User Guide Samsung SDS Digital Door Lock SHP-A30 Please review all included documentation and use the product as intended. Before installing this product, fully read and understand this user guide. Safety precautions must be followed to avoid personal injury or property damage.
Samsung SDS Digital Door Lock SHP-A30 | Introduction Congratulations on the purchase of your Samsung SDS Digital Door Lock! Your lock has a touch sensitive number display pad. Up to 50 users can be registered to gain access with unique Codes. The touchscreen makes it convenient to enter the code and the Randomizer function helps prevent lockpicking using fingerprint traces on the touchscreen. Other convenient functions such as Automatic Locking / Sound Setting, etc.
Samsung SDS Digital Door Lock SHP-A30 | Safety Cautions Warning: This section contains important information to ensure the user’s safety and prevent potential damage to property. Please, read this section carefully and use the product accordingly. Caution when Installing Product It is not recommended to install this product in a rainy, humid, or salty place (e.g. coastal area), or a place exposed to direct sunlight for a long period of time.
Samsung SDS Digital Door Lock SHP-A30 Keep a distance of 20 cm or further when using this product. Do not scratch the fingerprint recognition component with a metal object such as a coin, key, or necklace. If your finger or the fingerprint recognition component is dirty or wet, wipe it clean to remove any moisture before using the sensor. If the surface of your finger is not smooth (wounded or swollen), your fingerprint may not be recognized.
Samsung SDS Digital Door Lock SHP-A30 INSTALLATION | Components & Tools Components and Drawing A Exterior Unit B Interior Unit D Adjustable Deadbolt F1 Screw for Strike and Dead bolt E Strike Parts Round face plate F2 Screw for mounting plate C Interior Mounting Plate Strike F3 Screw for mounting plate Dust Box Spec: FH+T4x19 F4 Screw for Interior unit F5 Screw for Reinforcement plate Spec: FH+M4x8 Spec: FH+#8(4.
Samsung SDS Digital Door Lock SHP-A30 | Door Preparation Step 1. Check the Door Status 1) This lock supports door thickness of 1-3/8” to 2-5/32” (35 to 55mm). 2) Using the provided lock template, ensure that there are no obstructions that would prevent installing the lock properly. 3) Take note of which orientation the deadbolt will need to be installed, left hand or right hand. Left-handed Door Right-handed Door When viewed from the Outside, the hinge is on the left.
Samsung SDS Digital Door Lock SHP-A30 Step 3. Drilling 1) Drill a 2-1/8˝ (54 mm) diameter hole through the door, as indicated on the template, using a hole saw. 2) Drill a 1˝ (25 mm) mortise hole using a hole saw. 3) Drill strike plate holes using a drill bit (1/8˝, 2.5 mm). 25mm 54mm 2.5mm Step 4.
Samsung SDS Digital Door Lock SHP-A30 | Preparing the parts 1. Adjusting the length of the dead bolt Turn the body of the dead bolt to adjust the length of the dead bolt. It can be 60mm (2-3/8”) or 70mm (2-3/4”) 0° 18 2. Changing the faceplate of the dead bolt Change the faceplate of the dead bolt following the size of a strike hole. OR OR Rectangle Strike hole : No need to change. Round Strike hole 1. Remove the strike faceplate.(PULL) OR 8 2. Insert the round faceplate.
Samsung SDS Digital Door Lock SHP-A30 | Installing lock Inside Outside G B C A F4 F3 I J E F2 F4 Caution when Installing Product Before installing an IoT door lock, check your wireless environment. Depending on the indoor wireless environment, an IoT door lock may not be installed or its service may not be supported. To check your wireless environment, you need a smartphone and a wireless access point (AP) in your house. Install the door lock while the door is open.
Samsung SDS Digital Door Lock SHP-A30 2. Installing the Exterior Unit 1. Ensure the Exterior Unit is aligned with the center hole of the deadbolt. 2. Attach the exterior unit. A E CAUTION: The dead bolt must be in a retracted position. Insert the Exterior Unit and pull the connector cable out above the dead bolt. 3. Installing the Mounting Plate 1. Detach the Interior Mounting Plate from the interior unit. 2. Fasten the interior mounting plate with two BH+M5x35 (F2) 90% of the way. 3.
