Technical Specifications

Sakrete.com • 866-725-7383
The Pro’s Choice Since 1936
2. Scuffing, wire brushing, or sanding the surface prior to cleaning helps insure
a good bond. Care should be taken to remove all loose debris from the drilled
hole using a suitable blower or vacuum before applying.
Application:
1. For best results use a caulk gun with a minimum 12:1 mechanical power.
Inexpensive guns will not push the material through the nozzle.
2. Load the cartridge assembly into a caulking gun.
3. Unscrew the cartridge cap and remove the nozzle plug.
4. Attach the static mixer nozzle. Dispense mixed paste to waste until an
uniform color is achieved (at least 5 mL) and then directly onto the work
surface or into the pre-cleaned hole.
5. When filling holes, start from the back; be careful not to leave any air pockets
or voids while filling. Use the mixed paste within 20 minutes or insert the bolt
into the filled hole within 5 minutes of application.
Curing:
1. Cure time to ultimate hardness is 24 hours.
2. Actual cure time is affected by temperature and product amount used: higher
temperatures and larger volumes of material used cure faster.
Precautions:
• Does not adhere to PTFE, polyethylene, or polypropylene.
• For anchoring applications, concrete should be a minimum of 21 days old prior
to anchor installation.
• Not recommended for any application where there may be a sustained tensile
load, including overhead applications.
NOTE: Proper application and installation of all Sakrete products are the responsibility of the end user.
Safety:
READ and UNDERSTAND the Safety Data Sheet (SDS) before using this product.
WARNING: Wear protective clothing and equipment. For emergency information,
call CHEMTREC at 800-424-9300 or 703-527-3887 (outside USA).
KEEP OUT OF REACH OF CHILDREN.
Limited Product Warranty:
The manufacturer warrants that this product shall be of merchantable quality
when used or applied in accordance with the manufacturer’s instructions. This
product is not warranted as suitable for any purpose other than the general
purpose for which it is intended. This warranty runs for one (1) year from the
dates the product is purchased. ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO
THE DURATION OF THIS WARRANTY. Liability under this warranty is limited to
replacement or defective products or, at the manufacturer’s option, refund of the
purchase price. CONSEQUENTIAL AND INCIDENTAL DAMAGES ARE NOT RECOV-
ERABLE UNDER THIS WARRANTY.
High Strength anchoring epoxy
Sakrete
®
High Strength Anchoring Epoxy is a two-com-
ponent epoxy compound that cures to an exceptionally
strong, hard product. This unique formulation provides
an excellent balance of mixability and flow without
run-out to allow for the fastening and anchoring of both
vertical and horizontal fixtures into masonry.
Features:
• Extended working time
• Exceptionally strong and hard once cured
• Solvent-free with no volatile components
• Will not shrink upon curing
• Ready to use
Use For:
• Anchoring and bonding applications
• Grouting dowel bars for concrete repairs
• Filling holes, pits and cracks
Technical Data:
Compressive Strength - 10,000 psi (69 MPa)
Compressive Modulus - 400,000 psi (2.7 GPa)
Pullout Strength ASTM E488 - 21,500 psi (148 MPa) in 24 hours
(5/8” threaded rod 5-5/8” deep)
Color:
Gray
Preparation:
1. To achieve optimum performance, surfaces and holes should be
dust-free and cleaned of all surface contaminants, such as grease, oil, water,
or dirt.
SAKRETE
®
and the background design are registered trademarks of SAKRETE of North America LLC, Charlotte, NC 28217 • ©2006. SAKRETE
®
is manufactured under license from SAKRETE of North America LLC.
For current and complete product information, contact SAKRETE Technical Services toll-free at 866-725-7383 or visit Sakrete.com.
Rev. 07/16
Uncured Properties Results
Form Two-part paste
VOC Content 2 grams/liter
Density 11.5 lb/gal (1.38 g/cm
3
)
Mix ratio, base to curing agent 1:1
Working time at 75
O
F (24
O
C) 28 min.