Parts and Accessories List

ManualsBrandsSAFETYWALK ManualsElectronicsC360

Table Of Contents

Parts & AccessoriesParts & Accessories InstallationInstallation

• The front transmitter should be located on the front passenger most portion

of the vehicle. The rear transmitter

should be mounted to the rear passenger most portion of the vehicle.

• Find a suitable, ﬂat mounting location for the transmitters.

• Mounting of the transmitters can be accomplished with screws or with the

pre-attached adhesive.

1 2 3

1. Receiver 2. Transmitter (Front) 3. Transmitter (Rear)

Pair ( Pairing Paired)

Front transmitter ( No detection Detected)

Rear transmitter ( No detection Detected)

YY/MM/DD

HH: MM

Time setting: UP / Serial Code

Time setting: DOWN

Time setting mode

Plug in with USB Drive for

Downloading Record

Downloading idicator

Downloading

Done

Open

Open to :

replace battery

pair with receiver

Push to close Safety Walk

Push & hold for 10 seconds

to skip other transmitter in

case its battery is low or it’s lost

For replacing battery :

The receiver will start to voice alarm when battery is low

Open the battery door anti-clockwise

Replace the 2pcs CR2032 batteries by having the “+”

polarity facing upward

Close the battery door clockwise

Batteries may leak harmful liquids or explode causing injury or damage.

- Do not dispose of the batteries in ﬁre, it may cause explosion.

- Do not mix old and new or other types of battery.

- Replace all the batteries at the same time.

• This method of attachments should be accomplished in temperatures

above 60 degrees. Warming the mounting surface of the vehicle will assist

with proper adhesion.

• Clean the mounting surface area on the vehicle with alcohol.

• Remove the protective covering from the adhesive backing on the

transmitter. DO NOT touch the adhesive backing or the mounting surface.

• Find the appropriate location for the transmitter. Hold the transmitter

housing against the cleaned mounting surface. Apply even pressure for 30

seconds to ensure proper adhesion.

Installation

• To attach the transmitters with screws, remove the slotted battery cover.

Locate two screws directly above and below the batter holder. Removing

the two screws will allow the back mounting plate to release from the

transmitter.

• Locate the desired area to mount the transmitter. Using the mounting

plate, mark and predrill the two mounting holes.

• Mount the plate using screws. Reattach the transmitter to the mounting

plate using the two screws previously removed in battery compartment.

• Install Two 2032 batteries into each transmitter. The batteries are

located under the slotted cover. Rotate the slotted cover counter

clockwise.

• The vehicle MUST be in the off position. Failure to follow this direction will

cause the C360 to not function properly.

• Find a suitable location to mount the C360 receiver in the operating cabin

of the vehicle.

• Mount the C360 receiver using the screws supplied, or double sided

emblem adhesive tape. Please clean the mounting area with alcohol if using

an adhesive.

• Set time and date

OBD II

Connector

• Once the C360 receiver is mounted, connect the

OBD II connector to the vehicles OBD II port, two

lights will illuminate red.

• Allow the C360 receiver to calibrate for 30 seconds

before starting the vehicle.

Installation

PAIR

FRONT

REAR

PAIR

FRONT

REAR

For mounting using the adhesive backed mounting plate:

For Mounting with Screws:

Installation of the C360 Receiver.

DOWN

SET

DOWN

SET

1. Press to set adjusting mode

2. Press it again to move to the numbers need to change

3. Press the or to adjust the number

4. Press to close the set mode when done with adjusting

Installation of C360 Transmitters.

Use’s Manual

User’s Instruction

1516 Meadow Rd

Grand Island, NE 68803 US

Safety Walk 360 LLC

www.safetywalk360.com

Made in China

CALIFORNIA PROPOSITION 65 WARNING :

THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE STATE

OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR

OTHER REPRODUCTIVE HARM.

• A safety walk is a routine process requested for vehicle driver to check the

safety status all around the vehicle before drive away, when doing this, both the

front and rear Transmitters need to be pressed.

• Do safety walk before vehicle is ignited, or, the reminding alarm will be

triggered, until that C360 safety walk is done, with both Front & Rear

transmitter pressed. The indicator on both the Transmitter and Receiver will be

glowing in green when successfully connected.

• Pull away within 3 min after safety walk, a delayed driving will trigger the

alarm again to remind another safety walk.

• An idling parking of over 4 min will also be requested to do a safety walk

before pull away.

• An ignorance of the alarm will be recorded as violation.

Download the RecordUser’s Instruction

How to pair a new / replacing Transmitter with the receiver.

• Release the buttons, the indicator on the Transmitter will turn off, pairing is

done.

• Open the USB cover on the side of Receiver, ﬁnd the

pairing button on its left side (The same button for

downing switch)

• Open the battery door of the Transmitter, slide the

switch to “F” or “R” to position the Transmitter to the front

or rear of vehicle. It will over-wright the other one if both

are switched to “F” or “R”

• Find the pairing button beside the slide switch within the

Transmitter’s battery compartment

• Press BOTH the buttons on the Receiver and

Transmitter at the same time, the pairing indicator on the

Receiver will glow red when pairing triggered

• Hold BOTH the buttons the pairing is ongoing, till the indicators on both

Receiver and Transmitter glow green simultaneously, and the pairing indicator

on the Receiver turned off

• Your Transmitters have already been paired with the Receiver, unless it’s a

newly added one, or replacing to the original one, the following process will

be needed to pair it with your trasmitter:

C360 safety walk instruction. How to download the record.

• A C360 has a built-in ROM that can save 2000 driving records, after the

storage is full, new record will be stored to overwrite the previous oldest ones.

• The stored record can be downloaded by simply plug-in a USB drive, with a

single push of button, the records will be downloaded and stored within the

USB drive, and is readable in all systems.

1. Plug in the USB drive

2. After seeing the red indicator on, push the

button

3. You’ll see the red ﬂashes, that indicates the

download is ongoing

4. When the indicator turns green, the

download is done, just pull off the USB drive.

• The downloaded records are stored in .TXT format, that is readable in all

computer systems

Summary of content (2 pages)

PAGE 1
Installation Parts & Accessories Installation Installation of C360 Transmitters. Plug in with USB Drive for Downloading Record 1 2 3 OBD II Connector • This method of attachments should be accomplished in temperatures above 60 degrees. Warming the mounting surface of the vehicle will assist with proper adhesion. • Clean the mounting surface area on the vehicle with alcohol. • Remove the protective covering from the adhesive backing on the transmitter.
PAGE 2
FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.