Step-by-step Instructions

ManualsBrandsRuckus Wireless ManualsElectronicsAccess Point

H550 Access Point

Quick Setup Guide

This Quick Setup Guide provides step-by-step instrucons on how to set up

your RUCKUS H550 Dual Band 802.11ax Mulmedia Wi-Fi Access Point

Wall Switch. Aer compleng the steps described in this guide, you will be

able to access the H550 Access Point Wall Switch and begin providing

wired and wireless network access to users. The rest of this document

refers to the H550 Access Point Wall Switch as the H550.

The H550 has many opons:

• It can be mounted on a standard USA- or EU-style single-gang wall

outlet box.

• It can be powered by a customer-supplied IEEE 802.3af- or 802.3at, or

IEEE 802.3bt-compliant PoE switch or injector, or can be powered by an

oponal customer-ordered DC power adapter.

• It has side slots for one or two bypass cables. The mounng bracket has

locang hooks to keep the bypass cables aligned with the slots when

aaching the H550 to the mounng base.

• It can have a 3W customer-supplied USB device plugged in. The USB

device is very dicult to remove aer the H550 is aached to the

mounng base.

NOTE: The H550 requires RUCKUS base image 104.0 rmware or later.

Managed H550 deployments require SmartZone 6.0 or later, or

ZoneDirector 10.5 or later.

About Peripheral Devices

The H550 can supply power to USB devices and PoE-powered devices, and

the power supplied depends on the PoE power supplied to the H550.

• The USB port can supply power up to a maximum of 3W. The port is

intended for customer-specic USB peripherals.

• The LAN4 + PoE Out port is intended for PoE-powered peripheral

devices such as IP telephones.

TABLE 1 H550 Power Opons and Available Power for PoE Out and USB

H550 Power Source Power available for PoE Out and

USB

802.3af PoE PoE out disabled, USB disabled

802.3at PoE 12.95 PoE Out (802.3af Class 3),

USB disabled

802.3bt Class 5 PoE or DC power

adapter

12.95 PoE Out (802.3af Class 3)

3W USB

This Guide in Other Languages

• 请从以下网站获得该指南的简体中文版 hps://

support.ruckuswireless.com.

• Vous trouverez la version française de ce guide à l'adresse suivante

hps://support.ruckuswireless.com.

• このガイドの日本語版は hps://support.ruckuswireless.com でご覧

ください。

• 이 가이드의 한국어 버전은 웹 사이트 (hps://

support.ruckuswireless.com) 에서 확인하시기 바랍니다.

• Veja a versão em português (Brasil) deste guia em hps://

support.ruckuswireless.com.

• Puede ver la versión en español (América Lana) de esta guía en

hps://support.ruckuswireless.com.

Before You Begin

Before deploying Ruckus products, please check for the latest soware and

the release documentaon.

• Release Notes and other user documentaon are available at hp://

support.ruckuswireless.com/documents.

• Soware upgrades are available at hp://support.ruckuswireless.com/

soware.

• Open source informaon is available at hp://

opensource.ruckuswireless.com/open_source.

Package Contents

• H550 Access Point Wall Switch

• Mounng bracket

• Two 6-mm M3x0.5 Torx at head machine screws

• Two 1-inch 6-32 Phillips pan head machine screws

• Product warranty statement

• Regulatory yer

• Declaraon of Conformity, if required

• This Quick Setup Guide

Step 1: Collecng Tools and Setup Requirements

• No. 2 Phillips screwdriver and T10 Torx driver for the mounng bracket

screws

• A standard USA- or EU-style single-gang wall outlet box

• One of the following:

– Customer-supplied IEEE 802.3af/at/bt-compliant PoE switch and

customer-supplied Ethernet cable

– Customer-supplied IEEE 802.3af/at-compliant PoE injector and

customer-supplied Ethernet cable

– Customer-ordered DC power adapter (RUCKUS part number

902-2170-XX00, sold separately)

• An Ethernet cable with or without PoE run through the wall from your

LAN through the wall outlet box

• A PC with an Ethernet port and a wireless card with customer-supplied

Cat 5e or beer Ethernet cable

• (Oponal) One or two separate bypass cables run through the outlet

box

Step 2: Connecng the PC to the H550

1. Using an Ethernet cable, connect your PC's network port to the PoE In

port on the rear of the H550.

FIGURE 1 H550 Front view

2. Using an AC adapter (sold separately), connect the H550 48V DC port

to a protected power source.

3. Verify that the PWR LED on the rear of the enclosure is green. LED

may be solid or blinking.

Published November 2020, Part Number 800-72461-001 Rev B

Summary of content (3 pages)

PAGE 1
This Guide in Other Languages H550 Access Point Quick Setup Guide This Quick Setup Guide provides step-by-step instructions on how to set up your RUCKUS H550 Dual Band 802.11ax Multimedia Wi-Fi Access Point Wall Switch. After completing the steps described in this guide, you will be able to access the H550 Access Point Wall Switch and begin providing wired and wireless network access to users. The rest of this document refers to the H550 Access Point Wall Switch as the H550.
PAGE 2
Your changes are put into effect immediately. FIGURE 2 H550 Rear and bottom view Step 4: Logging In to the H550 Access Point As specified in Step 3: Preparing Your PC for H550 on page 2, the H550 should be directly connected to your PC (through the PoE In port on the back of the H550) and powered on, ready for setup. 1. On web browser window. 2. Enter https://192.168.0.1 to connect to the H550. 3. Press Enter to initiate the connection.
PAGE 3
without obstructing the H550 and preventing the H550 from mounting flush with the wall bracket. 4. When you have extra bypass cables (usually one or two) that are to bypass the H550, pull them through the wall outlet box. NOTE: The bypass cables can be Ethernet, coaxial, or any other type of cable, as required. Drape the bypass cables across one or both of the upper hooks on either side or both sides of the mounting bracket. Step 7: Attaching the H550 to the Mounting Bracket 1.