Smart FingerPrint Reader CDR-CDR-0193X / CFN-1000 User Manual (Ver2.
Safety precautions These precautions aim at preventing users from being injured, experiencing discomfort or having property damaged. Be sure to read them thoroughly. Warning If this notice is ignored, the user may be fatally injured. Caution If this notice is ignored, the user may be injured and/or damaged in properties Warning ●DO NOT randomly move or relocate the system.
Caution ●DO NOT allow children to mishandle the system. An accident may occur or a system failure. ●Be sure to frequently clean the system of dust. ●Be sure to protect your fingers from the sharp edges of the card. ●Be sure to keep the card with you. If lost, please notify us. ●DO NOT make scribblings on the card or allow it to be tainted or disfigured. ●DO NOT allow children access to the card or place it around any magnetized appliance such as a TV, refrigerator, etc.
Before system use: Familiarize yourself with the names of the system components. ▼ Smart Fingerprint reader LED Entrance/exit : turns green in power provision and gets blinking during user authentication. LCD Abnormal conditions : turns red in Display the current reader reader abnormalities. status. Set conditions : turns yellow in activated crime prevention function.
1. Input/Output Spec.
2.
Before system use: How to use buttons Enter button: enables you to select a menu or enter a number. If SBMS is connected, you can use this button for set/release. Esc button: enables you to delete/modify an entered number, to cancel a selection in menu mode, or to go back to a previous menu. To change to attendance mgmt/ attendance & exit (or access) mode, press and hold the button for over two seconds.
Menu Configuration Menu items in Setup mode Setup Menu 1.Card Reader 2.User Add/Del Card Reader User Add/Del 1.Master Add/Del 1.Registration 2.Setup Reader 2.Delete 3.Delete All Master Add/Del 1.Registration 2.Delete Setup Reader Access Operation Mode 1.Access 2.Set Time 2.Attendance Attendance 1.Operation Mode 2.Authentication Authentication 3.Beep&Voice 4.Security Level 1.Reader No - Authentication1.RF Card & FP 2.RF Card 1.Set Network 2.Attend.Time 3.Access Control 4.Open Duration 5.
How to use: I. Managing the card reader Going to Setup mode: In this case, one user should be registered as a master. 1. Press the ‘Enter’ and ‘F3’ buttons simultaneously. 2. When the LCD screen displays ‘-Master Authentication- Approach master card or input ID number:', place your card over the card reader. _ M aster _ Authentication Approach m aster card or input ID num ber ID : _______________ 3.
Registering (Adding) a master: Up to five masters can be registered. 1. In Setup mode, select “1. Card Reader.” 2. Select “1. Master Add/Del.” - Card Reader 1.Master Add/Del 2.Setup Reader 3. Select “1.Registration.” -Master Add/Del1. Registration 2. Delete 4. When the message, “- Master Registration - Approach card to be registered or Input ID:” is displayed, place a card for master access over the card reader.
Deleting a master 1. In Setup mode, select “1. Card Reader.” 2. Select “1.Master Add/Del.” - Card Reader 1.Master Add/Del 2.Setup Reader 3. Select “2. Delete.” -Master Add/Del1.Registration 2. Delete 4. When the message is displayed, “- Master Registration - Approach card to be registered or Input ID:.”, place the selected master card over the card reader.
Settingup authentication method : Either "RF Card+FP" or "RF Card" 1. Select '1.Card Reader'in setup mode. 2. Select '2.Setup Reader'. -Card Reader1.Master Add/Del 2.Setup Reader 3. Select '2.Authentication'. -Setup Reader1.Operation Mode 2.Authentication 3.Beep&Voice 4.Security Level 4. Select either '1.RF Card + FP' or '2.RF Card' - Authentication 1.RF Card + FP 2.RF Card "1.RF Card + FP" For a user authentication, put the card on the reader & follow the voice guidelines & then enter fingerprint.
Setting beep tones and voice settings: You can set the beep tones and voice to be activated/de-activated. 1. In Setup mode, “1Card Reader.” 2. Select “2. Setup Reader.” -Card Reader1.Master Add/Del 2.Setup Reader 3. Select '3.Beep & Voice'. -Setup Reader1.Operation Mode 2.Authentication 3.Beep&Voice 4.Security Level 4. Indicate Beep & voice setting up menu. Select “On” or “Off” - Beep&Voice : ON 1. ON 2.
