UHF Wireless System Owners Manual • AF1 Instrument Transmitter • AG1 Instrument Transmitter • AP1 Receiver • UR1 Receiver SAMSON
Table of Contents ENGLISH DEUTSCHE Introduction 1 QuickStart 2 Guided Tour - AP1 Receiver 4 Guided Tour - AF1 / AG1 Transmitter 7 Guided Tour - UR1 Receiver 45 Setting Up and Using Your AirLine System 9 Specifications 48 Channel Plan 50 Einleitung 23 Schneller Einstieg 24 Übersicht - Empfänger AP1 26 Übersicht - Sender AF1 / AG1 29 AirLine System einrichten und einsetzen 31 Technische Daten 48 Frequenzzuordnung der Empfangskanäle 50 FRANCAIS Introducción 34 Arranque rápido 35 Recorrido guiado – Recepto
Introduction Samson AirLine The Samson AirLine UHF guitar system detailed in this manual is designed to replace the cable between your electric guitar or bass and your onstage amplifier or PA mixer, freeing you to roam the stage or even visit the audience in the middle of your performance! It operates in the uncrowded 801 - 805 MHz UHF frequency range and contains an AP1 “stomp box”-style receiver and either of two plug-in micro-transmitter models—an AF1 (designed to fit the recessed style jack in Fender
ENGLISH Samson AirLine QuickStart If you’ve had some prior experience using wireless systems, these QuickStart instructions will get you up and running with your AirLine UHF guitar system in a matter of minutes! Detailed instructions for setting up and using your AirLine system can be found on page 9 of this manual, and the “Guided Tour” sections on pages 4 - 8 provide full descriptions of all AirLine component controls and displays. 1.
QuickStart Samson AirLine 9. Do a walkaround through the intended area of coverage while observing the receiver’s “TX/Peak” LED; it should continue to be lit steadily green, indicating sufficient RF reception in all areas of coverage. If not, reposition the AP1 or its antennas as necessary. 10.
Guided Tour - AP1 Receiver ENGLISH Samson AirLine 2 ON BATT. LOW POWER 1: Power switch - Move this switch in the direction of the arrow to turn power to the AP1 on; move it away from the arrow to turn power off. 3 2: Power On / Battery Low LED - This LED lights green whenever the AP1 is powered on and it lights red whenever the battery in the AP1 is running low.
Guided Tour - AP1 Receiver Samson AirLine S • • • 5 ∞LEVEL LEVEL PICKUP 8: Plastic screwdriver - Specially designed for use in adjusting the AP1 Squelch control (see #11 on the following page). See the “Setting Up and Using Your AirLine System” section on page 9 in this manual for more information. ACTI VE HI 7: Battery compartment - Insert a standard 9-volt alkaline battery here, being sure to observe the plus and minus polarity markings shown. We recommend the Duracell MN 1604 type battery.
Guided Tour - AP1 Receiver ENGLISH Samson AirLine 9: Output jack - Use this standard unbalanced high impedance (5 - 10 K Ohm) 1/4" jack to connect the AP1 to your amplifier or audio mixer. Wiring is as follows: tip hot, sleeve ground. OUTPUT 10: DC input - Connect an optional 12 volt 200 mA power adapter (available from your Samson dealer) here. WARNING: Do not substitute any other kind of power adapter; doing so can cause severe damage to the AP1 and will void your warranty.
Guided Tour - AF1 / AG1 Transmitters 3 4 5 1 AF1 15dB PAD POWER Note: The AF1 and AG1 transmitters are functionally identical apart from the angling of the 1/4” plug. For purposes of illustration, only the AF1 is shown on these pages. 1: Plug - Insert this standard 1/4” plug into your electric guitar or electric bass.
