Technical Specifications

TECHNICAL DATA
PTX-02
PAINTER’S TOUCH
®
ULTRA COVER 2X ENAMEL BRUSH
1
Form: GDH-504
Rev.: 073119
DESCRIPTION AND USES
Rust-Oleum
®
Painter’s Touch
®
Ultra Cover 2X Enamels
provides long lasting protection and durability. This enamel
of offers excellent coverage, chip resistance and color
retention. For even longer, lasting protection, use a Painter’s
Touch
®
Primer first.
PRODUCTS
QUARTS
1/2 PINTS
DESCRIPTION
1922502
1922730
Gloss Navy Blue
1938502
1938730
Gloss Hunter Green
1945502
1945730
Gloss Sun Yellow
1964502
1964730
Gloss Colonial Red
1966502
1966730
Gloss Apple Red
1974502
1974730
Semi-Gloss Black
1976502
1976730
Flat Black
1977502
1977730
Gloss Kona Brown
1979502
1979730
Gloss Black
1986502
1986730
Gloss Dark Gray
1990502
1990730
Flat White
1992502
1992730
Gloss White
1993502
1993730
Semi-Gloss White
1994502
1994730
Gloss Almond
224428T
224423
Gloss Deep Blue
240286
----
Satin Claret Wine
240284
240290
Gloss Nutmeg
242018
242054
Gloss Espresso
240285
----
Gloss Heirloom White
242057
----
Gloss Clear
267330
267300
Satin Blossom White
267332
267249
Satin Canyon Black
267333
267312
Satin Colonial Red
267334
267314
Satin Hunt Club Green
267335
----
Satin Stone Gray
----
267268
Flat White Primer
----
267310
Satin Claret Wine
----
267313
Satin Heirloom White
*258203
----
Gloss Aged Copper
*254100
*240288
Metallic Silver
*254079
*240287
Metallic Gold
*254101
----
Gloss Oil Rubbed Bronze
*Oil-Modified Alkyds
PRODUCT APPLICATION
Apply only when air and surface temperatures are between
50-90ºF (10-32ºC) and humidity is below 65% to ensure
proper drying.
PRODUCT APPLICATION (cont.)
SURFACE PREPARATION
Remove all dirt, grease, oil, salt and chemical contaminants
by washing the surface with a commercial detergent, or other
suitable cleaning method. Rinse with fresh water and allow
to thoroughly dry. Remove loose paint and rust with a wire
brush or sandpaper. Previously coated surfaces must be
sound and in good condition. Smooth, hard, or glossy
finishes should be scarified by sanding to create a surface
profile. The Painter's Touch Ultra Cover 2X Enamels are
compatible with most coatings, but a test patch is suggested.
WARNING! If you scrape, sand or remove old paint from any
surface, you may release lead paint dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS
ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH approved respirator to control
lead exposure. Clean up carefully with a HEPA vacuum and
a wet mop. Before you start, find out how to protect yourself
and your family by contacting the National Lead Information
Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
PRIMING
Use of Painter’s Touch 2X Primer provides superior
adhesion and hiding and is especially recommended for
bare wood and metal. The following primers are
recommended:
1980502
Gray Primer
224430T
Flat White Primer
APPLICATION
Before using, stir thoroughly to ensure any settled pigment
is re-dispersed. Thinning is not required. In hot, dry
conditions, thin with up to 2 ounces of water per quart to
extend dry time. Avoid painting in direct sunlight or on hot
surfaces. Use a good quality synthetic brush. Avoid
excessive brushing as this will reduce film thickness and
protection. Use light even strokes to ensure smooth and
uniform flow.
DRY & RECOAT TIMES
Dry and recoat times are based on 70°F and 50% relative
humidity. Allow more time at cooler temperatures. Dries to
touch in 30 minutes, dry to handle in 1 hour, and fully dry in
2-4 hours. Primers may be top coated after 2-4 hours.
CLEAN-UP
Clean brush and other application tools immediately with
soap and water.