User Guide Samsung Smart Door Lock SHN-WDS700 Please review all included documentation and use the product as intended. Safety precautions must be followed to avoid personal injury or property damage.
Smart Door Lock SHN-WDS700 | Table of Contents Introduction & Helpful Tips � ��� Installation � ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� Components & Tools � ��� ��� ��� ��� ��� ��� Door Preparation � ��� ��� ��� ��� ��� ��� ��� ��� ��� Preparing the parts �� Installing Lock � ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� �� 2
mponents & Tools Smart Door Lock SHN-WDS700 Installation | Components & Tools Components and Drawing A Exterior Unit B Interior Unit C Interior Rubber Pad D Interior Mounting Plate SHS-3320 SHS-3321 (With key hole) (Without key hole) E Adjustable Deadbolt F Strike Parts (Alternate Faceplate For round strike) H1 Screw for Strike and Dead bolt Strike G Magnetic Sensor Dust Box H2 Screw for mounting plate Door Side H3 Screw for Interior unit Doorframe Side I Tailpiece (Extra Parts) Spec: F
Smart Door Lock SHN-WDS700 | Door Preparation Step 1. Check the Door Status 1) T his lock supports door thickness of 1-3/8” to 2-5/32” (35 to 55mm). 2) Using the provided lock template, ensure that there are no obstructions that would prevent installing the lock properly. 3) Take note of which orientation the deadbolt will need to be installed, left hand or right hand. Left-handed Door Right-handed Door When viewed from the Outside, the hinge is on the left.
Smart Door Lock SHN-WDS700 Step 3. Drilling 1) Drill a 2-1/8˝ (54 mm) diameter hole through the door, as indicated on the template, using a hole saw. 2) Drill a 1˝ (25 mm) mortise hole using a hole saw. 3) Drill strike plate holes using a drill bit (1/8˝, 2.5 mm). ② 25mm ① 54mm ③ 2.5mm Step 4.
Smart Door Lock SHN-WDS700 | Preparing the parts 1. Adjusting the length of the dead bolt Turn the body of the dead bolt to adjust the length of the dead bolt. It can be 60mm (2-3/8”) or 70mm (2-3/4”) 0° 18 2. Changing the faceplate of the dead bolt Change the faceplate of the dead bolt following the size of a strike hole. OR OR Rectangle Strike hole : No need to change. Round Strike hole 1. Remove the strike faceplate with a screw driver. OR 2. Turn the inner faceplate to take out it. 3.
Smart Door Lock | Installing lock SHN-WDS700 Inside Outside A D C B L H3 E H2 I G 1. Installing the Dead Bolt(E) 1. Before installation 1) Check the faceplate type of your door. 2) Make sure the deabolt directon as shown before E inserting it into a door side. 2. Insert the deadbolt from the side of the door. 3. Fix the deadbolt using two FH+T4X19 screws. H1 E * If there is round strike hole, change the faceplate, and insert the deadbolt following right side drawing. 2.
Smart Door Lock SHN-WDS700 3. Installing the Mounting Plate D D H2 Left-handed Right-handed 1. Detach the Interior Mounting Plate from the interior unit. 2. According to the right or left handed door, adjust the link, and attach the mounting plate. 3. Fasten the interior mounting plate with three TH+M5x40 (H2) 90% of the way. 4. Align the Exterior Unit with the Interior Mounting Plate and then tighten the screws. 5. Cover the rubber pad on the Interior Mounting plate.
Smart Door Lock SHN-WDS700 6. Fix Screw for the Interior Unit 1. Before installing the interior unit, check the direction of the thumb turn while the dead bolt is in the OPEN POSITION. 2. Open the battery cover. 3. Align the Interior Unit on to the Interior Mounting Left-handed Plate, and attach it with 4 screws. CAUTION: Check the movement of the dead bolt Right-handed B C by the thumb turn. H3 7. Final Check 1 1. Install 4 batteries.
