hospitality BLE remote control user guide Telus date: 2017-08-03 version: 2 please note: this document must not be shared with third parties without prior written consent from ruwido austria gmbh
revision history version creation date author comments V1 2017-05-26 Ralph Leblhuber initial version V2 2017-08-04 Ralph Leblhuber updated references product version type description firmware version 2503-539 BLE2IR dongle 0.2.1 comments sticker on back side: model 2503A FCC ID: XYN503A IC: 8748A-503A 2759-515 Telus hospitality 1.0.0 1.0.0 list of reference documents no.
scope the purpose of this document is to describe the BLE2IR dongle and BLE remote control setup copyright 2017 ruwido austria gmbh - this document is the intellectual property of ruwido austria gmbh and contains confidential information. reproduction, modification, communication to third parties and any other use is strictly prohibited without prior written accordance of ruwido.
table of content 1 user installation and programming guide ........................................... 6 1.1 dongle and RCU pairing .......................................................................... 6 1.2 programming your TV ............................................................................ 7 1.3 programming your amplifier .................................................................... 8 1.4 direct code programming TV and amplifier ............................................
list of figures fig. 1: hospitality BLE RCU ...................................................................................... 6 fig. 2: BLE2IR dongle ............................................................................................. 6 fig. 3: Optik TV STB ............................................................................................... 6 list of tables tab. 1: TV brand list - top brands ............................................................................ 7 tab.
1 user installation and programming guide 1.1 dongle and RCU pairing 1. press “play/pause” and “on demand” keys simultaneously for 3 seconds the LED will start flashing red continuously 2. plug in the ble2ir dongle (fig. 2: BLE2IR dongle) to an available USB port of your Optik TV Set Top Box (fig. 3: Optik TV STB) 3.
1.2 programming your TV before you start to program your remote control, make sure your TV and set top box are switched on. to speed up your programming process, the most used TV brands have a 4-digit code that will be used in the programming process. search for the 4-digit code of your TV brand. in case your TV brand is not listed please use code 0 0 2 9 to search for all brands. please note that the search can take up to 15 minutes in that case.
1.3 programming your amplifier before you start to program your remote control, make sure your TV is switched off and Amplifier is switched on. to speed up your programming process, the most used Amplifier brands have short numbers that will be used in the programming process. in case your amplifier brand is not listed please use code 0 0 7 9 to search for all brands. please note that the search can take up to 15 minutes in that case.
1.4 direct code programming TV and amplifier 1. press and hold options key for 3 seconds, until the LED flashes twice green 2. enter the 4-digit code from the code list the LED flashes twice green 3. press the tv power/vol+/vol-/mute key to verify the functionality of this code in case an invalid code has been entered the red LED will be on for 2 seconds. if no key code is being entered within 10 seconds the remote will time out and the programming procedure needs to be started again. 1.
1.7 - notes in case of low battery (<2.
2 technician installation guide 2.1 querying the stored 4-digit TV code 1. press options button for a minimum of 3 seconds, LED flashes twice green 2. enter the code 1 0 0 2 – LED flashes twice red 3. to query the currently saved code, press 1 for first digit, 2 for second digit, 3 for third digit and 4 for fourth digit 2.2 querying the stored 4-digit amplifier code 1. press options button for a minimum of 3 seconds, green LED flashes twice 2. enter the code 7 0 0 2 - LED flashes twice yellow 3.
remote use the STB/RSTEP protocol 2.5 switching between layers BLE2IR dongle 1. press options button for a minimum of 3 seconds, LED flashes twice green 2. enter the code 0 9 0 5 – LED flashes twice green BLE2IR dongle will use RCMM - DEFAULT 3. enter the code 0 9 0 4 – LED flashes twice green BLE2IR dongle will use RSTEP 2.6 querying the stored 2-digit DB version 1. press options button for a minimum of 3 seconds, LED flashes twice green 2. enter the code 9 0 0 1 LED flashes twice green 3.
3 declaration User Information FCC 15.2: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Part 15 Statement. FCC 15.19/RSS Gen Issue 3 Sect. 7.1.3 This device complies with Part 15 of the FCC Rules and with Industry Canada licenseexempt RSS standard(s).
ruwido austria gmbh Koestendorfer Str. 8 . 5202 Neumarkt . Austria . t +43 6216 4571-0 . office@ruwido.com . www.ruwido.