User's Manual

ManualsBrandsSALIX TECHNOLOGY ManualsElectronicsWifi Module

Table Of Contents

SMC-90M 802.11 b/g/n Wifi Module

SMC-90M is an 802.11b/g/n Wireless USB interface LGA module that enables devices

with high performance wireless connectivity.

FEATURES

•

PHY data rate up to 144.4 Mbps using 20MHz bandwidth,

SPECIFICATIONS

Standards

IEEE 802.11 b/g/n

Chipset

AP6212

Frequency Band

2.4 - 2.483 GHz

Encryption

64/128 bit WEP, WPA,WPA2, IEEE 802.1x

Mode

2.4GHz Band:

802.11n (HT20, MCS7)

802.11g (54Mbps)

802.11b

Receive Sensitivity

2.4GHz:

802.11b: -80 dBm max. @ 11Mbps

802.11g: -65 dBm max. @ 54Mbps

802.11n (HT20): -64 dBm max. @ 144.4Mbps

DC Voltage

3.3V (Typical)

Host Interface

USB 2.0

Antenna

Onboard antenna (1T1R)

Host Connector

Wifi Module

Temperature

Operating: 0 ~ 70 Celsius

Storage: -20 ~ 70 Celsius

Humidity

Storage: 10 ~ 80% (Non Condensing)

Dimensions (L x W x H) 38.5 x 23.0 x 2.85 mm

*Specifications are subject to change without further notice.

Summary of content (8 pages)

PAGE 1
SMC-90M 802.11 b/g/n Wifi Module SMC-90M is an 802.11b/g/n Wireless USB interface LGA module that enables devices with high performance wireless connectivity. FEATURES • PHY data rate up to 144.4 Mbps using 20MHz bandwidth, SPECIFICATIONS Standards IEEE 802.11 b/g/n Chipset AP6212 Frequency Band 2.4 - 2.483 GHz Encryption 64/128 bit WEP, WPA,WPA2, IEEE 802.1x 2.4GHz Band: Mode 802.11n (HT20, MCS7) 802.11g (54Mbps) 802.11b 2.4GHz: Receive Sensitivity 802.11b: -80 dBm max. @ 11Mbps 802.
PAGE 2
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limit s for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 3
Quick Start Guide for Driver Compilation and Installation Contents Introduction ...............................................................................................................1 1. Using install.sh Script for PC-Linux ...................................................................1 2. Decompress the driver source tar ball .................................................................1 3. 4. 5. 6. 7. Selecting Chip Type with make_drv Script (for compound release) ....................
PAGE 4
3. Selecting Chip Type with make_drv Script (for compound release) Our driver source release has two types: 1) single release, which can build out driver only for single chip type, and 2) compound release, which can build out drivers for multiple chip types separately. For compound release driver, you will see make_drv script after you decompress the driver tar ball located in driver folder. Before compiling driver source, executing the make_drv to select the target chip type to compile.
PAGE 5
‘CONFIG_PLATFORM_I386_PC’ is selected by default. We can select an existing entry or add a new entry for your target platform. For example, to add and select a new entry, ‘CONFIG_PLATFORM_NEW’: CONFIG_PLATFORM_I386_PC = n CONFIG_PLATFORM_NEW = y Second, you should create and/or modify the corresponding entry inside platform setting section.
PAGE 6
l ARCH The ARCH is used to specify the architecture of the target platform CPU, such as: arm, mips, i386, etc. l CROSS_COMPILE The CROSS_COMPILE is used to specify the toolchain prefix used for driver compilation.
PAGE 7
configuration by yourself. See the following table for the autoconf file you should modify for a specific chip type: Chip type Autoconf file to modify RTL8192CU-series autoconf_rtl8192c_usb_linux.h RTL8192CE-series autoconf_rtl8192c_pci_linux.h RTL8192DU-series autoconf_rtl8192d_usb_linux.h RTL8192DE-series autoconf_rtl8192d_pci_linux.h RTL8723AS-series autoconf_rtl8723a_sdio_linux.h RTL8723AU-series autoconf_rtl8723a_usb_linux.h RTL8189ES-series autoconf_rtl8189e_sdio_linux.
PAGE 8
2). Add the following line into drivers/net/wireless/Makefile, CONFIG_RTL8192CU is for , rtl8192cu is for : obj-$(CONFIG_RTL8192CU) += rtl8192cu/ 3). Add the following line into drivers/net/wireless/Kconfig, rtl8192cu is for : source "drivers/net/wireless/rtl8192cu/Kconfig" 4). Config kernel, for example, with ‘make menuconfig’ command to select ‘y’ or ‘m’ for our driver. 5). Now, you can build kernel with ‘make’ command. 6. Compiling Driver 6.1.