Matrix Bar 12x3W Warm White Beam SG PIXI5WL MANUALE UTENTE USER MANUAL
Rev. 01-06/17 INDICE: 1. INTRODUZIONE p. 3 2. ISTRUZIONI DI SICUREZZA p. 4 3. APERTURA CONFEZIONE E CONTROLLO p. 6 4. INSTALLAZIONE ED ACCENSIONE p. 7 5. ISTRUZIONI PER L'USO p. 9 6. ACCOPPIANENTO p. 11 7. MANUTENZIONE p. 12 8. SPECIFICHE TECNICHE p. 12 INDEX: 1. INTRODUCTION p. 13 2. SAFETY INSTRUCTIONS p. 14 3. OPENING AND CONTROL p. 16 4. INSTALLATION AND SWITCH ON p. 17 5. SETUP p. 19 6. COMBINATION p. 21 7. MAINTENANCE p. 22 8. TECHNICAL SPECIFICATIONS p.
1. INTRODUZIONE Grazie per avere scelto un nostro prodotto! Vi preghiamo di fare riferimento alle istruzioni e alle avvertenze contenute nel presente manuale per l’utilizzo del dispositivo e di conservarlo per future consultazioni. Il presente manuale contiene informazioni riguardanti l’installazione e l’utilizzo del dispositivo. Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze.
2. ISTRUZIONI DI SICUREZZA Attenzione! Questo prodotto non è adatto ad un uso domestico. Leggere il presente manuale prima di installare e dare corrente all’apparecchiatura, seguire le precauzioni di sicurezza elencate di seguito ed osservare tutti gli avvertimenti indicati nel presente manuale e stampati sull’apparecchiatura. Si prega di contattare un distributore PROEL per ricevere assistenza riguardo qualsiasi dubbio su come attivare l’apparecchiatura in modo sicuro.
CLASSE DI PROTEZIONE IP20 Il dispositivo è protetto contro la penetrazione di corpi solidi di dimensioni superiori a 12 mm (0.47”) di diametro (prima cifra 2), ma non contro la caduta di gocce d’acqua, pioggia, schizzi o getti d’acqua (seconda cifra 0). Usare solo in ambienti asciutti. Usare solo all’interno. Non esporre l’apparecchiatura a pioggia o ad umidità. PROTEZIONE CONTRO LE SCOSSE ELETTRICHE Il dispositivo deve essere collegato ad un sistema di alimentazione dotato di un’efficiente messa a terra.
3. APERTURA DELLA CONFEZIONE E CONTROLLO Aprire con cura la confezione, verificare il contenuto e assicurarsi che tutte le parti siano presenti e siano in buone condizioni. Nel caso in cui alcune parti non siano presenti o siano danneggiate, contattare immediatamente il proprio fornitore e conservare l’imballaggio per la verifica. ATTENZIONE! Se l'apparecchio è stato esposto a drastici sbalzi di temperatura, lasciare spenta l'unità finché non raggiunge la temperatura ambiente.
4. - INSTALLAZIONE ED ACCENSIONE 4.1 - INSTALLAZIONE PRODOTTO - Non scuotere l'apparecchio. Evitare l'utilizzo di forza eccessiva durante le operazioni di installazione o fissaggio dell'unità. - L'unità deve essere installata SINGOLARMENTE a parete, a soffitto o su truss. La staffa inclusa non è infatti progettata per sospendere una intera colonna, ma solo un singolo elemento. Ogni singola unità deve essere ancorato tramite l’apposita staffa corta inclusa.
4.2 - COLLEGAMENTO ALLA LINEA DI ALIMENTAZIONE Il dispositivo deve essere collegato ad un sistema di alimentazione dotato di un’efficiente messa a terra. Inoltre, si consiglia di proteggere le linee di alimentazione dei prodotti dai contatti indiretti e/o da cortocircuiti verso massa utilizzando interruttori differenziali opportunamente dimensionati. Il collegamento alla rete elettrica deve essere effettuato da un installatore elettrotecnico qualificato.
5. - ISTRUZIONI PER L'UTILIZZO 5.1 - MAPPA DEL MENU' DMX CHANNEL 002 Modalità 2 canali CHANNEL 003 Modalità 3 canali CHANNEL 006 Modalità 6 canali CHANNEL 012 Modalità 12 canali ADDRESS (001 – 512) RUN MODE 001 – 512 DMX Modalità DMX SLAVE Modalità Slave ID NUMBER OFF, 001 - 066 Indirizzo ID DISPLAY LED ON - OFF Retroilluminazione display OFF = spegnimento dopo circa 30s ON = sempre acceso KEY LOCKS ON - OFF Blocco pulsantiera.
5.
