Intruder Detector using a radar principle URX-P01 User’s Manual Written By Device Development Group S-1 CORPORATION 168, S1 BUILDING, SOONHWA-DONG, JOONG-GU, SEOUL, KOREA Tel: +82 1588 3112 Fax: +82 2 2131 8869 Website: www.s1.co.kr Revised: May 2015 CAUTION!! • This equipment may only be operated Indoors. • Do not use to Outdoors. • Do not intentionally install aimed at windows or outside opening doors.
Table of Contents Introduction & Information ………………………...............……….1 Features of the UWB Sensor....……………………………………...2 Coverage of the UWB Sensor.……………………………………….3 UWB Sensor Specifications………………………………………….4 Installation………………………………………………………………5 Operational precautions……………………………………………...
INTRODUCTION & INFORMATION Introduction The UWB(Ultra Wide Band) sensors refers to a kind of radar technology that was traditionally used in military applications. When used as a security means, it’s low power, wide band characteristics often causes frequent false alarms. Overcoming such limitations with its excellence in technology, S1 showcases the first ever UWB-based security sensor in the world.
FEATURES OF THE UWB SENSOR Features of the UWB Sensor The diagram below shows several important features of the UWB Sensor: UWB Antenna GB-41 (Bracket) Lens LED [SET] Terminal (Power, COM,Tamper) Magnetic Switch Point Rotary Switch Label (System) [TOP] - 2- [BOTTOM] UWB Intrusion Detection Sensor – URX-P01
COVERAGE OF THE UWB SENSOR Coverage of the UWB Sensor Maximum detection area of the sensor is as follows: Horizontal View Vertical View 0m 0ft 1.8m 2.4m 6ft 3.0m 0m(0ft) 8ft 2m(6.5ft) 5m(16.4ft) 10ft 10m(32.8ft) Note - Installer is to walk into the pattern or may walk perpendicular to the pattern to verify the pattern.
UWB SENSOR SPECIFICATIONS UWB Sensor Specifications The specification of the sensor refer to the following table: Model URX-P01 Detection Method Impulse Radio(Ultra Wide Band) Colors URX-P01-WR : White Coverage Wide: 8m x 10m(26.24 x 32.80ft), 80˚ Wide Mounting Height 2.0 ~ 3.0m(6.5 ~ 10ft) Intruder Speed 0.3 ~ 1.5m/sec.(1 ~ 5ft/sec.) LED Alarm Indicator Red LED ON (When detecting) Tamper Parameters N.C (200VDC 0.1A max.) Alarm Output Period 2 Sec. Alarm Output N.C (60VDC 0.
INSTALLATION 1 Step : Using key separate “TOP” and “BOTTOM” 2 Step : Assemble “Bottom” and “GB-41” 3 Step : Connection “Top” and “Wire” SPARE TAMPER ALRAM 12VDC NC C SP NC C (-) (+) - 5- UWB Intrusion Detection Sensor – URX-P01
INSTALLATION 4 Step : Assemble “Top” and “Bottom” ※Adjustable detection range from 1 to 10 meter by rotary switch Switch Direction Range 0 1 10m 1m 2 2m 3 4 5 6 7 8 9 3m 4m 5m 6m 7m 8m 9m ☞ Note that each adjusted range has ±0.5m deviation Be sure walk test after installation Note 1. The unit is to be tested at a min once per year. 2. This unit is designed to detect a burglar or an intruder. When an alarm control panel is activated, the unit detects a burglar or an intruder.
OPERATIONAL PRECAUTIONS Operational precautions • Do not apply voltages higher than the rated voltage. • When swaying objects(mobiles of metal material), in the detection area, change the direction or adjust the detection distance. AC220V • Do not install where dogs and cats. • Do not install in the swaying wall. • Do not install the outdoor. • Do not install the curtain(blind) by the external wind swaying. • Do not install near any moving fan.