Samsung SDS Digital Door Lock SHP-A30 5. Fix Screw for the Interior Unit C 2 C B B F4 1. Before installing the interior unit, 1) Check the direction of the thumb turn while the dead bolt is in the OPEN POSITION. 2) Check if the knob of the interior unit is placed at the center. 2. Use the cover pin to push the battery cover hole on the upper section of the interior unit to open the battery cover. 3. Insert the tailpiece of the interior unit vertically into the dead bolt. 4.
Samsung SDS Digital Door Lock SHP-A30 PROGRAMMING | Programming Features Exterior Interior Low Battery Indicator Operation LED WiFi Module (Option) [Open/Close] Button [REG] Button Fingerprint Recognition part Privacy/Lockout Mode Indicator Touchscreen Thumbturn Lever External Power Contact Restart Button C Symbols B Description Symbols Touch the [Touchscreen]. F4 Enter the Master PIN Code Mstr PIN F4 Battery Cover Description Press the [ ] button. It is used to complete number entry.
Samsung SDS Digital Door Lock Symbols Description Symbols U FP Place the finger on the fingerprint sensor U No Enter the User Number. Can be set from 1 to 50. SHP-A30 Description Repeat the process inside the rectangle. OPEN / CLOSE Press the [OPEN/CLOSE] button. | Definitions 2-Step Authentication Mode : Both PIN Code and fingerprint need to be authenticated to open the door, ensuring more security. To set this mode, one or more fingerprints need to be registered.
Samsung SDS Digital Door Lock SHP-A30 Registration Button : This button is used to change Master PIN Code/User PIN Codes/User Fingerprints or the lock settings. It is found below the battery cover of the Interior Unit. The length of time the [REG] button is pressed varies depending on the function. Resetting : Deletes all registered information and restores the factory default. After resetting, change the Master PIN Code for security.
Samsung SDS Digital Door Lock SHP-A30 | Basic Lock Operation Overview Opening the Door with a PIN Code → Touch the [Touchscreen]. Enter the PIN Code and press the [ ] button. Opening the Door with a Fingerprint → Place the registered fingerprint on the fingerprint sensor. The door opens within one second. | Lock Activation Touch the [Touchscreen]. Touch lock with back of hand or fingers to activate. 15 The door opens within one second.
Samsung SDS Digital Door Lock SHP-A30 | Status Indicators Privacy Mode Indicator Low Battery Indicator | Changing the Master PIN Code Changing Master PIN 1 Open the battery cover of the Unit and press the [REG] button briefly. Deleting User Interior PIN No 1~50 2 Adding User PIN When the touchscreen is illuminated, enter the current 2 2 Master PIN Code (default is ‘1234’) and press the [ ] button.
Samsung SDS Digital Door Lock SHP-A30 | Managing User PIN codes Adding a User PIN Code 1 Open the battery cover of the Interior Unit and press the [REG] button briefly. When the touchscreen is illuminated, enter the current Master PIN Code (default is ‘1234’) and press the [ ] button. Press the [ ] button after pressing the [1] button for the Registration mode. Changing Master PIN Press the [ ] button after pressing the [2] button for the User PIN Code managDeleting User PIN ing mode.
Samsung SDS Digital Door Lock SHP-A30 Deleting a User PIN Code 1 Changing Master PIN Open the battery cover of the Interior Unit and press the [REG] button briefly. Adding User PIN When the touchscreen is il2 luminated, enter the current Master PIN Code (default is ‘1234’) and press the [ ] button. Deleting User PIN Delete All User PIN Press the [ ] button after pressing the [2] button for Register Fingerprint the User PIN Code managing mode.
2 2 1~50 Samsung SDS Digital Door Lock Delete All User PIN 2 3 Register Fingerprint 3 1 Delete a Fingerprint 3 2 Deleting All User PIN Code SHP-A30 Fingerprint No 1~50 Fingerprint Open the battery cover of the Interior Unit and press Delete All Fingerprint the [REG] button briefly. When the touchscreen is illuminated, enter the current 3 3 Master PIN Code (default is ‘1234’) and press the [ ] button. Press the [ ] button after pressing the [1] button for the Registration mode.