User's Guide

ManualsBrandsRuckus Wireless ManualsElectronicsAccess point

Table Of Contents

T350d Access Point

Quick Setup Guide

NOTE: The minimum sowar

e revision for the T350d is

ZoneDirector (ZD) 10.1 or later, or SmartZone (SZ) 6.0 or later.

This Quick Setup Guide provides step-by-step instrucons on ho

to eld-install the RUCKUS T350d access point (AP). For detailed

informaon on planning the installaon, performing a site survey,

and operang the T350d, refer to the RUCKUS Outdoor Access

Point User Guide, available at hps://support.ruckuswireless.com.

WARNING! Only trained and qualied per

sonnel should be

allowed to install, replace, or service this equipment.

WARNING! Inst

allaon of this equipment must comply with

local and naonal electrical codes.

CAUTION! Form a 80-mm to 130-mm (3-in. to 5-in.) drip loop

in an

y cable that is aached to the AP or the building. This will

prevent water from running along the cable and entering the

AP or the building where the cable terminates.

CAUTION! Be sure tha

t grounding is available and that it meets

local and naonal electrical codes. For addional lightning

protecon, use lightning rods and lightning arrestors.

CAUTION! Make sur

e that proper lightning surge protecon

precauons are taken according to local electrical code.

CAUTION! RUCKUS s

trongly recommends that you wear eye

protecon before mounng the T350d.

This Guide in Other Languages

• 请从以下网站获得该指南的简体中文版 hps://

support.ruck

uswireless.com.

• Vous trouverez la version française de ce guide à l'adresse

suivante hps://support.ruckuswireless.com.

• このガイドの日本語版は hps://support.ruckuswireless.com

でご覧ください。

• 이 가이드의 한국어 버전은 웹 사이트 (hps://

support.ruckuswireless.com) 에서 확인하시기 바랍니다.

• Veja a versão em português (Brasil) deste guia em hp

s://

support.ruckuswireless.com.

• Puede ver la versión en español (América Lana) de esta guía

en hps://support.ruckuswireless.com.

Before You Begin

Before deploying RUCKUS products, please check for the latest

soware and the release documentaon.

• Release Notes and other user documentaon are available at

hp://support.ruckuswireless.com/documents.

• Soware upgrades are available at hp://

support.ruckuswireless.com/soware.

• Soware license and limited warranty informaon are available

at hp://support.ruckuswireless.com/warranty.

• Before deploying your RUCKUS Access Point, verify that all

items listed in Package Contents are included in the package. If

any item is damaged or missing, nofy your authorized RUCKUS

sales representave. Also, make sure that you have the

required hardware and tools.

Required Hardware and Tools

• No. 2 Phillips screwdriver

• Small at-blade screwdriver

• Wide at-blade screwdriver

• Torque wrench or torque screwdriver with sockets

• Long-nose pliers

• Electrical wire stripping and terminal crimping pliers

• Pipe or pole, or a sturdy at surface

• Electric drill with drill bits and customer-supplied wall anchors,

at washers, and hex nuts for at-surface mount

Package Contents

A complete T350d eld installaon package includes all of the

following items:

• T350d Access Point

• M25 data cable gland

• Ground wire with lug

• Pole/Wall Mount Bracket Kit

• Two steel pipe clamps

• Service Level Agreement/Limited Warranty Statement

• Declaraon of Conformity

• Regulatory Statement

• RUCKUS AP Geng Started Guide

• AP Cloud Management insert

• This Quick Setup Guide

FIGURE 1 T350d Package Contents

1. T350d Access Point

2. M25 da

ta cable gland

3. Ground wire with lug

4. Pole/Wall Mount Bracket Kit

Mounng Instrucons

Connecng and Sealing the RJ-45 Cables

Connect and seal the RJ-45 cables using the M25 data cable

glands.

WARNING! Do not use any P

oE injector not tested and

approved by RUCKUS to power the T350d Access Point.