Smart Door Lock SHN-WDS700 | Setting of Right-Handed / Left Handed *All status should be checked while the dead bolt is in OPEN POSITION.
Smart Door Lock SHN-WDS700 Programming | Basic Lock Operation Overview Opening the Door with a PIN Code → Touch the [Touchscreen]. The touchscreen will illuminate. (If the Random Security function is enabled, press the 2 illuminated numbers.) Enter the PIN Code and press the [ ] button. The door opens within one second. Successful: Ding dong dang dong Failed: Ding dong ding dong Opening the Door with a Card → Touch the [Touchscreen]. Touch the Card reader with an Access Card.
Smart Door Lock SHN-WDS700 | Programming Features Outside Inside Touchscreen Registration Button Open/Close Button Card Reader Thumbturn Lever Magnetic Sensor Emergency Cylinder (SHS-3321 does not support.) Battery Cover Restart Button External Power Contact Symbols Description Symbols Description Press the [ ] button. It is Touch the [Touchscreen]. used to complete number entry. Press the [Registration] button.
Smart Door Lock Symbols Description Symbols SHN-WDS700 Description Enter the User PIN Code (4~12 Repeat the process inside digits). the rectangle. Touch the Card reader with the Press the [OPEN/CLOSE] User Card. button. Enter the User/Management Number. Can be set from 1 Sound Icon Display. to 70. Sound Indicators Sound Description Fur Elise Low voltage warning sound Tiritiritiriririri accompanied with [OPEN/CLOSE] button flashing red.
Smart Door Lock SHN-WDS700 | Definitions Double Authentication Mode : This mode requires both User Card and PIN Code to open the door, ensuring more security. However, Master PIN Code can open the door regardless of mode. To enable this mode, more than 1 User Card and PIN Code must be registered. This mode is disabled by default. Double-locking : Double-locking prevents the lock from being unlocked from the outside. You can enable it by using the [OPEN/CLOSE] button.
Smart Door Lock SHN-WDS700 Random Security Function : This mode prevents the disclosure of the PIN Code by entering the PIN Code after authenticating 2 arbitrarily selected numbers. When the buttons for 2 arbitrarily selected numbers are illuminated, pressing the 2 illuminated buttons illuminates the whole touchscreen. You can enable or disable the Random Security function. This function is enabled by default.
Smart Door Lock SHN-WDS700 | Programming User PIN Codes & User Cards Note: Pressing the [Registration] button is only available while the door is open. (Deadbolt must be unlocked.) Maximum number of user registration is 70. (User PIN Codes, User Cards, Key Fobs) Changing the Master PIN Code Open the battery cover of the Interior Unit and press the [Registration] button briefly.
Smart Door Lock SHN-WDS700 Registering a User Card Open the battery cover of the Interior Unit and press the [Registration] button briefly. Ding dong Touch the Card reader with the Card to register. When the touchscreen is illuminated, enter the current Master PIN Code (default Enter a User Number (1~70) to register the User Card code [ ] button. Successful: Ding dong Failed: Ding dong ding and press the [ ] button. * Choose a User Number that has not already been used.
Smart Door Lock SHN-WDS700 | Security Functions Setting the Out-of-Home Security Function When the door is closed [ ] of the touchscreen will light up. Press the [ Setting Double-locking Releasing Double-locking Press the [OPEN/ CLOSE] button for 5 seconds while the door is locked. ] button within 3 seconds. Ding dong dang Press the [OPEN/ CLOSE] button or turn the Thumbturn lever.
Smart Door Lock SHN-WDS700 Miscellaneous | Miscellaneous Information Reset to Factory Default Resetting the lock will delete all registered information. Note: After Reset, let the sensor detect the magnet to set the hand type again. All registered Master and user data will be deleted, and the lock will be reset to default settings.(Refer to the Program section on Page 15 for default values.) Press the [Registration] button for 10 seconds.
