User's Manual

ManualsBrandsS and C Electric ManualsElectronicsTripSaver Service Center Configurable Controller2

S&C Form 974 (10-16)

S&C TripSaver

II Cutout-Mounted Recloser

Controller Module

and USB Dongle User Guide

Table of Contents

Section Page Section Page

Introduction

Qualified Persons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Read this Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Proper Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Retain this Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Hardware

Contents of TripSaver II Controller Module . . . . . . . . . . . 4

Software

Download Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Install Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Launch Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Connect to a TripSaver II Controller Module

and USB Dongle

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Summary of content (8 pages)

PAGE 1
S&C TripSaver® II Cutout-Mounted Recloser Controller Module and USB Dongle User Guide Table of Contents Section Page Introduction Qualified Persons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Read this Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Proper Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Retain this Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Regulatory Information . . . . . . . . . . . . . . . . . .
PAGE 2
Introduction Qualified Persons WARNING The equipment covered by this publication must be installed, operated, and maintained by qualified persons who are knowledgeable in the installation, operation, and maintenance of radios in electric power distribution equipment, along with the associated hazards.
PAGE 3
Introduction Regulatory Information This device complies with part 15 of the FCC rules and regulations regarding unlicensed transmissions. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference. This device complies with Industry Canada licence-exempt RSS standard(s).
PAGE 4
Hardware Contents of TripSaver II Controller Module Ac Adapter Power Outlet Plug Adapters USB Dongle Contoller Module This Manual 4 S&C Form 974
PAGE 5
Software Download Software IntelliLink® TripSaver II Controller Module Setup Software is available for download only to customers who have purchased the module. For each controller module purchased, the user is entitled to install and use S&C IntelliLink TripSaver II Controller Module Setup Software on no more than two computers at a time. The latest software release is posted on the S&C Automation Customer Support Portal at www.sandc.com/support/ automation-customer-support-portal.asp.
PAGE 6
Connect to a TripSaver II Controller Module To connect to a TripSaver II Controller Module to apply your new settings, follow these steps. Step 1 Install USB Transceiver A USB transceiver must be installed on your computer to communicate with a TripSaver II Controller Module. Insert the USB transceiver into any USB port on your computer. See Figure 1. The installation process should be automatic.
PAGE 7
Connect to a TripSaver II Controller Module (d) To verify that your TripSaver II Controller Module is powered up, place a magnet next to the controller module and observe the LCD screen. See Figure 5. If the LCD screen begins to scroll, it indicates the unit has been successfully powered up. Your setup, at the end of Step 2, should look like the picture in Figure 5.. Figure 5. Verify module is powered up.
PAGE 8
Connect to a TripSaver II Controller Module Step 3 Obtain Transceiver ID A Transceiver ID unique to each TripSaver II Controller Module is needed to establish communications between your computer and the device. See Figure 6. The ID consists of a 32-digit character string in the format of “0019C900.00020000. _ _ _ _ _ _ _ _ . _ _ _ _ _ _ _ _”. You must enter the ID in order to communicate with each TripSaver II Controller Module.