Setup Security Level: Function for successful level settingup during the authentication Security LevelLow level: easy to authenticate but lots of other peoples’ authentication failure occur High level: small errors occur but low probability of authentication success 1. Select '1.Card Reader'on the setup menu 2. Select '2.Setup Reader' -Card Reader1.Master Add/Del 2.Setup Reader 3. Select'4.Security Level' -Setup Reader1.Operation Mode 2.Authentication 3.Beep&Voice 4.Security Level 4.
Setting Operation mode: The reader can adopt one of six operation modes depending on your company’s requirements. Complying with the operation mode specified in the contract, you need to set the mode in use. If you want to select another mode, be sure to contact our service center in advance. 1. In Setup mode, select “1. Card Reader.” 2. Select “1. Operation Mode.” -Setup Reader 1.Operation Mode 2.Authentication 3.Beep&Voice 4.Security Level 3.
1. When you select "1. Attendance/exit (access) & Crime Prevention" This operation mode only needs to be selected when you use S1’s crime prevention system (GBMS). Selecting “1. Attendance/exit & Crime Prevention,” you can see the sub-menu items as shown below: - Setup Reader 1.Reader No. 2.Setup Time Setting card reader No.: With S1’s crime prevention system in use, you need to set a different number for each system for normal communication. GBMS: 01~04, FS: 01~02 1. Select “1. Reader No.
2. When you select "2. Attendance" This operation mode is required when you select the Attendance function alone. Selecting “2. Attendance”, you can see the sub-menu items as shown below: - Setup Reader 1.Set Network 2.Attend.Time 3.Access Control 4.Open Duration 5.Forcing Open 6.Forcing Close 7.Set Time 8.Initialize Setting network: In Attendance program operation, you need to enter network settings as accurately as possible for normal use. 1. Select “1.Set Network” - Setup Reader 1.Set Network 2.
5. Enter a port number and press the Enter button. Port Number ____ 6. The LCD screen displays the message “Completed. - Reboot..!!”. The reader will then reboot. If you want to modify settings you entered, existing values will be displayed. For modification, you can delete a value with the Esc button for re-registration. Setting Attendance time: You can alternate between Automatic time shift and Manual time shift modes. 1. Select “2. Attend. Time” - Setup Reader 1.Set Network 2.Attend.Time 3.
5. The current Friday attendance time is displayed. Delete the current time and enter a new time, then press the Enter button. -Friday Attendance08:00 - 09:00 6. The current Saturday leaving time is displayed. Delete the current time and enter a new time, then press the Enter button. -Friday Leaving office11:00 - 14:00 7. The current Saturday attendance time is displayed. Delete the current time and enter a new time, then press the Enter button. -Weekend Attendance08:00 - 09:00 8.
Setting limited attendance/exit (access): This function enables limits to be set for user access. 1. Select “3. Access Control” - Setup Reader 1.Set Network 2.Attend.Time 3.Access Control 4.Open Duration 5.Forcing Open 6.Forcing Close 7.Set Time 8.Initialize 2. The current access setting status will be displayed. Select either “1.Global Access” or “2.Local Access.” -Access : Global1.Global Access 2.
Setting the door open time: In user authentication, the electric door lock remains open for a specified time. This function enables setting of the door open time. 1. Select “4. Open Duration” - Setup Reader 1.Set Network 2.Attend.Time 3.Access Control 4.Open Duration 5.Forcing Open 6.Forcing Close 7.Set Time 8.Initialize 2. Delete the current set time and enter a new time (up to 30 seconds). Then press the Enter button.
Setting door open by force: This setting enables the door open for a specified time. When the set time is expired, the electric lock system of the door will be back in operation. 1. Select “5. Forcing Open” - Setup Reader 1.Set Network 2.Attend.Time 3.Access Control 4.Open Duration 5.Forcing Open 6.Forcing Close 7.Set Time 8.Initialize 2. The current forced open status is displayed. Select “1. Setup.” -Status:RelaeseForcing Open 00:00 ~ 00:00 1.Setup 2.Release When you select “2.