Guided Tour - AF1 / AG1 Transmitters 3: 15 dB Pad - Move this switch in the direction of the arrow to reduce the output of the AF1 or AG1 by 15 dB when your instrument is putting out too hot a signal. See the “Setting Up and Using the AirLine System” section on page 9 in this manual. N O S M A S ENGLISH Samson AirLine 6 A F1 7 15 dB PA D PO WE R 4: Power switch - Move this switch in the direction of the arrow to turn power to the AF1 or AG1 on; move it away from the arrow to turn power off.
Setting Up and Using Your AirLine System Samson AirLine 1. For your AirLine system to work correctly, both the receiver and transmitter must be set to the same channel. Remove all packing materials (save them in case of need for future service) and check to make sure that the supplied AP1 receiver and AF1 or AG1 transmitter are set to the same channel (a complete channel plan is printed on page 47 in this manual).
ENGLISH Samson AirLine Setting Up and Using Your AirLine System connect a 12-volt AC adapter (available as an option from your Samson dealer). Turn the AP1 on momentarily to confirm that the battery has been installed correctly (or that the adapter has been connected correctly); the “On/Battery Low” LED should light green and not red. Then turn the AP1 power off. 6. Make the physical cable connection between the AP1 output jack and an audio input of your amplifier or mixer.
Setting Up and Using Your AirLine System Samson AirLine 12. When first setting up your AirLine System in a new environment, it’s always a good idea to do a walkaround in order to make sure that coverage is provided for your entire performance area. Accordingly, turn down the level of your audio system and turn on both the transmitter and receiver.
FRANÇAIS Samson AirLine Introduction Bienvenue sur Samson AirLine. Envolez-vous vers la liberté grâce aux systèmes sans fil du nouveau millénaire ! Les microphones et les systèmes d'instruments sans fil ont été développés à l'origine pour supprimer les câbles et offrir une complète liberté de mouvement.
Prise en main Samson AirLine informations à ce sujet. Si vous possédez déjà une certaine expérience des systèmes sans fil, ces instructions de prise en main vous permettront de rendre opérationnel en quelques minutes seulement le système AirLine sans fil UHF pour guitares.
Samson AirLine Prise en main FRANÇAIS 8. Placez l'amplificateur et la console sous tension en veillant à garder un réglage de volume au minimum. Réglez le niveau de sortie de l'instrument au maximum et commencez à jouer au niveau souhaité tout en observant le témoin “TX/Peak” de l'AP1. Si ce témoin s'allume en rouge (indiquant une distorsion) alors que le réglage de niveau du récepteur AP1 est réglé au minimum, activez l'atténuateur 15 dB de l'émetteur.
Visite guidée – Récepteur AP1 Samson AirLine 1: Interrupteur Power - Poussez cet interrupteur en direction de la flèche pour placer le récepteur AP1 sous tension ; poussez l'interrupteur à l'opposé de la flèche pour placer l'appareil hors tension. 1 4 ACTI VE • • • • ∞LEVEL • 5 AP1 U H F RE CE IVE R 6 OPEN FRANÇAIS 15 TX PEAK LEVEL PICKUP S 4: Potentiomètre de volume - Ce potentiomètre permet de régler le niveau du signal audio dirigé vers la sortie de l'AP1 (#9 en page 6).
Visite guidée – Récepteur AP1 Samson AirLine ON BATT. LOW 6: Cache du compartiment de la pile - Poussez légèrement sur le cache pour accéder au compartiment de la pile de l'AP1 (voir illustration ci-dessous, #7). S ∞LEVEL LEVEL PICKUP • • ACTI VE HI • • TX PEAK & • FRANÇAIS POWER 5: Antennes - Le montage sur pivots des antennes de l'AP1 autorise une rotation optimale.
Visite guidée – Récepteur AP1 9: Connecteur de sortie - Reliez l'AP1 à l'amplificateur ou à votre console de mixage à l'aide d'un jack 6,35 mm asymétrique à haute impédance (5 - 10 kOhm). Câblage : Pointe=Point chaud, Bague=Masse. Samson AirLine OUTPUT 11: Réglage du Squelch - Ce réglage détermine la portée maximale de l'AP1 avant dégradation ou perte du signal audio.
