User's Manual

ManualsBrandsS and C Electric ManualsElectronicsS&C Wi-Fi/GPS

Wi-Fi/GPS Unit Model Number 005-004701-01

May 26, 2020

Instruction Sheet 766-527LD

Wi-Fi Admin User Manual

Table of Contents

Section Page Section Page

Introduction

Qualified Persons ........................... 2

Read this Instruction Sheet ................... 2

Retain this Instruction Sheet. . . . . . . . . . . . . . . . . . . 2

Proper Application .......................... 2

Special Warranty Provisions ................... 2

Safety Information

Understanding Safety-Alert Messages ........... 4

Following Safety Instructions .................. 4

Replacement Instructions and Labels ........... 4

Safety Precautions ......................... 5

Specification

Technical Specification ....................... 6

Antenna Specification ........................ 7

Wi-Fi Administration

Connecting to the IntelliRupter® Fault Interrupter, 6800

Series Automatic Switch Control, or IntelliCap® 2000

Automatic Capacitor Control. ................ 8

General Status .............................11

Settings .................................. 12

Interfaces ................................ 14

Security .................................. 17

User Roles ............................... 18

Diagnostics ............................... 19

Profile ................................... 20

Wi-Fi/GPS Unit

Configuration ............................. 21

Wi-Fi/GPS Unit Connectors

Interface Pinouts ........................... 22

Regulatory Information

Regulatory Notices ......................... 24

Contacting S&C Electric Company ............. 25

These instructions are for IntelliRupter fault interrupters, 6800 Series Automatic Switch Controls,

and IntelliCap 2000 Automatic Capacitor Controls shipped after May 1, 2020, with Wi-Fi/GPS Unit

model number 005-004701-01.

Summary of content (25 pages)

