CFIP PhoeniX Series TDM/IP Split Mount System Technical Description & Configuration Guide SAF Tehnika JSC 2015 The CFIP Series Full Outdoor Unit Technical Description and Configuration Guide • Rev. 1.
Proprietary notice The information presented in this guide is the property of SAF Tehnika, JSC. No part of this document may be reproduced or transmitted without proper permission from SAF Tehnika, JSC. The specifications or information contained in this document are subject to change without notice due to continuing introduction of design improvements. If there is any conflict between this document and compliance statements, the latter will supersede this document.
Table of Contents 1 Overview ................................................................................................................................... 4 1.1 CFIP PhoeniX TDM/IP split mount system ...................................................................................... 4 1.2 CFIP PhoeniX feature Summary ...................................................................................................... 5 1.2.1 1.2.2 1.3 1.4 1.4.1 Main Features ....................................
Proprietary notice The information presented in this guide is the property of SAF Tehnika, JSC. No part of this document may be reproduced or transmitted without proper permission from SAF Tehnika, JSC. The specifications or information contained in this document are subject to change without notice due to continuing introduction of design improvements. If there is any conflict between this document and compliance statements, the latter will supersede this document.
1.2 CFIP PhoeniX feature Summary 1.2.1 Main Features • Split mount system solution • Capacity: up to 363 Mbps • Channel Bandwidth: 3.5 / 7 / 14 / 28 / 40 / 56 MHz • Modulations: 4QAM / 16QAM / 32QAM / 64QAM / 128QAM / 256QAM 1.2.2 ODU mechanical features • Compact unit, 285x285x80mm, 3.
1.4 Technical specification CFIP PhoeniX ODU General Band 5.8 GHz Form factor IDU – ODU split-mount Antenna External Tx-Rx architecture FDD RF Frequency range 5725 – 5850 MHz Max Tx power +27 dBm Max channel bandwidth 30 MHz Supported modulations QPSK/4QAM, 16QAM, 32QAM, 64QAM, 128QAM, 256QAM Duplex offset 95MHz Ports Antenna N-Type IF to IDU N-Type RSSI BNC Mechanical & Electrical Operational use Conforms to ETSI EN 300 019 Class 4.
Figure 1.3 CFIP PhoeniX IDU-ODU cable RSSI BNC To connect the digital multimeter to the CFIP PhoeniX ODU RSSI port in order to adjust the antenna alignment, a coaxial cable with BNC connector on one end and appropriate termination on other end can be used (see example in Figure 1.4). Figure 1.4 Cable for connecting the voltmeter to the CFIP PhoeniX ODU RSSI port 1.6 Labelling The label contains the following information (see samples in the picture below): - Model name.
Figure 1.5 Label of the CFIP PhoeniX ODU Low band side, operating in 5.8 GHz band P/N Translation for CFIP PhoeniX ODU: - “S” designates CFIP split mount series product; - “06” designates Frequency range (5.8 GHz) of the Unit; - “RP” designates high power radio; - “R” designates ODU operating 10 - 40MHz; - “18” designates the version number of the Unit; - “L” designates the band side in which ODU operates (H, L).
(!) It is the installer’s responsibility to ensure compliance with the governing rules and regulations regarding output power and point-to-point installation and operation. Quite a few other documents specify or refer to exposure limits comparable to those given above, e.g.
2 RSSI Port RSSI (Received Signal Strength Indicator) port is used to adjust the alignment of antenna for best performance (for both rough and fine adjustment); this can be done using digital multimeter which is connected to the RSSI port. The output of the RSSI port is DC voltage and varies depending on received signal level. The following chart and table shows typical relationship of the received signal level (Rx level) displayed by CFIP vs.
3 Available Accessories Surge protection Surge Protection with gas tube P/N: CLALA001 P/N: CLALA003 CFIP ODU Mounting Bracket Flexible Waveguide UBR-PBR (for 1xODU P/N: CLGRFB05; for 2xODU P/N: CLGRFB06) (See the list of available test equipment below) 3.1 Other Available Accessories CFIP Test Equipment P/N C06TST02 Name: Test equipment 6 GHz Description Test equipment 6 GHz CFIP PhoeniX 5.8 Technical Description and Configuration Guide • Rev. 1.
4 SAF Tehnika JSC Contacts SAF Tehnika JSC technical support can be reached by: - Email: techsupport@saftehnika.com - Telephone: +371 67046840 - Fax: +371 67046809 CFIP PhoeniX 5.8 Technical Description and Configuration Guide • Rev. 1.