Visite guidée – Emetteur AF1 / AG1 Samson AirLine 2 3 4 5 FRANÇAIS 1 AF1 15dB PAD POWER Note : Les caractéristiques des émetteurs AF1 et AG1 sont rigoureusement identiques, exception faite de l'angle du jack 6,35 mm. Seul l'AF1 est représenté dans les illustrations proposées par ce manuel. 1: Connecteur - Ce jack 6,35 mm s'insère dans votre guitare électrique ou dans votre basse.
Visite guidée – Emetteur AF1 / AG1 N O S M A S 3: Atténuateur 15 dB - Poussez le bouton de l'atténuateur vers la flèche pour atténuer le signal de sortie de l'AF1 ou de l'AG1 de 15 dB si celui-ci est trop élevé. Reportez-vous à la section “Configuration et utilisation du système AirLine” en page 20 pour obtenir de plus amples informations.
Samson AirLine Configuration et utilisation du système AirLine Les réglages de configuration et d'utilisation de votre système AirLine ne prennent que quelques minutes : FRANÇAIS 1. Pour que votre système AirLine fonctionne correctement, veillez à ce que l'émetteur et le récepteur soient tous deux réglés sur le même canal.
Configuration et utilisation du système AirLine Samson AirLine adaptateur 12 Volts courant alternatif (disponible chez votre distributeur Samson). Placez quelques instants l'AP1 sous tension pour vous assurer que la pile est correctement installée (ou que l'adaptateur est correctement connecté) ; le témoin “On/Battery Low” doit rester allumé en vert si l'alimentation est correcte. Pour finir, replacez l'AP1 hors tension. 6.
FRANÇAIS Samson AirLine Configuration et utilisation du système AirLine de volume de l'AP1 est suffisamment élevé. La commande Level doit logiquement être positionnée face à la marque lorsque vous travaillez avec des instruments équipés de micros actifs ou à niveau élevé. 11. Baissez temporairement le niveau de l'amplificateur ou de la console, placez l'émetteur hors tension mais laissez le récepteur AP1 sous tension.
Einleitung Samson AirLine Willkommen bei Samson AirLine – dem Drahtlos-System für das neue Jahrtausend! Drahtlose Mikrofon- und Instrumentensysteme wurden ursprünglich entwickelt, um Kabel überflüssig zu machen und eine ungeahnte Bewegungsfreiheit zu bieten. AirLine geht noch einen Schritt weiter und verwendet Sender, die klein, leicht, aerodynamisch und fast unsichtbar sind und dem Anwender eine völlig “stressfreie” Erfahrung vermitteln.
Samson AirLine Schneller Einstieg Vertrieb in Verbindung. Wenn Sie bereits Erfahrungen mit Drahtlos-Systemen besitzen, werden Sie mit diesen Schnellstart-Anleitungen Ihr AirLine UHF Gitarrensystem schon in wenigen Minuten einsetzen können! Detaillierte Anleitungen zum Einrichten und Anwenden Ihres AirLineSystems finden Sie auf Seite 31 dieses Handbuchs. Die “Rundgang”-Abschnitte der Seiten 26 - 30 liefern eine detaillierte Beschreibung aller Regler und Anzeigen der AirLine-Komponenten. 1.
Schneller Einstieg Samson AirLine 6. Drehen Sie den Level-Regler des AP1 ganz nach links und schalten Sie dann den AP1 ein. Die “Power” LED leuchtet jetzt konstant grün. 7. Schalten Sie Ihren AF1 oder AG1 Sender ein. Die “TX/Peak” LED des AP1 Empfängers sollte konstant grün leuchten und damit anzeigen, dass er gültige Radiofrequenz-Signale (RF) empfängt und richtig platziert ist. 8. Schalten Sie den angeschlossenen Verstärker oder Mischer ein, aber lassen Sie seinen Pegel ganz zurückgedreht.
