Installation Instructions

ManualsBrandsRSI VIDEOTECHNOLOGIES ManualsElectronicsKeypad

Product Summary

The Keypad CMA601 is designed for use in conﬁguration/

programming and operating with a RSI Video Technologies

security system. The keypad includes the following features:

Lithium batteries for long life.

2-line, 16-character alphanumeric LCD display

with backlighting.

Armed status red LED.

Built-in piezo for status and alarm sounds.

Dual tamper function provides detection for both wall

and cover tamper.

Transmits check-in/status signal every 8 minutes.

Installation Guidelines

For easier installation, programming and RF testing

should be done to check for good communication between

the control panel and all system devices before mounting

system devices. Install the keypad and other devices in the

order of the following steps:

Programming/RF Testing - program keypad and

all other devices into the control panel and test

RF communication from each intended device

location to the control panel.

Mounting - mount keypad at the tested location.

Programming/RF Testing

The following provides summarized steps for device

programming and testing. For complete details, refer to the

control panel installation manual.

Remove bottom screw,

separate base from keypad

and install batteries.

Re-attach base to

secure tamper switch.

Put control panel

into programming/

conﬁguration mode.

On keypad, press and

hold Clr and Esc/No

buttons together for

one second, then release

them. Wait for keypad

display to show KEYPAD

1 RECORDED.

Press Yes. The display

shows RADIO RANGE

TEST? Press Yes again.

The detector LED starts

ﬂashing and keypad display

shows RF TEST #/9

Press Yes to end radio range test, then press Esc/No.

Note: If this is the ﬁrst keypad programmed in a new installation,

the keypad display prompts you to enter other system conﬁguration data.

If you are adding the keypad to an existing (operational) system, proceed

to step 9.

Repeat steps 1 - 8 for all alphanumeric keypads.

When ﬁnished, exit conﬁguration mode.

Note: The control panel assigns alphanumeric keypads automatically

to Zone 1 (Entry/Exit Delay).

Refer to the users manual of your alarm panel to know how

use this device.

www.videofied.com

Screw

CLR and ESC/NO Buttons

LED

PRODUCT INSTALLATION SHEET

Keypad CMA601

Made by RSI VIDEO TECHNOLOGIES 2222-CMAIS March 2012

Summary of content (3 pages)

PAGE 1
Keypad CMA601 P R O D U C T I N S TA L L ATI O N S H E E T Made by RSI VIDEO TECHNOLOGIES 2222-CMAIS March 2012 Product Summary Installation Guidelines The Keypad CMA601 is designed for use in configuration/ programming and operating with a RSI Video Technologies security system. The keypad includes the following features: For easier installation, programming and RF testing should be done to check for good communication between the control panel and all system devices before mounting system devices.
PAGE 2
Keypad CMA601 P R O D U C T I N S TA L L ATI O N S H E E T Mounting 3 Drill pilot holes and install > Use proper tools and hardware. > Mount indoors in a temperature-controlled environment. > Mount in a location that provides customer convenience, but out of view from windows. 1 anchors where needed. Separate base from keypad. 2 Hold base against mounting surface and mark the three mounting holes.
PAGE 3
Keypad CMA601 P R O D U C T I N S TA L L ATI O N S H E E T FCC Regulatory Information for USA and CANADA FCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI VideoTechnologies may void the FCC authorization to operate this equipment. FCC Part 15.105 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.