SMART CARD READER/WRITER SAM-CRM-14 System Manual Ver 1.2 SAM-CRM-14_MANUAL Rev. 1.2 Dec. 05, 2013 Copyright ⓒ 2013 Samsung SDS Co., Ltd. All rights reserved. You are strictly prohibited to copy, disclose, distribute, or use this document in part or as a whole for any purposes other than those for which this document is disclosed. This document is copyrighted and contains confidential information and other intellectual property rights of Samsung SDS Co., Ltd.
Revision History Document Name Smart Card Reader/Writer System Manual Version Date Notice 0.1 2013.06.20 Draft 1.0 2013.11.17 Revision 1.1 2013.11.18 Revision & Translation 1.2 2013.12.05 Revision System Manual – SAM-OCU-14 – 2013.12.05 Copyright ⓒ 2013 Samsung SDS Co., Ltd.
System Manual – SAM-OCU-14 – 2013.12.05 Copyright ⓒ 2013 Samsung SDS Co., Ltd.
목 차 Table of Contents 1 OVERVIEW .............................................................................................................................................. - 6 1.1 GENERAL DESCRIPTION ....................................................................................................................... - 6 - 1.2 OUTSIDE DIMENSION ........................................................................................................................... - 7 - 1.
2.8.1 Rear Cover connector – PWR ................................................................................................... - 24 - 2.8.2 Rear Cover connector – SIGNAL_1 .......................................................................................... - 24 - 2.8.3 Rear Cover connector – SIGNAL_2 .......................................................................................... - 25 - 2.8.4 Rear Cover connector – DIO ............................................................
List of Tables TABLE 1 GENERAL SPECIFICATION ....................................................................................................................... - 9 TABLE 2 SPECIFICATION OF GPS MODULE.......................................................................................................... - 13 TABLE 3 SPECIFICATION OF CARD READER/WRITER ........................................................................................... - 15 TABLE 4 SPECIFICATION OF LCD DISPLAY ..................
1 Overview 1.1 General Description The validator is installed on the bus and has a role of fare collection. It has a RF card reader/writer which comply the EMV standard and ISO 14443 Type A. The validator has a 5.7” touch screen display for passenger interface. It is compatible to a peripheral device through a multiple external interface such as Wi-Fi, Bluetooth and etc. This document informs and defines each module and specification of validator.
1.2 Outside Dimension Figure 2 Outside dimension System Manual – SAM-OCU-14 – 2013.12.05 Copyright ⓒ 2013 Samsung SDS Co., Ltd.
1.3 System Configuration 1.3.1 Block Diagram The following figure is the validator block diagram. Figure 3 Validator Block Diagram System Manual – SAM-OCU-14 – 2013.12.05 Copyright ⓒ 2013 Samsung SDS Co., Ltd.
1.4 General Specification The table below shows the general specifications of the validator. System Enclosure CPU Module Base Board Module Card Reader/Writer Barcode Reader Item Specification Dimension(mm) 193.0(W) * 319.0(H) * 61.5(D) Material Outside steel of enclosure : Material: PC-ABS Processor Samsung S5PV210, Cortex-A8 1GHz Memory RAM: 512MB, NAND Flash: 512MB OS ANDROID 4.0 WiFi/Bluetooth Module IEEE802.11b/g/n, Bluetooth 3.
2 Module Configuration The configuration of validator is as follows: CPU Module Base Board Module Card Reader/Writer Barcode Reader Touch Screen Display Speaker 2.1 CPU Module 2.1.1 General Description The CPU Module controls all the sub-modules and processes all the data in the validator. They have sufficient space for Operating System (OS) and the application data.
2.1.2 Block diagram Figure 4 Block diagram of CPU Module System Manual – SAM-OCU-14 – 2013.12.05 Copyright ⓒ 2013 Samsung SDS Co., Ltd.
2.2 Base board module 2.2.1 General Description Base board module performs major functions of validator device controlling. The Wi-Fi/BT module, CAN module and etc. are installed on the base board. 2.2.2 Layout of Base board module Figure 5 Top Layout of Base board module (Example) Figure 6 Bottom Layout of Base board module (Example) System Manual – SAM-OCU-14 – 2013.12.05 Copyright ⓒ 2013 Samsung SDS Co., Ltd.
2.2.3 Wi-Fi/Bluetooth module The validator has the Wi-Fi/Bluetooth module to communicate with the server (in the garage) and peripheral devices. The key features are as below; IEEE802.11b/g/n standard conformity, BT3.0,2.1+EDR Low standby current (with advanced power save and sleep mode) Transmit speed : 11/5.5/2/1 Mbps(11b), 54/48/36/24/18/12/9/6 Mbps(11g), 150~6.
2.3 Card Reader/Writer 2.3.1 General Description Card Reader/Writer is a high-end RF reader and it is the world first device which supports all three specification as following, (1) Contactless card spec_Mifare, ISO14443 Standard A/B, (2)Payment spec_Paywave, Paypass, JSMART, American Express and (3) EMVCo Type Approval Contact less Level 1 , NFC forum spec complaint. It also has 8(EA) of SIM slot for secure communication, RS-232(2ea) as interface method.
System Item Specification Communication RS232 * 2 RF I/F PN512 SIC9310 RC-S940 Standard ISO14443 A/B, FeliCa, Mifare, ISO15693 Input Power 12V, 300mA SAM SIM socket 8EA Switch Case open switch (PCB tamper) Table 3 Specification of Card reader/writer System Manual – SAM-OCU-14 – 2013.12.05 Copyright ⓒ 2013 Samsung SDS Co., Ltd.
