What’s in the Box? System connects to four (4) cameras • 1 DIGITAL 7" TFT LCD Quad View Color Monitor with universal mount/stand and wire • 2 66' Extension Cables for Backup Cameras • 2 33' Extension Cables for Side Cameras • 1 Remote Control • 1 Power Connection Wire • 1 Screw Kit for installation
Table of Contents Introduction ...................................................................................................4 Safety Information ..................................................................................5-7 Before Beginning Installation...................................................................8 Installation Guide.........................................................................................9 Wiring Camera & Monitor............................................
Introduction Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear View Backup Camera System! With this manual you will be able to properly install and operate the unit. The Backup Camera System is intended to be installed as a supplement aid to your standard rear view mirror that already exists in your vehicle.
Safety Information Please read the entire manual and follow the instructions and warnings carefully. Failure to do so can cause serious damage and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to this product. Improper installation will void manufacturer’s warranty. USAGE • The Rear View Camera System is designed to help the driver safely detect people and/or objects helping to avoid damage or injury.
Safety Information INSTALLATION • Electric shock or product malfunction may occur if this product is installed incorrectly. • Use this product within the voltage range specified. Failure to do so can cause electronic shock or product malfunction. • Take special care when cleaning the monitor. • Make sure to firmly affix the product before use. • If smoke or a burning smell is detected, disconnect the system immediately.
Safety Information If you have questions about this product, contact: Customer Service: Rear View Safety 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 1.800.764.1028 IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
Before Beginning Installation Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot or moving parts and electrical noisy components. We recommend doing a benchmark test before installation to insure that all components are working properly. Step 1: Choose the monitor and camera locations.
Installation Guide Camera Installation 1. Attach camera bracket close to rear marker lights, centered on vehicle. 2. Camera: Drill a 20mm (0.8in) diameter hole into vehicle body near the camera and bracket. Insert camera cable into vehicle (be careful not to kink cable) and fit grommet into hole. Apply sealant around grommet to increase resistance to water penetration. Connect camera to the camera extension cable which runs inside the vehicle. 3. Feed as much cable as possible into vehicle & clamp securely.
Installation Guide Monitor 1. To Attach the Pedestal mount to the dashboard or to the headliner use self-tapping screws and/or the adhesive pad. 2. Attach monitor to mount, and adjust mounting angle to allow optimum driver viewing comfort. (see figure 1.1 on page 11) F Infrared technology built into camera IRs are activated automatically according to the lighting conditions.
Installing the Monitor Figure 1.1 Figure 1.2 Figure 1.3 Figure 1.
Installation Diagram 33ft 33ft 66ft 66ft Camera Camera Camera Extension Cable Extension Cable Extension Cable Extension Cable 2 3 1 4 5 FUSE Monitor cable Camera 1. Red (power+) 2. Yellow (Left) 3. Brown (Right) 4. Blue (Back) 5.
Monitor Operation DOWN ARROW CAMERA SELECTION MENU/ UP ARROW SELECTION BUTTON POWER ON / OFF V1/V2 ▼ ▼ MENU REV ROTATE IMAGE (Back/Exit when in Menu Mode) • To turn onthe monitor, press “POWER” button. • To get to the menu, press “MENU” and use arrows to choose your settings • To display options press “MENU” to select. • Toadjust brightness, press “MENU”. Use arrows to choose desired camera and press “MENU” to select. Once selected, use arrows to set the brightness. • Toadjustcontrastpress“MENU”.
Splitting & Splicing Installing sun shield: Put shade cover on the display. Installing back cover: Put the monitor with shade cover in the back cover (only for embedded monitor) Splitting back cover: Hold monitor with 2 hands and detach with fingers, as indicated by arrows. (only for embedded monitor) Splitting sun shield: Take the monitor with the left hand and detach with right hand as indicated by the white arrow. (see below) 1. Red (-12-24V) 2. Green (video back) 3. Blue (trigger back) 4.
Positioning Reverse With Confidence™ 15
Power Harness Red (power+) Yellow (Left) Brown (Right) FUSE Monitor cable Blue (Back) Black (Ground) DESCRIPTIONS Blue - Back Brown - Right Yellow - Left Red - Power 12V+ Black - Ground 12V- 16 Rear View Safety
Troubleshooting Monitor Displays Blue Screen & Displays No Signal • Do a hard reset, unplug all cables and power cables and leave them out for 1 minute and then re-connect them. • Check to ensure that the connection to the camera is tight. • Verify camera cable is plugged into port labeled Backup Camera • Verify that the blue positive trigger on power harness is put to power 12v+. If the problem still persists, verify that alternate ports work.
Monitor Dimensions 7” Rotation Imager Menu/ (Exit in Camera Up Selection Down Power Menu On/Off Button SelectionArrowArrow Mode) 5.
Monitor Specifications TFT LCD Digital Monitor Screen Size 7” Display Format 16:9 / 500:1 Dot Resolution Display Brightness 800H x 3 (RGB) x 480V 400cd/m2 Viewing Angle U:50° / D:60° / R:70° Video Source 1Vp-p, 75Ω Video Input Power Supply 4 channel DC 12V OR 24V (+/-10%) Power Consumption 5W Video System Auto NTSC/PAL Weight 400G Dot Pitch 0.192H x 0.1805V Operating Temperature Overall Dimensions Impact Rating Sync System Reverse With Confidence™ -30°C ~ +80° C 7”L x 5.
Warranty One Year Warranty Rear View Safety, Inc. warrants this product against material defects for a period of one year from date of purchase. We reserve the right to repair or replace any such defective unit at our sole discretion. Rear View Safety, Inc. is not responsible for a defect in the system as a result of misuse, improper installation, damage or mishandling of the electronic components. Rear View Safety, Inc. is not responsible for consequential damages of any kind.
Disclaimer Rear View Safety and/or its affiliates does not guarantee or promise that the user of our systems will not be in/part of an accident or otherwise not collide with an object and/or person. Our systems are not a substitute for careful and cautious driving or for the consistent adherence to all applicable traffic laws and motor vehicle safety regulations. The Rear View Safety products are not a substitute for rearview mirrors or for any other motor vehicle equipment mandated by law.
If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 BETTER CAMERAS. BETTER SERVICE. IT’S OUR GUARANTEE.