Installation Instructions

ManualsBrandsRSI VIDEOTECHNOLOGIES ManualsElectronicsIndoor Keypad

Product Summary

The Indoor Keypad Model XMB611 is designed for use in

conﬁguring/programming and operating a Videoﬁed

security

system. The keypad includes the following features:

Lithium batteries for long life.

2-line, 16-character alphanumeric LCD display

Built-in badge reader for arming/disarming

Built-in piezo for status and alarm sounds

Dual tamper function provides detection of both

wall and cover tamper.

Transmits check-in/status signal every 8 minutes.

Installation Guidelines

For easier installation, programming and RF testing

should be completed before mounting the control panel and

devices.

Install the keypad and other system devices in the following

order:

Programming/RF Testing - Program keypad and all other

devices into the control panel and test RF communication

from each intended device location to the control panel.

Mounting - Mount keypad and devices at the tested location.

Programming/RF Testing*

Open the casing by turning the button toward the opened

padlock symbol and press down lightly on the button to

separate the cover.

Insert 3 (minimum) or 4 (for longer life) SAFT 3.6v Lithium

AA LS14500 batteries.

New Installation: Put the control panel into

keypad registration mode by pressing the

programming button of the control panel one time.

Adding to existing system: Using a programmed

alphanumeric keypad, proceed through menus until the

display shows ADD A NEW DEVICE. Press Yes. The

display shows PRESS PROGRAM BUTTON OF DEVICE.

Adding to existing system without a keypad: Refer to

the installation manual of the control panel.

Press and release the programming buttons (CLR and

ESC/NO) on the XMB keypad. The keypad LED will ﬂash.

Wait for keypad display to show KEYPAD# RECORDED.

Press Yes. The display shows LANGUAGE: ENGLISH. Press

Yes. (This prompt will only appear when performing a

new installation).

Display shows RADIO RANGE TEST? Press YES, the

keypad starts displaying the number of successful pings

to and from the control panel out of 9 (0/9 to 9/9).

Devices must be installed in a location with a stable 9/9 RF

test result to ensure reliable communication.

Press YES to end radio range test, then press Esc/No.

Note: If this is a new installation (3A), the keypad display

prompts other system conﬁguration data. If adding a keypad to

an existing (operational) system, proceed to step 8.

When ﬁnished, exit from conﬁguration mode.

Note: The control panel automatically assigns alphanumeric

keypads automatically to Area 1 (Entry/Exit delay)

*For complete details, refer to the control panel installation manual.

www.videofied.com

INSTALLATION DATA SHEET

Keypad XMB611

Made by RSI VIDEO TECHNOLOGIES 1010-XMBIN February 2012

Summary of content (5 pages)

PAGE 1
Keypad XMB611 I N S TA L L ATI O N DATA S H E E T Made by RSI VIDEO TECHNOLOGIES 1010-XMBIN February 2012 Product Summary Installation Guidelines The Indoor Keypad Model XMB611 is designed for use in configuring/programming and operating a VideofiedTM security system. The keypad includes the following features: For easier installation, programming and RF testing should be completed before mounting the control panel and devices. > Lithium batteries for long life.
PAGE 2
Keypad XMB611 I N S TA L L ATI O N DATA S H E E T 1. Mounting 1 > Use proper tools and hardware. > Mount indoor in a temperature-controlled environment. > Mount keypad at height that provides proper viewing and convenience for the customer. > Mount in a location that provides customer convenience but out of view from windows. Separate base from Keypad. Mounting Holes 2 Hold base against mounting surface and mark the three mounting holes. Use the left or right side to level the keypad.
PAGE 3
Keypad XMB611 I N S TA L L ATI O N DATA S H E E T 4. Removal of Protective Film 3. Product Overview They keypad is protected by a transparent film. It is important to remove this film before using the keypad. LCD display with automatic backlight Red / Green LED Menu Navigation Arming Keys Assistance Requests RFID Badge reading zone 5. RFID Tag Reading The XMB keypad is equipped with a badge reader ISO/IEC 14443A. The optimal reading area is located around the 0 key. Compatible with MiFare 13.
PAGE 4
Keypad XMB611 I N S TA L L ATI O N DATA S H E E T FCC Regulatory Information for USA and CANADA FCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI VideoTechnologies may void the FCC authorization to operate this equipment. FCC Part 15.105 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 5
Keypad XMB611 I N S TA L L ATI O N DATA S H E E T 8. Specifications Electrical Data Physical Data Panel Compatibility Videofied Alarm Panel XL,XT,XTIP, V6000 ABS UL94-V0 Dimensions Power requirements: Type: Material (LxWxD):6.3 x 3.6 x 1.2 Inches (160 x 92 x 31 mm) 3.6v SAFT Lithium, LS14500, AA Batteries Only Nominal Voltage: 3.6v Low Voltage Limit: 2.1v - LCD will stop functioning but communication is working 3.