User's Manual

ManualsBrandsSafety Technology International ManualsElectronicsRemote Control

Page 1

Installation and Operation Manual

STI 8 Channel Wireless Monitor

Model: STI-34108

Thank you for purchasing this fine product. We want you to know that your satisfaction is very

important to us. We suggest you take the time to read this manual carefully to get the most from

your new product.

HOW THE PRODUCT WORKS

STI offers multiple wireless products designed to alert you of several different conditions. The

STI 8 CHANNEL WIRELESS MONITOR allows you to monitor up to 8 different STI devices

at a single convenient location. When placed in Enroll Mode, it allows you to select 1 of 8

different zones that will represent your STI device(s) best, and enrolls it when the monitor

detects the STI device's wireless signal. The STI wireless device family uses a system that also

ensures other devices that are not from STI will not get enrolled or detected. So there are no

concerns about accidental enrollment, alerts or crosstalk. The STI 8 CHANNEL WIRELESS

MONITOR allows you to select turning on a siren, sounding a chime, triggering a normally open

or normally closed switch, or turning on an external 12 VDC output. It also allows you to

choose which devices shall have latching, when selected during enrollment.

The STI 8 Channels Wireless Monitor also acts as a repeater when paired with other STI 8

CHANNEL WIRELESS MONITORS to receive wireless transmissions over long distances or

around disruptive terrain.

Summary of content (12 pages)

PAGE 1
Installation and Operation Manual STI 8 Channel Wireless MonitorTM Model: STI-34108 Thank you for purchasing this fine product. We want you to know that your satisfaction is very important to us. We suggest you take the time to read this manual carefully to get the most from your new product. HOW THE PRODUCT WORKS STI offers multiple wireless products designed to alert you of several different conditions.
PAGE 2
BEFORE YOU START Refer to these drawings to become familiar with all the parts.
PAGE 3
Switch, Indicator and Plug Descriptions: DIP Switches (1-8) - The following information is written on the receiver. Below is a description of the DIP switch usage.
PAGE 4
Push Button - Selects zone to enroll or delete, acknowledge latched alert (resets LED to GREEN), silences alarm. LEDs (1-8) - Each enrolled sensor or mirrored receiver has an LED that indicates the current state of that zone from the top LED (Zone 1) down to the bottom LED (Zone 8).
PAGE 5
INSTALLATION GUIDE Surface Installation: 1. Ensure mounting screws are removed. 2. Insert rubber feet (provided) into holes on bottom cover 3. Route wires under the product. If using for the first time or for enrollment adjustments, follow Zone Enrolling instructions. Otherwise, STI 8 CHANNEL WIRELESS MONITOR should be fully functional. Wall Mounted Installation: 1. Ensure rubber feet are removed 2. Remove front cover screw 3. Remove cover (be careful not to lose push button) 4.
PAGE 6
OPERATING INSTRUCTIONS Zone Enrolling: The STI 8 Channel Receiver is designed to receive ONLY wireless signals from products in the STI Wireless Family of Products (See Back of the Installation Instructions). The STI 8 Channel Receiver allows you to enroll up to 8 devices into zones 1 thru 8 of the receiver. The STI 8 Channel Receiver will enroll from the different sensors directly or by enrolling other mirrored STI 8 Channel Receivers. The STI 8 Channel Receiver also enrolls up to 2 keyfobs.
PAGE 7
the sensor. Then, mount the sensor at its intended location and trigger an alert on the sensor. Check that the zone on the STI 8 CHANNEL WIRELESS MONITOR to see it is continuous RED or flashing RED, which means it received the sensor's signal. Then, if latching is not desired, delete that zone (see Zone Deleting) and enroll the sensor again without latching, DIP SW3 (OFF), from it mounted location. Enrolling Mirrored (multiple) Receivers: 1. First check that the module is not in DELETE mode, DIP SW7 (OFF).
PAGE 8
Zone Deleting: Sensors or Mirrored Receivers: 1. Enter DELETE mode, DIP SW7 (ON). All enrolled zone LEDs will turn RED. 2. The first zone to be deleted will have the LED flashing RED. 3. Press and release the push button to cycle the flashing LED through the zones until it reaches the zone to be deleted. 4. To delete a single zone, press and hold the push button to delete the zone with the flashing LED for 3 seconds. The receiver will give a single beep and the LED will turn off. 5.
PAGE 9
BASIC OPERATION The STI 8 CHANNEL WIRELESS MONITOR receives 433 MHz radio signals from numerous STI brand sensor types enrolled to one of 8 zones on the monitor. It provides feedback to the user in the form of LED colors, onboard sounder annunciation, onboard sounder siren, switched on or off output terminals (Form C contacts), a 3 second 12 VDC @ 75mA max. output on the Triggered Output Plug, and 12 VDC output terminals that are powered at the same time as the onboard sounder.
PAGE 10
Sensor Operation: A sensor sends a 433 MHz radio signal to the receiver that will indicate one or more of the following: Alert Triggered; Restored To Normal; Sensor Tampering; Low Battery; Lost Signal Mirrored Receiver Operation: The LEDs, the sounder, the siren time and the 12VDC output will duplicate the sensor settings as they are enrolled on the Master Receiver. If LED "latching" is desired on the mirrored receiver, this must be selected at the time of the mirrored receiver's enrollment.
PAGE 11
IMPORTANT NOTICE: This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications.
PAGE 12
When using lamp controller option, use ONLY 200 Watt or less incandescent lamps, and keep lamp away from bed coverings, curtains or other flammable materials as this may present a fire hazard. WARRANTY INFORMATION: Safety Technology International, Inc. warrants to the original consumer/purchaser that this product shall be free of defects in material and workmanship under normal use and circumstances for a period of one (1) year from the original date of purchase.