Setting door closed by force: This setting enables the door to be locked for a specified time. During the time, a common user cannot use the authentication function. Only a master can use it. When the set time expires, the electric lock system of the door will be back in operation. 1. Select “6. Forcing Close” - Setup Reader 1.Set Network 2.Attend.Time 3.Access Control 4.Open Duration 5.Forcing Open 6.Forcing Close 7.Set Time 8.Initialize 2. The current forced close status is displayed. Select “1. Setup.
Setting a time 1. Select “7. Set time.” - Setup Reader 1.Set Network 2.Attend.Time 3.Access Control 4.Open Duration 5.Forcing Open 6.Forcing Close 7.Set Time 8.Initialize 2. Select either “1. Setup Manually” or “2. Download.” -Setup Time1.Setup Manually 2.Download In case of "1. Setup Manually" 3. The current date is displayed. With the Esc button, delete the existing year/month/date and enter a new one with the number buttons. Then, press the Enter button. Input Correct Date 2002. 11. 04 4.
Getting initialized: This function aims at initializing events (Attendance information) or reader setting information stored at the reader. 1. Select “8. Initialize.” - Setup Reader 1.Set Network 2.Attend.Time 3.Access Control 4.Open Duration 5.Forcing Open 6.Forcing Close 7.Set Time 8.Initialize 2. Select either “1.Event Init” or “2. Setup Init.” -Initialize1.Event Init 2.Setup Init 3.Reboot In case of "1. Event Init" 3. The LCD screen displays “Event Init.” To initialize an event, select “1.
How to use: II. Registering/deleting a user Registering (adding) a user: The user registration function is available in “Attendance” operation mode only. Up to 1,000 users can be registered. 1. In Setup mode, select “2. User Add/Del.” -Setup Menu1.Card Reader 2.User Add/Del 2. Select “1. Registration.” -User Add/Del- 1.Registration 2.Delete 3.Delete All 3. When the LCD screen displays “Approach card to be registered”, place a user access card over the card reader.
Deleting a user: This setting enables deletion of a registered user. This function allows for deletion of an individual user (Delete) or deletion of all users simultaneously (Delete All). 1. In Setup mode, select “2.User Add/Del.” -Setup Menu1.Card Reader 2.User Add/Del In case of “2. Delete” 1. Select “2. Delete.” -User Add/Del1. Registration 2.Delete 3.Delete All 2. The current number of registered users is displayed.
3. You will see a message, “Completed”, and then the screen reverts to the previous menu. Completed If all users are deleted, the screen displays “No registered card.” No registered card In case of entire deletion, the master will remain intact.
How to use: III. Managing the card reader Copying DB: This function enables the DB of a registered reader to be copied to a new reader. 1. Open the cover of the reader. 2. Connect the two readers with a communication cable. 3. Press the Enter and Leave buttons at the same time.
How to use: IV. For users In Access Operation mode Creating an access (Attendance/exit) A user can create an access with only a few easy steps. Place the card over the card reader. ●Without a card, you will not be able to create an access with crime prevention. Setting crime prevention mode (Connect to the S1’s alarm system) When you setup the crime prevention mode, the card will work seamlessly with S1 Corporation’s crime prevention system in crime prevention mode.
Button types 1. When the Function button is pressed, the LCD screen displays sub-menus, where you can select a mode and handle the card. ●When the "Enter?" and the "Leave?" button are pressed, the following sub-menus are displayed. - Enter M enu - - Leave M enu - 1. Personal 1. Personal 2. Public 2. Public ●The following sub-menus are displayed on the LCD screen. Personal Normal attendance Enter Enter? Public 1. Hospital 1. Sort Biz-Trip 2. Sickness 2. Biz-Trip 3. 1/2 Vacation 3.
This setting prevents the Attendance mode from being shifted automatically. Press the function button you want. Place your card over the card reader. ●Without any card, you cannot use the Attendance reader. ●The following shows the basic settings of Attendance time. ●As the last Attendance mode will remain in your card, you can check on the LCD screen if the current Attendance mode is what you want before handling the card.
Inquiring (monitoring) the working hours per employee Requesting working hours and overtime hours from the server to view on the reader. 1. Press the Enter button and the F4-Leave? button simultaneously. 2. Select “1. Operation Mode.” This function is available only in Attendance operation mode. - Monitor mode 1. Operation Mode 2. Authentication 3. Beep&Voice 3. As for “1. Operation Mode”, the following monitor mode will be displayed depending on the current operation mode. - Attendance 1. Attend.Time 2.
