` 0
Table of Contents 1. Precaution……………………….………….…… 2 2. Preparation………………………………………. 4 Components & Accessories………..………. 4 Part Names………………………………….. 5 3. Initiate SMC from Mobile Device……….……… 6 Download the SMC App..……………….….. 6 Connect to the SMC via Wireless Network.. 6 System Setting via SMC App for iOS……… 7 System Setting via SMC App for Android… 13 4. Initiate SMC from PC……….…………..……… 18 Connect to the SMC………………….…….. 18 Connect via the Wired……….……….…… 18 Connect via the Wireless………..
1 Precaution Thank you for purchasing a Monitoring Camera. Please take a moment to read through this manual. Its contents will send you on an educational journey into your recorder multiple capabilities. Before using the SMC, the Monitoring Camera, please ensure that you read and understand the safety precautions described below. Always ensure that the Monitoring Camera is operated correctly.
If you notice smoke or a strange odor coming from the Monitoring Camera, turn the power off immediately. Take the Monitoring Camera to the nearest authorized service center for repair. Never attempt to repair the Monitoring Camera on your own. Use only the recommended power accessories. Use of power sources not expressly recommended for the Monitoring Camera may lead to overheating, distortion of the equipment, fire, electrical shock or other hazards.
2.
Part Name Setup Enter the System Setting mode. Reset Restart Press the Reset key when mini USB cable connected. Default Press the Reset key and hold then plug-in the mini USB cable.
3 Initiate SMC from Mobile Device Download the SMC App SMC App is compatible with the iOS 5.0 or above and Android 2.2 or above. 1. Before using the Monitoring Camera, search and download the free App “SMC”. 2. Press INSTALL APP to install SMC in your mobile device. Connect to the SMC via wireless network 1. Connect the USB AC Adaptor with USB cable to the mini USB Port. (This mini USB port is for power supply only.) 2. The SMC launch automatic when the USB power supplied.
System Setting via SMC App (for iOS) 1. Search the SMC icon. 2. Press the SMC icon to launch it. 3. Press “Next”. 4. Please make sure that you have TM created a new Skype account for the Monitoring Camera. Press “Next” if you already have TM the Skype account for SMC. If TM not, press “Apply new SKYPE account” first to create a new account for SMC.
5. Press the “Setup” key on the bottom of the Monitoring Camera. The red LED will blink after 10 seconds. Wait about 15 seconds until the steady red LED. Then press “Next”. 6. Find the MAC Address on the Monitoring Camera then press “Next”. 7. Find the Setting of the iOS and press the “WLAN”. 8. Search the same MAC Address from the “WLAN” Setup then select it as the SSID.
9. Key-in the password and press “Connect”. (default password : 1234567890) 10. Make sure the SSID of SMC has connected then press “Return”. 11. The SMC App show this error message if the SMC SSID connect failed. Please press the “Wireless Settings” again and repeat step 7 to 10. 12. The SMC SSID has connected correctly. Press “Next”.
13. Press “Next”. 14. Appoint a wireless SSID which must can connect to the internet for the Monitoring Camera. SMC will scan available wireless SSID and show them under “Selection of SSID”. Select one of them then press “Next”. 15. Press the “Encryption Mode” to select the matched mode. 16. Enter the matched “Security Key” and confirm it again. Then press “Next”.
TM 17. Configure Skype account of the Monitoring Camera. SMC will use this account to logo in TM Skype server. TM 18. Enter Skype account and password and confirm again. 19. Press the “Advance” which allow you to revise the system status of the Monitoring Camera if needed. Press “Back” to quit the advance mode. 20. Press the “Complete setting” to finish SMC setting.
21. Press “Exit” to close SMC App.
System Setting via SMC App (for Android) 1. Search the SMC icon. 2. Press the SMC icon to launch it. 3. Press “Next”. 4. Please make sure that you have TM created a new Skype account for the Monitoring Camera. Press “Next” if you already have TM the Skype account for SMC. If TM not, press “Apply new SKYPE account” first to create a new account for SMC.
5. Press the “Setup” key on the bottom of the Monitoring Camera. The red LED will blink after 10 seconds. Wait about 15 seconds until the steady red LED. Then press “Next”. 6. Find the MAC Address on the Monitoring Camera then press “Next”. 7. Search the same MAC Address from the “WLAN” Setup then select it as the SSID. 8. Key-in the password and press “Connect”.
9. Make sure the SSID of SMC has connected then press “Return”. 10. The SMC App show this error message if the SMC SSID connect failed. Please press the “Wireless Settings” again and repeat step 7 to 9. 11. The SMC SSID has connected correctly. Press “Next”. 12. Press “Next”.
