIN Code and press the [ ] button.
Smart Door Lock SHP-DS510 Deleting User PIN Code / User Card REG SET Open the battery cover of the Interior Unit and press the [REG] button briefly. When the touchscreen is illuminated, enter the current Master PIN Code (default is ‘1234’) and press the [ ] button. Press the [ ] button after pressing the [2] button. REG R R Press the [ ] button after pressing the [3] button. Enter the User Number (1 to 100) and press the [ ] button.
Smart Door Lock SHP-DS510 | Basic Lock Operation Overview Opening the Door with a PIN Code → Touch the [Touchscreen]. Enter the PIN Code and The door opens within one press the [ ] button. second. Opening the Door with a Card → Touch the [Touchscreen]. Touch the Card reader The door opens within one with an Access Card second. | Privacy Mode Functions Press and hold the [OPEN/CLOSE] button for more than three seconds, if three beeps deactivate the keypad.
Smart Door Lock SHP-DS510 | Programming Through Menu Mode Using Master Code Program Operation in Master Mode :M aster Program Mode Only 1 2 3 4 R 2 No 1~100 2 No 1~100 2 Delete User PIN / Card No 1~100 3 Note: M aximum number of user registration is 100.
Smart Door Lock SHP-DS510 MISCELLANEOUS | Miscellaneous Information Reset to Factory Default Resetting the lock will delete all registered information. Note: All registered Master and user data will be deleted, and the lock will be reset to default settings. REG SET Press the [REG] button for 3 seconds.
Smart Door Lock SHP-DS510 | Troubleshooting When the lock doesn’t function correctly, please check the items below. If you can’t resolve the problem, please contact the nearest service center. Problem Resolution Reference ● Check if the batteries are inserted in the correct polarity. There is no power. ● Check that the batteries have a full charge. - ● Check that the Exterior Unit cable has not come loose. I can’t change the Master PIN Code. ● There was a delay while changing the PIN Code.
Smart Door Lock Problem SHP-DS510 Resolution Reference ● Check if Auto Locking is set. When Manual Locking is set, touching the [Touchscreen] locks the door. The door won’t lock automatically when I close it. There is no response when I touch the [Touchscreen]. ● If the door doesn’t lock automatically when Auto Locking is set, then the lock has been installed incorrectly. Page 18 ● The Auto Locking function is not activated when the batteries are completely discharged.
Smart Door Lock SHP-DS510 | User Registration Table User No. PIN CODE/CARD User Name User No.
Smart Door Lock SHP-DS510 | Product Specifications Item Specifications Voltage 4 AA Alkaline 1.5V Batteries (LR6) (6V) Operation Method Electronic Control Method (PIN Code entry or Card reading) Weight 1.8Kg (including both inside and Exterior Unit) Exterior Unit Product Dimensions Interior Unit 69.8 mm (W) x 159.8 mm (H) x 35.2 mm (D) 2-3/4˝ (W) x 6-9/32˝ (H) x 1-3/8˝ (D) 70.4 mm (W) x 163.
Smart Door Lock 24 SHP-DS510
Smart Door Lock SHP-DS510 LIMITED PRODUCT WARRANTY Installation of the product is considered acceptance of warranty conditions SAMSUNG SDS CO., LTD (SAMSUNG SDS) warrants its products to be free from manufacturing defects in materials and workmanship for 12 months from the date of purchase. SAMSUNG SDS will, within said period, at its option, repair or replace any product failing to operate correctly without charge to the original purchaser or user.
Smart Door Lock SHP-DS510 Consequently, seller shall have no liability for any personal injury, property damage, or other loss based on a claim the product failed to give warning. Therefore, the installer should in turn advise the consumer to take any and all precautions for his or her safety including, but not limited to, fleeing the premises and calling police or fire department, in order to mitigate the possibilities of harm and/or damage.
Smart Door Lock SHP-DS510 | Drilling Template Sheet : 2-3/8″(60mm) Backset 5/32" Deep Ø2-1/8" Bore 1"DIA. Latch Hole.
Smart Door Lock 28 SHP-DS510
Smart Door Lock SHP-DS510 | Drilling Template Sheet : 2-3/4″(70mm) Backset Ø2-1/8" 5/32" Deep Bore 1"DIA. Latch Hole.
Smart Door Lock 30 SHP-DS510
Smart Door Lock SHP-DS510 | Tailpiece Setting • Tailpiece drawing 1. Check the thickness of your door. 2. According to your door thickness, cut the tailpiece. Note: Cut the tailpiece 5mm longer than the door thickness. Thickness of the door cutting point 5mm How to cut 1. Press the V-cut line with pincers to make more cut line. 2. Hold the the end of the tailpiece with pincers. 3. Bend it up and down until it is separated.
Smart Door Lock SHP-DS510 Product information and customer service contact SAMSUNG SDS SAMSUNG SDS Co.,Ltd., reserves the right to change availability of any item in this catalog, its design, construction, and/or its materials. Copyright © 2015, SAMSUNG SDS Co.,Ltd. All right reserved. Reproduction in whole or in part without the express written permission of SAMSUNG SDS is prohibited.