OPERATOR’S MANUAL 18 VOLT POLE PRUNER P2500 BATTERIES AND CHARGERS SOLD SEPARATELY Your pole pruner has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product. Thank you for your purchase.
TABLE OF CONTENTS n Introduction ..................................................................................................................................................................... 2 �n General Safety Rules ....................................................................................................................................................... 3 �n Specific Safety Rules.............................................................................................................
GENERAL SAFETY RULES n Keep all parts of your body away from any moving part. n Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with the switch is dangerous and must be repaired. n Avoid accidental starting. Be sure switch is in the locked or off position before inserting battery pack. Carrying tools with your finger on the switch or inserting the battery pack into a tool with the switch on invites accidents. WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS.
SPECIFIC SAFETY RULES PRECAUTIONS AGAINST KICKBACK n Do not place battery tools or their batteries near fire or heat. This will reduce the risk of explosion and possibly injury. Kickback is a dangerous reaction that can lead to serious injury. n Keep a firm grip on the unit with both hands when operating the unit. Place your right hand on the rear handle and your left hand on the front handle. A firm grip will help you reduce kickback and maintain control of the unit. n Do not mutilate the battery pack.
SAFETY RULES FOR CHARGER n An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. a. That pins on plug of extension cord are the same number, size and shape as those of plug on charger.
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
FEATURES PRODUCT SPECIFICATIONS Net Weight............................................................... 7.37 lb. Charger Input ................................... 120 V, 60 Hz, AC only Charge Rate ..............................................................1 hour Motor .................................................................. 18 Volt DC Blade Length ................................................................ 5 in. Cutting Capacity...................................................
ASSEMBLY UNPACKING INSTALLING/REMOVING THE BLADE This product requires assembly. See Figures 2 - 3. INSTALLING THE BLADE: n Carefully remove the tool and any accessories from the box. Make sure that all items listed in the packing list are included. n Inspect the tool carefully to make sure no breakage or damage occurred during shipping. n Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool.
OPERATION NOTE: Batteries will not reach full charge the first time they are charged. Allow several cycles (operation followed by recharging) for them to become fully charged. WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. CHARGING A COOL BATTERY PACK If battery pack is within normal temperature range, the red LED on charger will come on.
OPERATION CHARGING A HOT BATTERY PACK P100 BATTERY PACK When using the tool continuously, the batteries in the battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack becomes discharged and is hot, this will cause the green LED to come on instead of the red LED. After 30 minutes, reinsert the battery pack in the charger.
OPERATION WARNING: Battery tools are always in operating condition. Therefore, switch should always be locked when not in use or carrying at your side. TO UNLOCK COLLAR U CO L L K See Figures 6 - 8. n Rotate the lower portion of the shaft adjustment collar to the “Unlock” position. N ADJUSTING THE SHAFT SHAFT ADJUSTMENT COLLAR n The lower shaft should now be free to slide down from inside the upper shaft. Make sure the shaft is pulled out to the desired position.
OPERATION STARTING AND STOPPING THE POLE PRUNER See Figures 9 - 10. STARTING THE POLE PRUNER n Hold the pole pruner as shown and ensure that you are well away from anything that may contact the blade. n Press and hold the trigger lock. n Depress the switch trigger. n Release the trigger lock. Continue to depress the trigger for extended operation. STOPPING THE POLE PRUNER 60° MAXIMUM n Release the trigger to stop the pole pruner.
OPERATION n Keep the unit at full speed the entire time you are cutting. n For second and final cuts (from top of limb or branch), hold the front cutting guide against the limb being cut. This will help steady the limb and make it easier to cut. n Allow the blade to cut for you; exert only light downward pressure. If you force the cut, damage to the blade or unit can result. n Release the trigger as soon as the cut is completed, allowing the unit to stop. CUTTING GUIDE Fig.
MAINTENANCE WARNING: WARNING: When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury. WARNING: Only the parts shown on the parts list are intended to be repaired or replaced by the customer.
OPERATOR’S MANUAL 18 VOLT POLE PRUNER P2500 • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-860-4050 for your nearest Authorized Service Center. You can also check our web site at www.ryobitools.com for a complete list of Authorized Service Centers. • MODEL NO. AND SERIAL NO.