Getting Started 3. Push in the cover to seal the DC-IN compartment. Figure 42. Installing the DC-IN Cover The DC-IN cover must be inserted correctly to prevent internal damage to the device. Removing the Protective Film from the Display The front display of the PM-522 is protected during transport by a transparent film. This film should remain on the front display during assembly to avoid damage to the front display surface. Only remove the film once all of the assembly work has been completed.
Operation Chapter 3. Operation Before First Time Use 1. Flip up the external battery cover with an angle. Figure 95. Removing the External Battery Cover 2. Use a tool to switch the DIP switch to ON. Figure 96.
Operation 3. Install the external battery cover to the battery cover holder. Figure 97. Installing the External Battery Cover Powering Up and Down the Device Powering Up the Device Only power up the PM-522 after connecting all of the devices. 1. Press and hold the power switch for 2 seconds. Figure 98. Power Up the PM-522 Powering Down the Device 1. Press and hold the power switch for 5 seconds. Figure 99.
Connecting to Network PM-522 Supports two ways to connect to a network: LAN and Wireless LAN Wireless Calibrating the Touch Screen The touch screens of all PM-522 devices that come delivered with an operating system (Windows or Linux) are already calibrated. You may need to calibrate your screen if you tap on one area and it registers in a different area of the screen. Make sure you use the stylus to complete the alignment process. 1. Tap Start > All Programs > HIDeGalaxTouch Tool > HIDeGalaxTouch Tool.
Operation 3. Tap and hold until shows OK. Figure 102. Calibration Screen 4. Tap OK to complete calibrate. Figure 103. Complete Calibrate Using the CMOS Setup Utility Your ruggedized tablet has a CMOS setup utility which allows you to configure important system settings, including settings for the Boot and AP menus. This chapter explains how to use the CMOS Setup Utility. BIOS Setup Menu The CMOS Setup Utility allows you to configure your device’s basic settings.
Operation 37
Troubleshooting Chapter 4. Troubleshooting Use the troubleshooting tables in this section to fix problems with the Wi-Fi connection, 802.1x security, or general problems with operating the computer. If you send the computer in for service, it is your responsibility to save the computer data and configuration. RuggON is responsible only for ensuring that the hardware matches the original configuration when repairing or replacing the computer.
Troubleshooting Troubleshoot 802.1x Security Use the following table to troubleshoot problems with your 802.1x security that will prevent you from connecting to your network, such as an incorrect password. Q. A. „ The computer indicates it is not authenticated. Make sure that: The User Name and Password parameters on the computer must match the user name and password on authentication server. You may need to reenter the password on both the computer and authentication server.
Troubleshooting 4. 5. „ The IP and MAC addresses. „ The access point IP and MAC addresses. „ The DTIM and beacon period. „ The radio transmit power and signal strength information. Tap the Diags tab to run a ping test to the host. 1. In the text field, enter the IP address of the host. 2. Tap Start Ping. The graph shows the amount of time it takes for the host to return the ping. Tap the Global tab to view the global property values of the Wi-Fi connection.
Troubleshooting „ Make sure the computer application is expecting input from a bar code. You may need to type this information instead „ Check to see if the right scanner model is selected. To check the setting go to RuggON Settings and select Data Collection > Scanner Settings. „ Check to see if the scanner cable is damaged. Q. The scanner does not read the bar code labels quickly, or the scanning beam seems to be faint or obscured. A. The scanner window may be dirty.
Troubleshooting Troubleshoot Operating the Computer Use this section to troubleshoot problems that may prevent you from being able to operate the compute r. Q. A. Q. A. Q. A. You press the Power button and nothing happens. Make sure that power is connected to the computer. The computer appears to be locked up and you cannot enter data. Restart the compute r. For help, see “ Restart Your Computer” on page 63. You tap the screen and nothing happens. Align your screen.
Troubleshooting Find Your System Component Versions Use the following procedure to find your system component versions on your computer. „ From the RuggON Settings main menu, tap Device Settings > System Component Versions. The System Component Version screen appears. Find Your Operating System, BIOS and MCU Versions Use the following procedure to find your operating system, BIOS and MCU versions. „ Tap Start > Control Panel > PM-522 Properties.
Maintenance Chapter 5. Maintenance Cleaning the Device Danger to electric shock when cleaning or maintaining the PM-522. To avoid electric shock, turn the PM-522 off and disconnect it from the power supply before cleaning or maintaining it. Housing „ The housing of the PM-522 is best cleaned with a damp cloth. „ Use compressed air, a high-pressure cleaner or vacuum cleaner may damage the surface.
VMC:
