RFID Gun reader for SmartCompact User Manual SmarTerminal Computers, Inc. Ver 0.
Disclaimer SmarTerminal and SmartCompact are registered trademarks of Sammi Information Systems Co., Ltd. All other brand names, product names, or trademarks belong to their respective holders. Head Quarters Sammi Information Systems Co.,Ltd. 103-15, Galwor –dong, Yongsan-Gu, Seoul, Korea Tel. 82 -2-790-5508 / Fax. 82-2-790-5509 Email. sales@sammicomputer.co.kr Web. www.sammicomputer.co.kr Us Office SmartTerminal Computers, Inc. 5200 Orange Ave. Suite 212 Cypress, CA 90630 Tel. 1-714-761-5300 Fax.
Table of Contents Introduction....................................................................................................................................... 4 Chapter 1 Get to know more about RFID Gun reader................................................................... 5 1.1 Make sure you have everything ....................................................................................... 5 1.2 Appearance ....................................................................................
Introduction This quick reference guide allows you to use all the advanced features of SmartCompact effectively. Please go through it once before using SmartCompact handheld terminal. User's Information Cautions Modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC compliance Information This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: 1.
Chapter 1 Get to know more about RFID Gun reader 1.
1.2 Appearance 1.2.1 Front side UHF antenna Features and description Features Function / Description RFID Antenna RFID antenna is located in front side of Gun reader 1.2.
Name Function Power LED Shows green light for 5 seconds when user triggers the gun Battery capacity LED Shows battery capacity status (see below table for details) Communication LED When IrDA communication is successful between Gun reader and SmartCompact, Communication LED shows green light (blinking) as user triggers the gun.
1.2.3 Top side Screws for attaching to SmartCompact 1.2.4 Bottom side 2200mAH battery 1.2.
Features and description Features Function / Description Battery out button To take out battery, user should push this button. 1.2.6 Right side DC input jack Features and description Features Function / Description DC input jack To charge RFID reader, user should connect AC/DC adapter to this DC input jack. 1.2.
Chapter 2 Power settings and connections 2.
2.2 Battery charging using power adapter In the beginning, user must charge the battery at least for 4.5 hours to use the RFID Gun reader. 2.2.1 Charging with AC/DC adapter Prepare AC/DC adapter (5V, 3A) and power cable for RFID Gun reader. This AC/DC adapter is compatible with that of SmartCompact. Insert power cable to AC/DC adapter like below photo: Open RFID Gun reader’s DC input jack cover and insert DC adapter output cable.
2.2.2 Charging with Battery charger To charge the battery pack, user can also use 3 pack Battery charger. Three batteries can be charged at the same time. Under charging, the LED light is red and turns green after fully charged.
Chapter 3 Setting up SmartCompact RFID Gun reader 3.1 How to set CAB Files in SmartCompact Connect USB Active sync cable between your computer and SmartCompact. When Active Sync program is opened, click Explore.
Click DiskOnChip folder. Save necessary CAB file in the DiskOnChip folder.
Click DiskonChip/Cold Reset folder of SmartCompact. Click corresponding Cab File.
3.2 How to connect SmartCompact to RFID Gun reader Insert SmartCompact to RFID Gun reader in below direction: SmartCompact combined to RFID Gun reader: Tighten the screws (2 pcs) firmly in order to hold the combination.
3.3 How to remove SmartCompact from RFID Gun reader Loosen the screws (2 pcs) in order to undo the combination.
Chapter 4 Using RFID Gun reader 4.1 How to operate RFID Gun reader To operate RFID Gun reader, user needs RFID Gun reader and SmartCompact (power on) with program files installed. 4.1.1 How to install program files in SmartCompact To install program files in SmartCompact, user can follow one of below three methods: 1) Using Sync cable To do this, user should have Microsoft ActiveSync program (v.4.2 or higher) installed in the computer. Connect SmartCompact to the computer with USB or Serial Sync cable.
When Explore window is opened, copy and paste necessary program files from computer to DiskOnChip folder of SmartCompact (shown as Mobile Device).
2) Using CF/SD cards User can save necessary files to CF or SD card and insert it into SmartCompact. Check the locations of CF/SD card slots below: CF Card Slot SD Card Slot Copy the necessary files and paste them to DiskOnChip folder of SmartCompact.
4.1.2 How to operate RFID Gun reader Slide SmartCompact to RFID Gun reader in below direction. After combining SmartCompact and RFID Gun reader, click to open program CAB files to install.
After program setting is done, target the RFID tag in front of antenna side and trigger the RFID Gun reader. TAG sample (ISO 18000 – 6C EPC CLASS1 GEN 2) UHF Gun reader can read in 0.5-1.5m distance and supports EPC C1G2, ISO18000-6B/C tags.
Appendix A RFID Gun reader Specification Highlights RFID Gun reader(optional) Radio frequency UHF (US: 902-928MHz) Tag support UHF: EPC C1G2, ISO18000-6B/C Output power: 0.
Appendix B Version Table Version: 0.93 Release Date: 09/03/2007 Version: 0.