Designer Lockers Options Manual

ManualsBrandsSalsbury Industries ManualsFurniture33000 Series

Designer Locker Options - 33000 Series

Installation Instructions

SALSBURY INDUSTRIES

1010 East 62

Street, Los Angeles, CA 90001-1598

Phone: 1-800-562-5377 Int’l Phone: 323-846-6700

Fax: 1-800-562-5399 Int’l Fax: 323-846-6800

www.lockers.com engineering

@lockers.com

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Thank you for selecting Salsbury’s options for designer lockers. These instructions are intended to assist you in assembling various optional items

onto the lockers. Locker fillers may be cut to special sizes for custom installations

Vertical In-Line Filler and Flat Top In-Line Filler

Install the vertical in-line filler by fastening it to the lockers by

installing screws from inside the lockers into the vertical filler. Install

optional 48” long cleats for greater stability by installing screws from

inside the lockers into the cleats. Install two 12” long cleats 3/4” from

the top edge of the lockers by installing screws from inside the

lockers into the cleats then install one additional cleat at the same

elevation onto the vertical in-line filler. Fasten the flat top in-line filler

to the cleats with liquid nails (or similar product). #8 x 1-1/4” screws

are provided for installation of the vertical filler and cleats.

Vertical In-Line Filler and Sloping Hood In-Line Filler

Install the vertical in-line filler by fastening it to the lockers by

installing screws from inside the lockers into the vertical filler. Install

optional 48” long cleats for greater stability by installing screws from

inside the lockers into the cleats. Install two 12” long cleats 3/4” from

the top edge of the sloping hoods by installing screws into the cleats

and through the sloping hoods then install one additional cleat onto

the vertical in-line filler 3/4” from its top edge. Fasten the sloping

hood in-line filler to the cleats with liquid nails (or similar product).

#8 x 1-1/4” screws are provided for installation of the vertical filler

and cleats.

Summary of content (3 pages)

PAGE 1
Designer Locker Options - 33000 Series Installation Instructions Thank you for selecting Salsbury’s options for designer lockers. These instructions are intended to assist you in assembling various optional items onto the lockers. Locker fillers may be cut to special sizes for custom installations. Vertical In-Line Filler and Flat Top In-Line Filler Install the vertical in-line filler by fastening it to the lockers by installing screws from inside the lockers into the vertical filler.
PAGE 2
Designer Locker Options - 33000 Series Installation Instructions Vertical Corner Filler and Flat Top Corner Filler Vertical Corner Filler and Sloping Hood Corner Filler Vertical corner fillers are comprised of a 3” and a 2” wide piece, each 72” long. Install the vertical corner filler pieces by vertically overlapping the 3” wide piece beyond the 2” wide piece as shown in the illustration. Fasten the pieces to the lockers by installing screws from inside the lockers into the vertical corner fillers.
PAGE 3
Designer Locker Options - 33000 Series Installation Instructions Additional Shelves An additional shelf is installed into a locker compartment by attaching two L-brackets to each side wall of the locker and to the bottom of the additional shelf. #10 x 3/4” long screws are provided for the installation. SALSBURY INDUSTRIES 1010 East 62nd Street, Los Angeles, CA 90001-1598 Phone: 1-800-562-5377 Int’l Phone: 323-846-6700 Fax: 1-800-562-5399 Int’l Fax: 323-846-6800 www.lockers.com engineering@lockers.