User's Manual

ManualsBrandsRuoey Lung ManualsElectronicsRemote Control

Chapter 1 Directions for Product Usage

1. The method of communication between the remote control and receiver is in the form of a Radio

Frequency (RF)fm channel. The best transmission range is within 3 meters. Customers are able to control the

remote without facing the receiver. There is a LED signature light on the remote control. When the light is on,

the message is being sent out. To avoid operation mistakes during transmission, other buttons are not valid

when the LED signature light is on.

2. The control buttons on the face of the remote control is made with fluorescent materials. In the dark, it will

automatically glow for at least 30 minutes after the board receives sufficient light.

3. If there is more than the standard safe weight on the head and foot mechanism, the mini controller will

automatically stop all functions. In this type of situation, the customer should remove the source of excess

weight from the mechanism. After the customer removes the weight from the machine, the controller will

automatically start all functions after 30 seconds.

4. The vibrating massage will be controlled by the mini-controller. If customers use massage functions

continuously within a 15 minute period, it will automatically shut down. After five minutes, the vibrating

massage function will be able to on again. During the time between the vibrating process and the five-minute

automatic shutdown process, customers are still able to adjust the movement of the bed frame. When the

adjusting mechanism is in operation, it will temporarily shut down the vibrating massage functions. After 3

seconds, it will restart the vibrating massage.

5. Before using any remote control and receiver, customers need to read the RF frequency code instructions.

Due to safety concerns, the same remote control model can only control its receiver. When using a new remote

and receiver, the customer needs to read the RF frequency code instructions before usage.

Procedure for

※

Learning the Frequency Codes

1) Assemble all connect on the transformer and receiver.

2) Plug in the transformer and receiver (AC120V 60HZ.)

3) Put the batteries into the remote control (AAA ×2)

4) Use the head of a pencil and lightly press the learning button for 3 seconds.

5) When the red light of the receiver blink, press any button on the remote control.

6) After you follow step 5, the red light on the receiver will blink again.

7) The reading for the RF frequency code is completed.

6. Press any button on the remote control. When the LED signature light is on, a message is being sent out by

the remote. This remote control is designed to lower the energy consumption of the batteries. When the LED

signature light turns dark or turns off, it means the battery has been drained and will need to be replaced by a

new battery.

7. The input transformer voltage is AC120V 60HZ, the output voltage is DC24V 3A. When there is a

short-circuit, a fuse on the transformer will be blown in order to protect the electrical equipment

(Fuse:1A~1.5A.) When the above situation occurs, the customer should seek professional assistance to fix the

Summary of content (4 pages)

PAGE 1
Chapter 1 Directions for Product Usage 1. The method of communication between the remote control and receiver is in the form of a Radio Frequency (RF)fm channel. The best transmission range is within 3 meters. Customers are able to control the remote without facing the receiver. There is a LED signature light on the remote control. When the light is on, the message is being sent out. To avoid operation mistakes during transmission, other buttons are not valid when the LED signature light is on. 2.
PAGE 2
problem instead of replacing the fuse by himself or herself. 8. Notice :The changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’ s authority to operate the device.
PAGE 3
LED Signature Light Chapter 3 Illustration for Operation 1. Raises / Descends the head area of the bed Raises the head area of the bed up: press “A” button until it adjusts to the proper position. Then release “A” button. Descends the head area of the bed: press “B” button until it adjusts to proper position. Then release “B” button. 2. Raises / Descends the foot area of the bed Raises the foot area of the bed up: press “C” button until it adjusts to the proper position. Then release “C” button.
PAGE 4
Decelerates/ Closes foot vibrating feature: press “I” button until it increases to the desired strength. Then release “I” button. ※ Explanations for Items 3 and 4 When you use the regular vibration, there are 8-zones of massage. The strength of vibration in each zone can be adjusted to different levels. The head and foot areas can also be modified separately.