2.4 Touch Screen Display 2.4.1 General Description The Touch screen display is a color graphic touch screen (5.7” inch TFT LCD) that allows passenger to input their selection. The Touch screen display is positioned ergonomically for passenger to operate easily. 2.4.2 Layout Figure 7 Layout of LCD display System Manual – SAM-OCU-14 – 2013.12.05 Copyright ⓒ 2013 Samsung SDS Co., Ltd.
Figure 8 Layout of Touch panel 2.4.3 LCD display specification Item Specification Screen Diagonal 5.7 inch Active Area 115.2(H) x 86.4(V) (mm) Pixels HxV 640 x 3(RGB) x 480 Pixel Pitch 0.18 x 0.18 (mm) Pixel Arrangement R.G.B Vertical Stripe Display Mode TN, Normally White Nominal Input Voltage VDD 3.3 typ. (Volt) Typical Power Consumption 3.74W (LCD:0.5W/LED BLU:3.24W) @ All black pattern, Full Load and VLED=12V Weight 150g(typ.), 165g(max.) Physical Size 144.0(H) x 104.6(V) x 12.
Item Specification The most suitable view angle 12 o’clock Temperature Range Operating: -30℃~+85℃ Storage: -30℃~+85℃ RoHS Compliance RoHS Compliance Table 4 Specification of LCD Display 2.4.4 Touch panel specification Item Specification Glass THK 1.1mm Film type Non-glare Tail FPC (Ni+Au) Method 4-wire resistive touch Table 5 Specification of Touch panel System Manual – SAM-OCU-14 – 2013.12.05 Copyright ⓒ 2013 Samsung SDS Co., Ltd.
2.5 Barcode Reader 2.5.1 General Description The validator has the barcode reader to read the barcode type ticket (1D or 2D). 2.5.2 Layout Figure 9 Layout of Barcode reader 2.5.3 Specification Item Specification Image Sensor CMOS Sensor, Max. 752*480, 8-bit grayscale Target Distance 5~32.5cm: Depends on code size.
2.6 Speaker 2.6.1 General Description The speaker is installed in the validator. It makes a sound for driver’s recognition. Figure 10 Layout of Speaker Items Description Rated Input Power 1.0W (Max. 1.5W) Impedance 8±15%(Ohm) Output SPL @ 0.1W/0.1M 87±2dB Resonant frequency 800±20% Hz Magnet size (mm) 11.5 * 1.5 Weight 10g Dimension (mm) 40(W) * 20(H) * 8.2(D) Table 7 Specification of Speaker System Manual – SAM-OCU-14 – 2013.12.05 Copyright ⓒ 2013 Samsung SDS Co., Ltd.
2.7 Connector and Power switch 2.7.1 Signal & Power connector 2.7.2 LAN connector System Manual – SAM-OCU-14 – 2013.12.05 Copyright ⓒ 2013 Samsung SDS Co., Ltd.
2.7.3 Power switch & Fuse holder System Manual – SAM-OCU-14 – 2013.12.05 Copyright ⓒ 2013 Samsung SDS Co., Ltd.
2.8 Connection Diagram Figure 11 Connector Layout of Rear Cover System Manual – SAM-OCU-14 – 2013.12.05 Copyright ⓒ 2013 Samsung SDS Co., Ltd.
2.8.1 Rear Cover connector – PWR Pin No Name Description 1 PWR DC_IN 2 PWR DC_IN 3 GND GND 4 GND GND Connector Option DC POWER IN 24V Table 8 Specification of PWR Connector 2.8.2 Rear Cover connector – SIGNAL_1 Pin No Name Description 1 RXD Comm 2 TXD Comm 3 GND Comm 4 RXD GND 5 TXD Comm 6 GND Comm 7 485_A Comm 8 485_B Comm 9 485_A RS232 & 485 10 485_B RS232 & 485 Table 9 Specification of SIGNAL_1 Connector System Manual – SAM-OCU-14 – 2013.12.
2.8.3 Rear Cover connector – SIGNAL_2 Pin No Name Description 1 VDD DC_OUT 3.3V 2 RXD Comm 3 TXD Comm 4 GND GND 5 GND GND 6 VDD DC_OUT 5.0V 7 485_A Comm 8 485_B Comm 9 485_A RS232 & 485 10 485_B RS232 & 485 Connector Option RS232 Comm RS 485 Comm RS232 or 485 (Optional) Table 10 Specification of SIGNAL_2 Connector 2.8.
2.9 Operation & Usage 1. Turn on the validator, check the android OS booting by the LCD display. After boot-up, the operator can use the validator. 2. When the validator turned on, the card r/w makes beep sound 1 time. 3. There are three (3) colors LED (Red, Blue, and Green) on the rear cover. The LED color can be configured by setting. Figure 12 LED configuration of rear cover 4.
6. There are USB port and External Micro SD card slot on the right side of validator. 7. There are Digital In/Output port, Serial communication port and LAN (Ethernet) port on the rear cover of validator. So, it supports variable interface. 8. The validator has audio feedback to support the announcement for passenger. FCC STATEMENT CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Thank You Tel : +82-2-3429-2114 E-mail : sdspr@samsung.com http://www.sds.samsung.co.kr System Manual – SAM-OCU-14 – 2013.12.05 Copyright ⓒ 2013 Samsung SDS Co., Ltd. All rights reserved | Confidential Copyright ⓒ 2013 Samsung SDS Co., Ltd.