Smart Door Lock SHN-WDS700 | Troubleshooting When the lock doesn’t function correctly, please check the items below. If you can’t resolve the problem, please contact the nearest service center. Problem Resolution Reference ● Check if the batteries are inserted in the correct polarity. There is no power. ● Check that the batteries have a full charge. - ● Check that the Exterior Unit cable has not come loose. I can’t change the Master PIN Code. ● There was a delay while changing the PIN Code.
Smart Door Lock My PIN Code or Card is authenticated, but the door won’t open. SHN-WDS700 he lock may be malfunctioning. Please contact service T center. - ● Check if Auto Locking is set. When Manual Locking is set, touching the [Touchscreen] locks the door. The door won’t lock automatically when I close it. ● If the door doesn’t lock automatically when Auto Locking is set, then the lock has been installed incorrectly.
Smart Door Lock SHN-WDS700 | User Registration Table Management No. PIN CODE/CARD User Name Management No.
Smart Door Lock SHN-WDS700 | Product Specifications Item Voltage Emergency Power Source Specifications 4 AA Alkaline 1.5V Batteries (LR6) (6V) 9V Battery (6LF22) (not included) Operation Method Electronic Control Method (PIN Code entry or Card reading) Weight 1.8Kg (including both inside and Exterior Unit) Exterior Unit Product Dimensions Interior Unit 68.0 mm (W) x 180.0 mm (H) x 36.5 mm (D) 2-11/16˝ inch (W) x 7-3/32˝ inch (H) x 1-7/16˝ inch (D) 68.0 mm (W) x 180.0 mm (H) x 38.
Smart Door Lock SHN-WDS700 LIMITED PRODUCT WARRANTY Installation of the product is considered acceptance of warranty conditions SAMSUNG SNS CO., LTD (SAMSUNG SNS) warrants its products to be free from manufacturing defects in materials and workmanship for 12 months from the date of purchase. SAMSUNG SNS will, within said period, at its option, repair or replace any product failing to operate correctly without charge to the original purchaser or user.
Smart Door Lock SHN-WDS700 Consequently, seller shall have no liability for any personal injury, property damage, or other loss based on a claim the product failed to give warning. Therefore, the installer should in turn advise the consumer to take any and all precautions for his or her safety including, but not limited to, fleeing the premises and calling police or fire department, in order to mitigate the possibilities of harm and/or damage.
Smart Door Lock 26 SHN-WDS700
Smart Door Lock | Drilling Template Sheet : 2-3/8″(60mm) Backset 5/32" Deep Ø2-1/8" Bore 1"DIA. Latch Hole.
Smart Door Lock 28 SHN-WDS700
Smart Door Lock | Drilling Template Sheet : 2-3/4″(70mm) Backset Ø2-1/8" 5/32" Deep Bore 1"DIA. Latch Hole.
Smart Door Lock 30 SHN-WDS700
Smart Door Lock SHN-WDS700 | Tailpiece Setting 1. Check the thickness of your door with our • Tailpiece drawing tailpiece drawing or a ruler. 2. According to your door thickness, cut and adjust the tailpiece as following way ; ex1) Thickness : 40mm 35 40 45 50 55 cutting point ex2) Thickness : 53mm 35 40 45 50 55 cutting point 35mm 35 40 45 50 55 How to cut 1. Press the V-cut line with pincers to make more cut line. 2. Hold the the end of the tailpiece with pincers. 3.
Smart Door Lock 32 SHN-WDS700
Smart Door Lock MEMO 33 SHN-WDS700
Smart Door Lock MEMO 34 SHN-WDS700
Smart Door Lock 35 SHN-WDS700
Smart Door Lock SHN-WDS700 Product information and customer service contact SAMSUNG SNS SAMSUNG SNS Co.,Ltd., reserves the right to change availability of any item in this catalog, its design, construction, and/or its materials. Copyright © 2011, SAMSUNG SNS Co.,Ltd. All right reserved. Reproduction in whole or in part without the express written permission of SAMSUNG SNS is prohibited.