PAGE 1
Wi-Fi/GPS Unit Model Number 005-004701-01 Wi-Fi Admin User Manual Table of Contents Section Page Introduction Qualified Persons. . . . . . . . . . . . . . . . . . . . . . . . . . . . Read this Instruction Sheet . . . . . . . . . . . . . . . . . . . . Retain this Instruction Sheet. . . . . . . . . . . . . . . . . . . Proper Application . . . . . . . . . . . . . . . . . . . . . . . . . . . Special Warranty Provisions. . . . . . .
PAGE 2
Introduction Qualified Persons WARNING Only qualified persons who are knowledgeable in the installation, operation, and maintenance of distribution fusing equipment, along with all associated hazards, may install, operate, and maintain the equipment covered by this publication.
PAGE 3
Introduction Replacement parts provided by the seller or repairs performed by the seller under the warranty for the original equipment will be covered by the above special warranty provision for its duration. Replacement parts purchased separately will be covered by the above special warranty provision.
PAGE 4
Safety Information Understanding Safety-Alert Messages Several types of safety-alert messages may appear throughout this instruction sheet and on labels attached to crate, packing, and equipment. Become familiar with these types of messages and the importance of these various signal words: DANGER “DANGER” identifies the most serious and immediate hazards that will likely result in serious personal injury or death if instructions, including recommended precautions, are not followed.
PAGE 5
Safety Precautions DANGER IntelliRupter PulseCloser Fault Interrupters operate at high voltage. Failure to observe the precautions below will result in serious personal injury or death. The S&C 6800 Series Automatic Switch Control and IntelliCap 2000 Automatic Capacitor Control line voltage input range is 93 to 276 Vac. Failure to observe the precautions below will result in serious personal injury or death. Some of these precautions may differ from your company’s operating procedures and rules.
PAGE 6
Specification Technical Specification Table 1. Technical Specification Wi-Fi IEEE 802.11 b/g/n (2.4 GHz) WPA2-PSK Security GPS GPS/GNSS 1 PPS synchronized to UTC time Time management NTP IEEE 1588 PTP Ethernet Two 10/100 Base-T Ethernet ports with RJ45 connectors USB USB 2.0 interface with Type A connector Serial One One One One Networking Configurable network interfaces assigned to LAN or WAN Ethernet IEEE 802.3, 802.
PAGE 7
Specification Antenna Specification The Wi-Fi/GPS Unit is professionally installed equipment. The radio frequency (RF) output power does not exceed the maximum limit allowed in the country of operation. CAUTION Unauthorized antennae, modifications, or attachments may damage the device and potentially violate regulations. Note: Use only the supplied or an equivalent replacement antenna.
PAGE 8
Wi-Fi Administration Connecting to the IntelliRupter® Fault Interrupter 6800 Switch Control or IntelliCap 2000 Capacitor Control. Follow these steps to open the Wi-Fi Configuration screens in the Wi-Fi/GPS Unit (model number 005-004701-01): STEP 1. In the Windows® 10 Start menu select the Start>Programs>S&C Electric>LinkStart>LinkStart V4 option. The LinkStart Main screen will open. See Figure 1. Figure 1. The LinkStart Main screen. STEP 2.
PAGE 9
Wi-Fi Administration When connection is established, the status bar indicates “Connection Successful” and displays a solid green bar. The vertical bar graph indicates signal strength of the Wi-Fi connection. See Figure 3. Figure 3. Successful connection to the IntelliRupter fault interrupter. STEP 3. Open the Tools menu and click on the Wi-Fi Administration option. See Figure 4. Figure 4. The Wi-Fi Administration entry on the Tools menu.
PAGE 10
Wi-Fi Administration Login T he L og in screen open s w it h a u ser n a me a nd pa s sword ch a l lenge. S ee Figure 5. These screens are displayed in the Internet browser on the computer. The supported browser versions include Google Chrome and Internet Explorer. The IP address is displayed at the top of the screen and is supplied by the Wi-Fi/GPS Unit. STEP 4. Enter your username and password and click on the Login button. Authentication status is displayed.
PAGE 11
Wi-Fi Administration General Status STEP 5. To skip this screen and keep the default password setting, click on an entry in the left menu. Figures 7 and 8 on page 11 show the General Status screen. The General Status screen is informational and only displays data; no edits are allowed. Field edits are permitted in the respective menu sections where each field is defined. Figure 7. The top of the General Status screen. Figure 8. The bottom of the General Status screen.
PAGE 12
Wi-Fi Administration Settings Click on the Settings entry in the left menu to open the Settings screen. See Figure 9. Figure 9. The System Name and Firmware Upgrade panels on the Settings screen. The Settings screen contains the System Name, Firmware Upgrade, Configuration, and Reboot panels. NOTICE When a field edit is typed, the Save button becomes green and must be clicked for the new entry to be saved. System Name Enter a user-defined name for the Host Name setting and click on the Save button.
PAGE 13
Wi-Fi Administration Configuration Files The Wi-Fi/GPS Unit can perform bulk imports and exports of specific configuration data parameters. The same XML file format is used for both import and export functions. This allows a user to configure settings in one device, export those settings into an XML file (the extension is “.json”), and import the same settings into another unit.
PAGE 14
Wi-Fi Administration Interfaces Figure 11. The default Interfaces screen. Ethernet 1 (To Control Module) In this panel, the network associated with the Wi-Fi/GPS Unit local area network (LAN) is defined for devices connecting to physical Ethernet Port 1. See Figure 11. The S&C Wi-Fi/GPS Unit ships with a default IP address of 192.168.1.1 and a Netmask equal to 255.255.255.0.
PAGE 15
Wi-Fi Administration Figure 12. The Interfaces screen with the DHCP client disabled. Figure 13. The Interfaces screen with the DHCP client disabled and the DHCP server enabled. DHCP Server State “On” When the DHCP client is disabled, the DHCP server can be enabled. This allows the Wi-Fi/ GPS Unit to automatically provide an IP address to an attached device, such as a field area network radio. See Figure 13.
PAGE 16
Wi-Fi Administration The Wi-Fi Session Timeout field determines the time after which the session will automatically terminate activity through the connections. The Mode setting selects the preferred Wi-Fi transmission standard (Default: N). The Channel setpoint can be set to a channel with less traffic. The Width setpoint is the channel bandwidth in MHz. This setting is only relevant when 802.11n is chosen for the Mode setting. If 802.11b or 802.11g is elected it will be ignored. Figure 14.
PAGE 17
Wi-Fi Administration Security Figure 15. The Security screen. Remote Web Access To access the user interface for Wi-Fi Administration through the field area network, set the Remote Web Access setpoint to “on.” Note: The Remote Web Access setpoint is not available until the default admin password is changed and remote access requires the field area network to be routed through the Wi-Fi/GPS Unit. Refer to the “Configuration” section on page 21 for more details.
PAGE 18
Wi-Fi Administration User Roles The User Roles screen permits adding and editing users and their access privileges. The types of user roles include Admin, Engineer 1, Technician 1, and Viewer. The addition of a user is initiated by clicking on the Add User button. A dialogue box opens with the required User, Password, and Confirm Password fields, and a drop-down box to select the user Role setpoint. Clicking on a user entry in the list opens the dialog box to edit information for that user. See Figure 16.
PAGE 19
Wi-Fi Administration Diagnostics The Diagnostics screen initiates the retrieval of the Diagnostic and Event Log files. See Figures 17 and 18. Figure 17. The Retrieve Full Diagnostics Logs button on the Diagnostics screen. Figure 18. The Retrieve Security Log button on the Diagnostics screen.
PAGE 20
Wi-Fi Administration Profile The Profile screen enables the present user logged in to the Wi-Fi/GPS Unit to change password credentials. See Figure 19. Figure 19. The Profile screen. A pa s sword ent r y requ i re s at lea st one lowerca se a nd one upperca se character. When entries are complete, click on the Apply button to save the new password. Logout Button Clicking on the Logout button in the left menu closes the Wi-Fi Administration program and returns to the LinkStart Main screen.
PAGE 21
Wi-Fi/GPS Unit Configuration NOTICE Proper grounding with a wrist strap connected to ground is required when touching any components within the communication module or contacts on the R3 Communication Module connector. For the IntelliRupter fault interrupter R3 communication module, with the Wi-Fi/GPS Unit comes configured to be a direct replacement for the Wi-Fi/GPS Unit in the R0 communication module. This is the default wiring for the R3 Communication Module.
PAGE 22
Wi-Fi/GPS Unit Connectors Ethernet 1 Ethernet 2 USB not used Wi-Fi antenna DB9 connector GPS antenna Figure 20. The Wi-Fi/GPS Unit connectors. Interface Pinouts The RS-232 Radio Maintenance Port of the Wi-Fi/GPS Unit is configured as data-terminal equipment. See Figure 21.
PAGE 23
Wi-Fi/GPS Unit Connectors The Wi-Fi/GPS Unit Ethernet ports use RJ-45 connectors with the pinout shown in Figure 22. They are auto-sensing for assignment of transmit and receive lines (no crossover cables required) and auto-negotiate for 10-Mbps or 100-Mbps data rates, as required by the connected device.
PAGE 24
Regulatory Information Regulatory Notices FCC Statement This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
PAGE 25
Regulatory Information Industry Canada Radiation Exposure Statement This radio transmitter with model: S&C Wi-Fi/GPS has been approved by Industry Canada to operate with the antenna types listed in Table 5 with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.