MODALITA’ 4: 12 canali DMX Canale DMX 1 2 3 4 5 6 7 8 9 10 11 12 Valore 000 – 255 000 – 255 000 – 255 000 – 255 000 – 255 000 – 255 000 – 255 000 – 255 000 – 255 000 – 255 000 – 255 000 – 255 Funzione Dimmer LED 1 Dimmer LED 2 Dimmer LED 3 Dimmer LED 4 Dimmer LED 5 Dimmer LED 6 Dimmer LED 7 Dimmer LED 8 Dimmer LED 9 Dimmer LED 10 Dimmer LED 11 Dimmer LED 12 6. – ACCOPPIAMENTO 1. Accostare 2 pezzi sullo stesso piano ed allineare i fori 2.
7. - MANUTENZIONE Per garantire ottime prestazioni, l’apparecchio deve essere pulito frequentemente. Scollegare l’apparecchio della corrente e lasciarlo raffreddare per almeno 35 minuti onde evitare il rischio di bruciature. Utilizzare un aspirapolvere o compressore e una spazzola morbida o un panno per lenti per rimuovere la polvere depositata. Le lenti, come qualsiasi altra parte eventualmente danneggiata, devono essere sostituite con ricambi originali. 8.
1. - INTRODUCTION Thank You for choosing one of Our products! Please refer to the instructions and warnings contained in this user manual, please retain it for future reference. This manual contains information about the installation and use of the device. The information contained in this publication has been carefully prepared and checked. However it is not assumed any responsibility for any inaccuracies.
2. - SAFETY INSTRUCTIONS Caution! This product is not suitable for household illumination. Please read this manual before installing and applying power to the equipment, follow the safety precautions listed below and observe all warnings in this manual and printed on. Please contact a PROEL distributor for assistance with any questions about how to activate the equipment safely. Contact a qualified technician for any maintenance work not described in this manual.
IP20 PROTECTION RATING The device is protected against the penetration of solid bodies larger than 12 mm (0,47 ") in diameter (first digit 2), but not against dripping water, rain, splashes or jets of water (second digit 0). Use only in dry areas. Inside use only. Do not expose the equipment to rain or moisture. PROTECTION AGAIN ELECTRIC SHOCK The device must be connected to a power supply system with efficient earthing.
3. - OPENING AND CONTROL Carefully open the package, check the content and make sure that all the parts are present and are in good condition. In cases where some parts are not present or are damaged, immediately contact Your supplier and retain the packaging for verification. WARNING! If the product has been exposed to drastic temperature changes, let the unit turned off until it reaches room temperature because the presence of condensation can damage the product if it is turned on.
4. - INSTALLATION AND SWITCH ON 4.1 - PRODUCT INSTALLATION - Do not shake the device. Avoid the use of too much force during installation or unit fixing. - Each unit must be installed singly on a wall, on a ceiling or on a truss. In case of a ceiling suspension or truss suspension it is not possible to use the included brackets, if you plan to create a matrix of panels, in this case the first row of the matrix must be suspended with a specific metal bar (sold separately).
4.2 - CONNECTION TO THE MAINS The device must be connected to a power supply system with a proper earth system. Moreover, it is recommended to protect power supply lines of the products from indirect contact and / or shorting to earth by using appropriately sized anti electrical shock switch. The electrical connection must be carried out by a qualified electrician. Ensure that the mains frequency and voltage correspond to those for which the device is designed, as shown in the electrical data label. 4.
5. - SETUP 5.1 – MENU DMX CHANNEL 002 2 channels mode CHANNEL 003 3 channels mode CHANNEL 006 6 channels mode CHANNEL 012 12 channels mode ADDRESS (001 – 512) RUN MODE 001 – 512 DMX DMX mode SLAVE Slave mode ID NUMBER OFF, 001 - 066 ID address DISPLAY LED ON - OFF Display backlight OFF = switch off after 30s ON = always ON KEY LOCKS ON - OFF Keypad lock.
5.
MODE 4: 12 DMX channels DMX channel 1 2 3 4 5 6 7 8 9 10 11 12 Value 000 – 255 000 – 255 000 – 255 000 – 255 000 – 255 000 – 255 000 – 255 000 – 255 000 – 255 000 – 255 000 – 255 000 – 255 Function Dimmer LED 1 Dimmer LED 2 Dimmer LED 3 Dimmer LED 4 Dimmer LED 5 Dimmer LED 6 Dimmer LED 7 Dimmer LED 8 Dimmer LED 9 Dimmer LED 10 Dimmer LED 11 Dimmer LED 12 6. – COMBINATION 1. Put 2 pcs on the same plane 2. Press the quick lock, then rotate 90 degrees.
7. - MAINTENANCE To ensure optimal performance, the unit must be frequently cleaned. Unplug the device from the mains and let it cool for at least 35 minutes to avoid the risk of burns. Use a vacuum cleaner or an air compressor and a soft brush or a lens cloth to remove the dust deposited. The lenses, like any other damaged part, must be replaced with original spare parts. 8.
Proel S.p.A. Via alla Ruenia 37/43 64027 Sant'Omero (TE) ITALY Tel. +39 0861 81241 Fax. +39 0861 887862 Mail: info@proel.com Web: www.proel.