Übersicht - Empfänger AP1 Samson AirLine 2 ON BATT. LOW POWER 1: Netzschalter – Bewegen Sie diesen Schalter in Richtung des Pfeiles, um den AP1 einzuschalten. Bewegen Sie ihn vom Pfeil weg, um den AP1 auszuschalten. 3 2: Ein/Batterie leer LED – Diese LED leuchtet grün, wenn Sie den AP1 einschalten, und rot, wenn die Batteriespannung des AP1 nachlässt.
Übersicht - Empfänger AP1 Samson AirLine 5: Antennen – Da die beiden AP1 Antennen auf einem Schwenkgelenk montiert sind, können sie in alle Richtungen gedreht und somit optimal positioniert werden. Bei normalem Betrieb sollten beide Antennen vertikal aufgerichtet und leicht nach außen gerichtet sein. Zum Transport des AP1 können die Antennen nach innen geklappt werden.
Übersicht - Empfänger AP1 Samson AirLine Handbuch. 9: Ausgangsbuchse – Über diese asymmetrische hoch-ohmige (5 - 10 K Ohm) 1/4" Buchse können Sie den AP1 an Ihren Verstärker oder Audiomischer anschließen. Die Verdrahtung ist: Spitze/heiß, Schirm/Masse. OUTPUT 10: Gleichstrom-Eingang – Hier können Sie einen optionalen 12 Volt 200 mA Netzadapter anschließen (erhältlich bei Ihrem Samson-Händler). ACHTUNG : Verwenden Sie keine andere Art von Netzadapter.
Übersicht - Sender AF1 / AG1 2 3 4 Samson AirLine 5 1 AF1 15dB PAD POWER 1: Stecker – Stecken Sie diesen 1/4" Stecker in Ihre E-Gitarre bzw. Ihren E-Bass. Beachten Sie bitte, dass der Stecker beim AF1 (der in die vertieft angebrachte Buchse von Gitarren des Typs Fender Stratocaster™ passt) anders abgewinkelt ist als beim AG1 (der in alle anderen Standard-Gitarrenbuchsen passt).
Übersicht - Sender AF1 / AG1 3: 15 dB Dämpfung – Bewegen Sie diesen Schalter in die Richtung des Pfeils, um den Ausgangspegel des AF1 oder AG1 um 15 dB zu bedämpfen, wenn Ihr Instrument ein zu starkes Signal ausgibt. Siehe Abschnitt “AirLine System einrichten und einsetzen” auf Seite 31 in diesem Handbuch.. N O S M A S Samson AirLine 6 A F1 7 15 DEUTSCHE dB PA D PO WE R 4: Netzschalter – Bewegen Sie diesen Schalter in Richtung des Pfeiles, um den AP1 oder AG1 einzuschalten.
AirLine System einrichten und einsetzen Samson AirLine Das grundlegende Verfahren zum Einrichten und Einsetzen Ihres AirLine Systems dauert nur wenige Minuten: 1. Damit Ihr AirLine System richtig funktioniert, müssen Empfänger und Sender auf den gleichen Kanal eingestellt sein.
Samson AirLine AirLine System einrichten und einsetzen Sie dann vorsichtig die Klappe. Sie können auch einen 12-Volt Wechselstromadapter anschließen (als Sonderzubehör bei Ihrem Samson-Händler erhältlich). Schalten Sie den AP1 kurz ein, um sicherzustellen, dass die Batterie korrekt eingesetzt wurde (oder dass der Adapter korrekt angeschlossen wurde). Die “Ein/leere Batterie” LED sollte grün (nicht rot) leuchten. Schalten Sie den AP1 dann aus. 6.
AirLine System einrichten und einsetzen Samson AirLine 11. Drehen Sie den Pegel Ihres Verstärkers oder Mischers vorübergehend zurück und schalten Sie Ihren Sender aus. Lassen Sie den AP1 Empfänger eingeschaltet. Stellen Sie dann den zuvor eingestellten Pegel Ihres Verstärkers oder Mischer wieder her. Bei ausgeschaltetem Sender sollte der Ausgang des Empfängers völlig stumm sein. In diesem Fall können Sie mit dem nächsten Schritt fortfahren.
