Installation Instructions

ManualsBrandsRSI VIDEOTECHNOLOGIES ManualsElectronicsOutdoor Badge Reader

Product Summary

The Outdoor Badge Reader BR651 is designed for use in

operating a Videoﬁed security system. The Outdoor Badge

Reader includes the following features:

> Totally wireless, battery operated

> Dual tamper function provides detection for both wall and

cover tamper.

> Transmits check-in/status signal every 8 minutes.

> Mobility-Use outdoors or indoors with a fully weather

proof casing withstanding temperatures from -25°C to

+60°C.

> Depending the alarm panel used, up to 18 badges can be

recorded.

PROGRAM Button

Surface of the

badge reader

Indicator LED

Installation Guidelines

For easier installation and programming, RF testing should be

done to check for good communication between the control

panel and all system devices before mounting system devices.

Install the badge reader and other system devices in order of

the following steps:

Programming/RF Testing - program reader and all other

devices into the control panel and test RF communication

from each intended device location to the control panel.

Mounting - mount reader at the tested location.

Programming /RF Testing

The following provides summarized steps for device

programming and testing. For complete details, refer to the

control panel installation manual.

Remove top and bottom screw, separate base from Badge

Reader and install batteries.

Put control panel into conﬁguration/add a new device

mode using the keypad.

Press the programming button on the inside of the case.

Wait for keypad display to show Badge Reader Recorded

Re-attach base to secure tamper switch.

Press Yes on the keypad. The display shows RADIO RANGE

TEST? Press Yes again. The detector LED starts ﬂashing

and keypad display shows TEST IN PROGRESS.

Take badge reader to its intended mounting location

and make sure LED ﬂashes continuously, indicating good

communication with control panel.

Press Yes to end radio range test, then press Esc/No.

The display shows RECORDING A NEW DEVICE? Repeat

steps 4 - 8 for remaining badge readers.

When ﬁnished, exit from conﬁguration mode.

www.videofied.com

PRODUCT INSTALLATION SHEET

Badge Reader BR651

2208-BRIS March 2012Made by RSI VIDEO TECHNOLOGIES

Summary of content (6 pages)

PAGE 1
Badge Reader BR651 P R O D U C T I N S TA L L ATI O N S H E E T Made by RSI VIDEO TECHNOLOGIES 2208-BRIS March 2012 Product Summary Installation Guidelines The Outdoor Badge Reader BR651 is designed for use in operating a Videofied security system. The Outdoor Badge Reader includes the following features: For easier installation and programming, RF testing should be done to check for good communication between the control panel and all system devices before mounting system devices.
PAGE 2
Outdoor Badge Reader BR651 I N S TA L L ATI O N DATA S H E E T Mounting 1 Separate base from Badge Reader > Use proper tools and hardware. 2 Hold base up against mounting surface and mark the three mounting holes. 3 Drill pilot holes and install anchors where needed. Mouting holes 4 Place base on mounting surface so mounting holes line up with pilot holes/anchors and secure unit with appropriate screws. 5 Install batteries, observing correct polarity.
PAGE 3
Outdoor Badge Reader BR651 I N S TA L L ATI O N DATA S H E E T Recording a new badge With the keypad, go to the menu : Display of the keypad Actions and commentaries BADGES ACCES CODES ENTER A BADGE / CODE Place your badge on the reader until you hear two beeps then after a few seconds the display will change BADGE OR CODE CODE NAME Enter the name of the code and ACCESS 2 ENTRY COMPLETE Wait Delete a code With the keypad, go to the menu : Actions and commentaries Display of the keypad ENTER A
PAGE 4
Outdoor Badge Reader BR651 I N S TA L L ATI O N DATA S H E E T Functioning of indicators The complete functioning of the indicators is only possible with the XL / XT / XV / VISIO v5.2 / V6000 V31.02 or superior control panels. During arming During disarming When reading the badge, the reader emits a beep, then two beeps indicating the badge has been accepted.
PAGE 5
Outdoor Badge Reader BR651 Physical Data Electrical Data Panel Compatibility XL, Visio, XT, XTIP Power requirements Three 3.6 V batteries Nominal Voltage 3.6V Low Battery Limit 2.7V Battery type Up to 4 years RF technology S2View® Operating frequency Transmission security Supervision Antenna Tamper detection in. Installation/Mounting Unit/Base 2 screws secure the Badge Reader to the base. 3 screws secure base to flat mounting surface.
PAGE 6
Outdoor Proximity Reader Model BR651 PRODUCT SPECIFICATIO N SHEET FCC Regulatory Information for USA and CANADA FCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI VideoTechnologies may void the FCC authorization to operate this equipment. FCC Part 15.105 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.