FIGURE 2 T350d LEDs and Ports

1. Feed the end of the cable through the sealing nut, rubber O-

ring, clamping ring assembly, and cable gland base, as shown

in Figure 3.

NOTE: Do not seat the clamping ring and rubber O-ring

into the gland body unl the gland body has been torqued

to specicaons.

Published April 2021, Part Number 800-72737-001 Rev A

Summary of content (10 pages)

PAGE 1
• Veja a versão em português (Brasil) deste guia em https:// support.ruckuswireless.com. FIGURE 1 T350d Package Contents • Puede ver la versión en español (América Latina) de esta guía en https://support.ruckuswireless.com. T350d Access Point Quick Setup Guide NOTE: The minimum software revision for the T350d is ZoneDirector (ZD) 10.1 or later, or SmartZone (SZ) 6.0 or later. This Quick Setup Guide provides step-by-step instructions on how to field-install the RUCKUS T350d access point (AP).
PAGE 2
FIGURE 3 RJ-45 Cable and Gland Assembly FIGURE 4 Removing the Mounting Bracket Attaching the Mounting Bracket to a Pole 1. The AP mounting bracket attaches to the AP using a captive screw. Loosen the screw and pull up on the end of the bracket to remove the bracket from the AP, as shown in Figure 4. 2. Insert the open end of one steel clamp into two of the slots on the mounting bracket.
PAGE 3
FIGURE 7 Attaching the Mounting Bracket to the AP Powering the AP with DC Power FIGURE 9 Connecting a Good Earth Ground to the AP The AP can accommodate two sources of power: PoE (48V) power and 12V DC. The AP can draw power from the Ethernet input as a Class 4 device, providing a maximum of 18 W to the system. Alternately, power can be supplied through a customer-provided 12V DC power supply (12V DC preferred, 7-20V DC acceptable) that will connect to a two-pin terminal block.
PAGE 4
FIGURE 10 Installing a USB Dongle registered trademarks of Wi-Fi Alliance. All other trademarks are the property of their respective owners. Troubleshooting CAUTION! If required, you can reset the AP to its factory default settings by pressing the reset button located inside the PoE IN port. Use the tip of a pen or a 3-mm flat-blade screwdriver to press the reset button. Press and hold the reset button for 4 seconds or longer to restore to factory defaults.
PAGE 5
Business Unit - Ruckus Wireless Inc. 350 West Java Dr. Sunnyvale CA 94089 USA T: +1 650 265 4200 F: +1 408 738 2065 www.commscope.com Declaration of Conformity This declaration of conformity is issued under the sole responsibility of the manufacturer: Ruckus Wireless, Inc.
PAGE 6
T350d, T350c – Outdoor Enterprise AP Federal Communications Commission Notices Ruckus Wireless Inc., a CommScope Company This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 7
a. Any installation of either a master or a client device within 35 km of a TDWR location shall be separated by at least 30 MHz center-to-center) from the TDWR operating frequency. b. A voluntary WISPA sponsored database has been developed that allows operators and installers to register the location information of the UNII devices operating outdoors in the 5470 – 5725 MHz band within 35 km of any TDWR location (see http://www.spectrumbridge.com/udia/home.aspx ).
PAGE 8
Telecommunications Act. The low power radio-frequency devices must not be susceptible with the interference from legal communications or ISM radio wave radiated devices.
PAGE 9
Hereby, Ruckus Wireless Inc., declares that the radio equipment type is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://docs.commscope.com/?docs-box Български [Bulgarian] С настоящото Ruckus Wireless декларира, че описаното по-горе радиосъоръжение е в съответствие с Директива 2014/53/ЕС.
PAGE 10
T350d & T350c, Access Point Installation Addendum When the frequency band 5150 – 5250 MHz is used outdoors in the U.S.A, the FCC mandates that the energy radiated above 30° from the horizon remains below 21 dBm EIRP. This can be maintained during installation using the following guidance. When the device is installed level to the horizon, (i.e.