Samson AirLine Introducción ¡Bienvenido al Samson AirLine – el sistema inalámbrico para el nuevo milenio!. Los micrófonos y los sistemas de instrumentos inalámbricos fueron desarrollados originalmente para eliminar cables y ofrecer una libertad de movimientos incomparable. El AirLine lleva este concepto a un nuevo nivel haciendo que los transmisores sean tan pequeños, ligeros y aerodinámicos que sean prácticamente invisibles, lo que le da al usuario una experiencia de total “libertad real”.
Arranque rápido Samson AirLine Si ya tiene alguna experiencia previa en el uso de sistemas inalámbricos, ¡estas instrucciones de Arranque rápido harán que se ponga en marcha con su sistema UHF de guitarra AirLine en cuestión de un par de minutos!.
Samson AirLine Arranque rápido 7. Encienda su transmisor AF1 o AG1. El piloto “TX/Peak” en el receptor AP1 debería iluminarse en verde para indicar que está recibiendo una señal RF válida y que está colocado y situado correctamente. 8. Encienda el amplificador o mezclador al que tenga conectado el receptor pero mantenga su volumen totalmente abajo. Ajuste el nivel de salida de su instrumento al máximo y comience a tocar a un nivel de ejecución normal mientras observa el piloto “TX/Peak” del AP1.
Recorrido guiado – Receptor AP1 Samson AirLine 1: Interruptor Power – Mueva este interruptor en la dirección de la flecha para encender el AP1; desplácelo en el sentido opuesto para apagar la unidad. 1 4 ACTI VE • • • • ∞LEVEL • 5 AP1 U H F RE CE IVE R 6 OPEN ESPAÑOL 37 TX PEAK LEVEL PICKUP S 4: Control Level – Este mando ajusta el nivel de la señal audio que está siendo emitida a través del conector de salida del AP1 (vea el punto 9 de la página 6).
Recorrido guiado – Receptor AP1 Samson AirLine ON BATT. LOW POWER TX PEAK LEVEL PICKUP 6: Muesca del compartimento de pila – Pulse ligeramente sobre esta muesca para abrir el compartimento de la pila del AP1 (vea el punto 7 siguiente). S ∞LEVEL HI • • ACTI VE & • • 5: Antenas – El montaje giratorio permite una rotación completa para una colocación óptima de las dos antenas del AP1.
Recorrido guiado – Receptor AP1 9: Clavija de salida - Use este conector standard de 6,3 mm no balanceado y de alta impedancia (5 - 10 KOhmnios) para conectar el AP1 a su amplificador o mezclador audio. El cableado interno es: punta activo, lateral masa. Samson AirLine OUTPUT 10: Entrada DC – Conecte aquí un adaptador de corriente opcional de 12 voltios 200 mA (disponible a través de su distribuidor Samson).
Samson AirLine Recorrido guiado – Transmisor AF1 / AG1 2 3 4 5 1 AF1 15dB PAD POWER ESPAÑOL Nota: Los transmisores AF1 y AG1 son totalmente idénticos en cuanto a funciones si exceptuamos el conector de 6,3 mm en ángulo de uno de ellos. En todas las ilustraciones, solo mostraremos el modelo AF1. 1: Conector – Inserte este conector standard de 6,3 mm en su guitarra o bajo eléctrico.
Recorrido guiado – Transmisor AF1 / AG1 4: Interruptor Power – Desplace este interruptor en la dirección de la flecha para encender la unidad; muévalo en el sentido opuesto para apagar el AF1 o AG1. 5: Antena – Debería extender completamente esta antena flexible fija en condiciones normales de uso. Para una mayor información acerca de la colocación de las antenas, vea la sección titulada “Ajuste y uso de su sistema AirLine” en la página 42 de este manual.
Samson AirLine Ajuste y uso de su sistema AirLine El procedimiento básico de ajuste y uso de su sistema AirLine solo le llevará unos pocos minutos: 1. Para que su sistema AirLine funcione correctamente, tanto el receptor como el transmisor deberán estar ajustados al mismo canal.
Ajuste y uso de su sistema AirLine Samson AirLine del compartimento de la pila del AP1 y abra la tapa del mismo (no use demasiada fuerza cuando abra o cierre la tapa de la pila; tiene un gozne de cierre y no debe ser separada de la carcasa). Introduzca una pila alcalina de 9 voltios nueva y después cierre con cuidado la tapa del compartimento de la pila. De forma alternativa, también puede conectar un adaptador de corriente AC de 12 voltios (disponible de forma opcional en su distribuidor Samson).
Samson AirLine Ajuste y uso de su sistema AirLine 10. Si escucha cualquier distorsión o si el piloto “TX/Peak” del AP1 se ilumina en rojo incluso con el parche de 15 dB activado y el control de nivel al mínimo (completamente a la izquierda), reduzca el nivel de salida de su instrumento hasta que el piloto ya no se ilumine.
Guided Tour - UR1 Receiver / Front Panel 1: Antennas (A and B) - The antenna mountings allow full rotation for optimum placement. In normal operation, both Antenna A (the antenna on the left) and Antenna B (the antenna on the right) should be placed in a vertical position. Both antennas can be folded inward for convenience when transporting the UR1. See the “Setting Up and Using the AirLine System” section on page 16 in this manual for information about antenna installation and positioning.
Samson AirLine Guided Tour - UR1 Receiver / Front Panel 4: A/B Receiver LEDs - When signal is being received, one of these will be lit green, showing you whether the (left) “A” or (right) “B” receiver is currently being used. The UR1 constantly scans its two antennas and automatically selects whichever is receiving the strongest, clearest signal.
Guided Tour - UR1 Receiver / Rear Panel 1 AC CABLE LOCK 1: DC input - Connect the supplied 12 volt 160 mA power adapter here, using the strain relief as shown in the illustration below. WARNING: Do not substitute any other kind of power adapter; doing so can cause severe damage to the UR1 and will void your warranty.
Samson AirLine Specifications Transmitter (AF1 / AG1) RF Output Power (5mW) Frequency Stability Spurious Modulation Factor Pre-emphasis Maximum Input Level Input Impedance THD Audio Frequency Response Operating Power Voltage Current Consumption Battery Life Output Antenna Controls Indicators -4dB Minimum, +3dB Maximum -40kHz Minimum, 40kHz Maximum 1µW 13kHz Minimum, 15kHz Typical, 17kHz Maximum, Input 1kHz-10dBv 50 µsec +2 dBv 2K ohms < 2% (1 kHz deviation 15kHz) 50Hz - 15kHz (±3.5 dB) 1.5V Typical, 1.
Specifications Intermediate Frequency Operating Distance Noise Reduction Deemphasis Output Connector Power Input Jack Operating Temperature Storage Temperature Receiving Sensitivity Squelch Sensitivity S/N Ratio (when comparing to S=0dBv) Audio Output Level at div. f15 kHz Maximum Output Level Audio Frequency Response THD (at SG output 56 dBuv) Output Impedance Power Current Consumption Peak LED Lighting div. frequency Antenna Controls Display Samson AirLine 10.
Samson AirLine System Features Mid frequencies: Channel U1 U2 U3 U4 U5 U6 Frequency 801.375 MHz 801.875 MHz 803.125 MHz 803.750 MHz 804.500 MHz 804.
FCC Rules and Regulations Samson wireless systems are type accepted under FCC rules parts 90, 74 and 15. Licensing of Samson equipment is the user’s responsibility and licensability depends on the user’s classification, application and frequency selected. This device complies with RSS-210 of Industry & Science Canada.