Use and Care Manual

ManualsBrandsRYOBI ManualsOutdoor Power EquipmentReplacement Blades for 3-in-1 for Fixed String Trimmer Head (8-Pack)

WARNING:

To reduce the risk of injury, user must read and understand the op-

erator’s manual for their string trimmer before using this accessory.

Always wear eye protection with side shields marked to comply

with Z87.1 along with hearing protection. Ensure compatibility and

proper fit before using this accessory. Stop the string trimmer and

remove battery pack or disconnect spark plug wire before changing

or adjusting accessories.

WARNING:

Do not use this accessory if a part is damaged or missing. If you are

not comfortable performing any of the functions described in these

instructions, take your unit to an authorized service center. Use of

a trimmer head that has been improperly assembled could cause

the trimmer head to come apart and/or detach from your trimmer

and result in serious personal injury and/or property damage.

PACKING LIST

See Figures 1 - 2.

Trimmer Head Assembly, Spacer, Silver Bolt, Black Bolt, Silver Nut,

Black Nut, 0.095 in. Pre-cut Line, Locking Pin, Washer, and Operator’s

Manual

INSTALLING TRIMMER HEAD

See Figures 1 - 7.

The Fixed Line/Bladed Trimmer Head installs differently on different

string trimmer attachments. Assembly instructions will vary based

on the style and type of attachment you have. See figures 3 and 4

to determine if you have a curved shaft or straight shaft attachment

and if your attachment comes with or without an arbor. Refer to

the Installation Chart to determine the appropriate items for your

attachment. Be sure to follow the instructions for your attachment

style and type.

NOTE: If you cannot identify the style and type of attachment you

have, contact customer service for assistance.

Stop the engine or motor, disconnect the spark plug wire for gas

power heads, remove the battery pack for cordless power heads,

or disconnect the plug from the power source for electric power

heads.



Remove the trimmer head housing by rotating the lower housing

counterclockwise so the arrow on the upper housing aligns with

the post on the lower housing.

Separate the upper housing from lower housing and set aside.

Locate the bolt or nut, and/or spacer required to install the trimmer

head to your attachment. Refer to the Installation Chart for details.

INSTALLATION CHART

If the trimmer head does not fit with any of the adaptors or

hardware supplied, contact Customer Service at 1-800-860-4050

for assistance.

Style Type Items Needed for Installation

Curved

Shaft

With

Arbor

Spacer, Upper Housing, Lower

Housing,Washer, and Black Bolt

Curved

Shaft

Without

Arbor

Upper Housing, Silver Nut, and Lower Housing

Straight

Shaft

With

Arbor

Spacer, Upper Housing, Lower

Housing,Washer, and Silver Bolt

Straight

Shaft

Without

Arbor

Upper Housing, Black Nut, and Lower Housing

FIXED LINE/BLADED

TRIMMER HEAD

AC053N1FH

Fig. 3

Fig. 4

Fig. 1

Fig. 2

STRAIGHT

SHAFT

UPPER

HOUSING

LOWER

HOUSING

SILVER

BOLT

SILVER

NUT

LOCKING

BLACK

NUT

WASHER

BLACK

BOLT

CURVED

SHAFT

CURVED SHAFTS

STRAIGHT SHAFTS

ARBOR

SPACER

995000955

8-12-19 (REV:01)

Summary of content (6 pages)

PAGE 1
FIXED LINE/BLADED TRIMMER HEAD AC053N1FH WARNING: To reduce the risk of injury, user must read and understand the operator’s manual for their string trimmer before using this accessory. Always wear eye protection with side shields marked to comply with Z87.1 along with hearing protection. Ensure compatibility and proper fit before using this accessory. Stop the string trimmer and remove battery pack or disconnect spark plug wire before changing or adjusting accessories.
PAGE 2
For units with arbors:  Install the spacer onto the upper housing.  Slide the spacer and upper housing onto the arbor. NOTE: The arbor will perforate the label on the bottom of the lower housing. This will allow the arbor to insert through the unit. NOTICE: ARBOR ARBOR Make sure the arbor is fully seated into the hex-shaped pocket on the spacer before proceeding. An arbor that is not fully seated will cause damage to the upper housing and spacer.
PAGE 3
TÊTE POUR TAILLE-BORDURE À FIL FIXE/À LAME AC053N1FH AVERTISSEMENT : Pour réduire les risques de blessure, l’utilisateur doit lire et comprendre le manuel d’utilisation de son taille-bordures avant d’employer cet accessoire. Toujours porter une protection oculaire certifiée conforme à la norme ANSI Z87.1 ainsi qu’un protection auditive. S’assurer que l’accessoire est compatible et qu’il est bien installé avant de l’utiliser.
PAGE 4
Pour les unités équipées d’un axe :  Installez l’entretoise sur la section du boîtier supérieur.  Glissez l’entretoise et la section du boîtier supérieur sur l’axe. NOTE : L’axe perforera l’étiquette sur la partie inférieure du boîtier. Ceci permettra d’insérer l’axe à travers l’unité. ARBRE COURBÉE AVIS : AXE AXE S’assurer que l’axe est correctement inséré dans le logement hexagonal de l’entretoise avant de procéder.
PAGE 5
CABEZAL RECORTADORA DE LÍNEA FIJA/CON HOJAS AC053N1FH ARMAZÓN SUPERIOR ADVERTENCIA: Para reducir el riesgo de lesiones, el usuario debe leer y comprender el manual del operador de la recortadora de hilo antes de usar este accesorio. Siempre póngase protección ocular con la marca de cumplimiento de la norma ANSI Z87.1 junto con protección auditiva. Asegúrese de que sea compatible con el producto antes de utilizar este accesorio.
PAGE 6
Para las unidades con árboles:  Instale el separador en el armazón superior.  Deslice el separador y el armazón superior en el árbol. NOTA: El árbol perforará la etiqueta de la parte inferior de la carcasa inferior. Esto permite insertar el árbol en la unidad. AVISO: ÁRBOL ÁRBOL Asegúrese de que el árbol esté bien colocado en el compartimento hexagonal del separador antes de continuar. Si el árbol no está bien colocado, el armazón superior y el separador se dañarán.