VM1 Video Matrix HD Component Video Distribution System Instruction Manual
SAFETY PRECAUTIONS Important Safety Instructions 7. Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
TABLE OF CONTENTS INTRODUCTION Product Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Control Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Rear-Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 INSTALLATION Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Source Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Upconverter Configuration . . . . . . . . . .
INTRODUCTION Product Overview The VM1 Video Matrix works with a multiroom audio system to distribute analog component video over a single CAT-5e cable to each zone. Capable of handling high-definition component video signals, it also provides conversion of composite and S-video signals in some configurations. Designed for use with Russound RNET® multiroom solutions, the VM1 provides seamless integration with the Russound CAA, CAM, and CAV systems.
INTRODUCTION Control Methods The Video Matrix is controlled by the system to which it is connected. It switches video sources to the zones by receiving source selection commands from the the host system. The VM1 provides a choice of ports for receiving control data from the host system: two RJ-45 jacks for linking to a Russound RNET multiroom system; a DB9 serial connector; and a USB connector.
INSTALLATION Location Upconverter Configuration Locate the VM1 Video Matrix with the host system controller and source equipment to facilitate source and control connections. Locate the VMR1 Receivers near the video displays in the zones, within 300 feet (90 m) of the VM1. Models with upconverters are factory set to convert composite video. Follow the procedure below to set the input switches to S-video or Component as needed before installing the VM1 (see diagram below).
INSTALLATION Rack Mounting To rack mount the VM1, attach the supplied rack ears to the chassis as shown. Leave one rack unit of space open above and below the VM1 to allow proper ventilation of the chassis. Do not mount the VM1 above a device that produces high amounts of heat, such as an amplifier. Rack ear 3. Connect Receiver cables to VM1. Crimp RJ-45 connectors on the system end of the CAT-5e cables, following the T568A standard as shown.
INSTALLATION Typical Application Diagrams RGB cable DVD player* VM1 Video Matrix Audio to controller Power supply CAT-5e cables RJ-45 patch cable RGB cable VGA-component video adapter* VGA IN VMR1 Receivers RGB cable Component video distribution amplifier* VGA serial cable Audio to controller RGB cables SMS3 Smart Media Server Video display* CAM6.6T Multiroom Controller RJ-45 patch cable CAM6.
INSTALLATION Connection for RS-232 control by a home automation system 9
REFERENCE Technical Specifications VM1 Video Matrix Component video connectors: Zone output connectors: System cable: Maximum cable length: Video resolution: Communication ports: 3 RCA per input (RGB) 8-pole modular RJ-45 CAT-5e 300 ft (90 m) Up to 1080p 2 RJ-45 RNET Link 1 DB9 RS-232 1 USB 1.1 Power requirement: 24 VDC 2.5 A (adapter included) Chassis dimensions: 17” W x 3.43” H x 13.15” D (43.0 x 8.7 x 3.34 cm) Weight: 11.65 lb (5.
REFERENCE Warranty The Russound VM1 Video Matrix is fully guaranteed against all defects in materials and workmanship for two (2) years from the date of purchase. During this period, Russound will replace any defective parts and correct any defect in workmanship without charge for either parts or labor. For this warranty to apply, the product must be installed and used according to its written instructions.
VM1 Video Matrix Component Video Distribution System Instruction Manual Models VM1 4 VM1 4UC VM1 8 VM1 8UC VM1 8UC2 Russound 5 Forbes Road, Newmarket NH 03857 USA Tel 603.659.5170 • Fax 603.659.5388 www.russound.com Technical Support: tech@russound.com 28-1235 05/03/07 Copyright © 2007 Russound. All rights reserved. All trademarks are the property of their respective owners. Specifications are subject to change without notice. Russound is not responsible for typographical errors or omissions.