User's Manual

ManualsBrandsRuckus Wireless ManualsElectronicsR600 Access Point

Table Of Contents

Published September 2014, Part Number 800-70633-001 Rev B

R600 Access Point

Quick Setup Guide

This Quick Setup Guide provides step-by-step instructions

on how to set up your Ruckus Wireless R600 Dual Band

802.11ac Multimedia Wi-Fi Access Point. After completing

the steps described in this Guide, you will be able to place

the Access Point (AP) at your site and provide wireless

network access to users.

THIS GUIDE IN OTHER LANGUAGES

• 请从以下网站获得该指南的简体中文版

https://support.ruckuswireless.com.

• Vous trouverez la version française de ce guide à l'adresse

suivante https://support.ruckuswireless.com

• このガイドの日本語版は https://

support.ruckuswireless.com

でご覧ください。

• 이 가이드의 한국어 버전은 웹 사이트

(https://support.ruckuswireless.com

) 에서 확인하시기 바

랍니다 .

• Veja a versão em português (Brasil) deste guia em

https://support.ruckuswireless.com.

• Puede ver la versión en español (América Latina) de esta

guía en https://support.ruckuswireless.com.

BEFORE YOU BEGIN

Before deploying Ruckus Wireless products, please check for

the latest software and the release documentation.

• User Guides and Release Notes are available at

http://support.ruckuswireless.com/documents.

• Software Upgrades are available at

http://support.ruckuswireless.com/software.

• Open Source information is available at

http://opensource.ruckuswireless.com.

• Software License and Limited Warranty are available at

http://support.ruckuswireless.com/warranty.

PACKAGE CONTENTS

• R600 Access Point

• One wall-mount anchor kit, including two 1" No. 8 steel pan-

head Phillips sheet metal screws, one 5mm M2.5 x 1.06 Torx

security screw, and wall-mount anchors

• One external T-bar bracket (two unassembled parts)

• One unit removal pin

• Regulatory flyer

• Product warranty statement

• Declaration of Conformity, if required

•This Quick Setup Guide

STEP 1: COLLECT TOOLS AND SETUP REQUIRE-

MENTS

• A computer running Windows 7 (procedures for other OS’s

are similar)

• Two Cat 5e Ethernet cables

• No. 2 Phillips screwdriver and T8 Torx driver for wall mount-

ing anchor kit

• An AC power adapter (sold separately), or

an 802.3af- or 802.3at-compliant Power over Ethernet

(PoE) switch or PoE injector

• When mounting the R600 to a truss or pole, two customer-

supplied cable ties

STEP 2: CONNECT THE AP TO YOUR COMPUTER

Figure 1: Top view

1 After removing your Ruckus Wireless AP from its pack-

age, place it next to your computer.

2 Using an Ethernet cable, connect your computer’s net-

work port to one of the two ports on the AP.

3 Using an AC adapter (sold separately), connect the AP

12VDC port to a protected power source.

Alternatively, connect the PoE port to a PoE injector or

switch for both power and network connections.

4 Verify that the Power LED on the external enclosure is a

steady green.

Figure 2: Bottom view

STEP 3: PREPARE YOUR COMPUTER FOR AP

ETUP

1 On your Windows 7 computer, configure your network

adapter from the Local Area Connection settings as fol-

lows:

• Start > Control Panel > Network and Sharing

Center > Change Adapter Settings

2 Edit the TCP/IPv4 address settings as follows:

• Local Area Connection > Properties > Internet

Protocol Version 4 (TCP/IPv4) > Properties

The TCP/IPv4 Properties dialog box appears.

3 Select Use the following IP address (if it is not already

selected) and then make the following entries:

• IP address: 192.168.0.22 (or any address in the

192.168.0.x network)

• Subnet mask: 255.255.255.0

• Default gateway: 192.168.0.1

Leave the DNS server fields empty.

4 Click OK to save your changes.

Your changes are put into effect immediately.

Note: The R600 requires a minimum of ZoneFlex (ZF)

firmware version 9.8.1 or later, or SmartCell Gateway

(SCG) firmware version 2.5.1 or later, or virtual SmartCell

Gateway (vSCG) 3.0 or later.

IMPORTANT! If the AP is deployed with a ZoneDirector, then

refer to the ZoneDirector Quick Setup Guide and connect the

AP to your local network.

Note: The following procedures assume Windows 7 as the

operating system. Procedures for other OS’s are similar.

Important! Write down all of the currently active settings so

you can restore your computer to its current configuration

later (when this process is complete).

PoE Port 12VDC Port

Summary of content (4 pages)

PAGE 1
• Software License and Limited Warranty are available at http://support.ruckuswireless.com/warranty. 3 PACKAGE CONTENTS R600 Access Point Quick Setup Guide This Quick Setup Guide provides step-by-step instructions on how to set up your Ruckus Wireless R600 Dual Band 802.11ac Multimedia Wi-Fi Access Point. After completing the steps described in this Guide, you will be able to place the Access Point (AP) at your site and provide wireless network access to users.
PAGE 2
STEP 4: LOG INTO THE AP As specified earlier, the AP should be directly connected to your computer (through one of the Ethernet ports) and powered on, ready for setup. 1 On your computer, open a Web browser window. 2 In the browser, type this URL to connect to the AP: https://192.168.0.1 3 4 5 Press to initiate the connection. When a security alert dialog box appears, click OK/Yes to proceed.
PAGE 3
Mounting on a Recessed Drop-Ceiling T-Bar Note: This mounting bracket can also be used on a flush drop-ceiling T-bar, so the four rubber feet on the bottom of the AP minimize ceiling tile displacement. 7 Hold the R600 in place and gently push the locking tab (B in Figure 5) until its clasp grips the other edge of the Tbar.