User's Manual

INSTALLATION OF STI-34071 STI Wireless Conversion Board
All specifications and information shown were current as of publication and are subject to change without notice.
34071 OCT2010
®
Safety Technology International, Inc.
2306 Airport Road • Waterford, Michigan 48327-1209
Phone: [phone] • Fax: [phone]
Toll Free: 800-888-4784 • E-mail: [e-mail]
Web: www.sti-usa.com
Safety Technology International (Europe) Ltd.
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England • Tel: [phone]
Fax: [phone] • Freephone: 0800 085 1678 (UK only)
E-mail: [e-mail] • Web: www.sti-europe.com
INSTALLATION INSTRUCTIONS
1. Remove Cover.
2. Disconnect 9V battery.
3. Remove the reed sensor from its internal mounting location so that it hangs freely.
4. Keeping the reed sensor wires inward, insert the STI WIRELESS RETRO PCB legs into the PCB mounting slots.
Make sure the onboard 9V connector is facing inward towards the horn.
5. Connect the “NC” and “Com” wires on the STI WIRELESS RETRO PCB to the Stopper “NC” and “Com” terminals.
(If using externally fed +12VDC power, also connect “GD” and “V+” wires to those Stopper terminals.)
6. Reattach the reed sensor to the internal mounting location being careful not to pull out a connection on
the Stopper terminals.
7. Connect the Stopper’s 9V connector to the STI WIRELESS RETRO PCB’s onboard 9V connector.
8. Connect the STI WIRELESS RETRO PCB’s wired 9V Connector to the 9V Battery.
9. Replace cover and screws.
IMPORTANT NOTICE:
Changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate this equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may be received, including interference that
may cause undesired operation.
Model: 34071
FCC ID: TXL34071
IC: 6335A-34071
This product meets the applicable Industry Canada technical specifications.
Le présent materiel est conforme aux specifications techniques applicables d’Industrie Canada.
TO USE WIRELESS SIGNAL WITHOUT AUDIBLE ANNUNCIATION
1. Follow standard installation steps.
2. Connect an additional reed switch connections into “NC” and “COM” on the Stopper
terminals with the wires from the STI WIRELESS RETRO PCB.
3. Install the additional reed switch on top of the reed switch connected to the “RS1” Stopper
terminal. Use tape to hold the 2 reed switches together.
WIRELESS OPERATION:
The STI WIRELESS RETRO PCB will send a wireless signal to an STI 433MHz 4 Channel Receiver
or 8 Channel Receiver. The STI WIRELESS RETRO PCB sends an Alert signal when the “NC”
switch is opened. It sends a Restore-To-Normal signal when the switch is closed.
NOTE: To enroll the wireless device signal into the receiver, please see the receiver installation
instructions.
JP5
JP2
JP4
JP3
JP7
SWITCH
ALARM
DURATION
ALARM VOLUME SWITCH
TRIP DELAY SWITCH
ARMING SWITCH
(FACTORY DEFAULT SETTINGS)
(ON)
(ON)
(OFF)
(OFF)
(OFF)
TERMINAL BLOCK
FOR COMPLETE ALARM OPTIONS
AND SWITCH SETTINGS SEE CHART
ON REVERSE SIDE.
PC BOARD
JP5
JP2
JP4
JP3
SWITCH
ALARM
DURATION
ALARM VOLUME SWITCH
TRIP DELAY SWITCH
ARMING SWITCH
(
FACTORY DEFAULT SETTINGS
(FACTORY DEFAULT SETTINGS)
(ON)
(ON)
(OFF)
(OFF)
(OFF)
WIRES FROM RETRO PCB
TO 9V BATTERY
WIRES FROM STOPPER PCB
TO RETRO PCB
BLUE “NC” WIRE
GREEN “COM” WIRE
WIRELESS TRANSMITTER PCB
EXIT ALARM
BASE ASSEMBLY