13. Appoint a Wireless SSID which must can connect to the internet for the Monitoring Camera. SMC will scan available wireless SSID and show them under “Selection of SSID”. Select one of them then press “Next”. 14. Press the “Encryption Mode” to select the matched mode. 15. Enter the matched “Security Key” and confirm it again. Then press “Next”. TM 16. Configure Skype account of the Monitoring Camera. SMC will use this account to logo in TM Skype server.
TM 17. Enter Skype account and password and confirm again. 18. Press the “Advance” which allow you to revise the system status of the Monitoring Camera if needed. Press “Back” to quit the advance mode. 19. Press the “Complete setting” to finish SMC setting. 20. Press “Exit” to close SMC App.
4 Initiate SMC from PC Connect to the SMC - Monitoring Camera Connect via the wired network 1. Connect the RJ45 port of SMC to PC / NB via a network wire. 2. Connect the USB AC Adaptor with USB cable to the mini USB Port. (This mini USB port is for power supply only.) 3. The SMC launch automatic when the USB power supplied. 4. The system will need about 15 seconds to initiate after the LED of RJ45 connecter blinking. 5. Press the Setup button. The Status LED blinking slowly with RED. 6.
7. Run the Command Prompt and enter ipconfig command to check the network status to confirm the SMC has linked with PC / NB.
Connect via the wireless network 1. Connect the USB AC Adaptor with USB cable to the mini USB Port. (This mini USB port is for power supply only.) 2. The SMC launch automatic when the USB power supplied. 3. Press the Setup button. The Status LED blinking slowly with RED. 4. The status LED stop blinking and illuminate with RED when link with the network. 5. Find the MAC Address on the SMC. 6. Search the same MAC Address from the “Networks” Setup then select it as the SSID of SMC.
7. Select the SMC SSID and connect it. 8. Enter the network security key. (default : 1234567880) 9. Confirm SMC has connected with PC / NB.
System Setting 1. Open a browser and enter IP address 192.168.1.1 then press enter. 2. Click Admin Login. Key-in admin in the Username (without password) of Admin dialog then press OK.
3. The System Setting screen appeared. 4. Select link to internet via Wired then click the check box of Enable Ethernet to enable the wired network.
Or select link to internet via Wireless and select valid wireless from the Scan List. Click the check box of Enable Wireless to enable the wireless network. 5. Press the “Submit” and finish the System Setting.
Skype TM Setting TM 1. Select General under Skype and enter the TM “Skype Setting”. TM 2. Enter Skype account and password which registered for this Monitoring Camera. TM 3. Press the “Submit” and finish the “Skype Setting”. 4. Press the “Reboot” and quit. TM Note: 1. Create a new Skype account from PC / NB before use the Monitoring Camera. 2. Add all contacts who has permitted to login TM the Skype account of Monitoring Camera.
5 Operate the SMC Connect to Internet via Wired Plug-in a network wire to the RJ45 port of the SMC. Connect the other connector of the network wire to a valid internet port. Connect to Internet Wireless Disconnect the network wire from the SMC. Standby 1. Connect the USB AC Adaptor with USB cable to the mini USB Port. (This mini USB port is for power supply only.) 2. The SMC launch automatic when the USB power supplied. 3.
Video Monitor TM TM 1. Launch the Skype and sing in with the “Skype Name” and “Password” which has added in the contact list of the SMC. 2. Click the contact of SMC you want to monitor from the contact list. Then press the ‘Video call’ button.
3. Your video window will appear on the bottom screen. 4. The SMC will answer incoming call automatically and the Status LED blinking with Green. The contact video will appear on the Video 2 screen and your video display on the Video 1 screen.
6 Appendix Specification Model No.: SMC-1 Image Sensor 1/4”, 2M (1600x1200) pixels, CMOS Lens F2.0, f=3.348 mm Focus Type Fixed Focus Focus Range 60 cm to infinity White Balance Auto Exposure Auto Video Encoder H.264 HQ Video Conference HD 720P @ 30fps Audio Input Built-in 2 Microphones Wireless IEEE 802.
Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Notice: 1. Users will automatically receive software upgrade notice when logged on to Skype account with your Skype client software on PC or mobile phone Apps. 2. Skype is a trade mark of Skype Limited or its related companies. This product / application has not TM been approved or endorsed by Skype Limited, TM Skype Communications S.a.r.l. or any of their related companies. 3. This product includes SkypeKit Version [3.
