Landscape Pro Slim Electric Fireplace Model# LPS-4414V2 LPS-5614V2 LPS-6814V2 LPS-8014V2 LPS-9614V2 OWNERS MANUAL V2 Rated: 120VAC 60Hz 5,000 BTUs WARNING Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in fire, electric shock, or serious personal injury. CAUTION Keep this owner’s manual for future reference. If you sell or give this product away, make sure this manual accompanies this product.
IMPORTANT SAFETY INFORMATION! WARNING When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all Instructions before installing or using the heater. 2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, etc. and curtains at l east 3 feet (0.
CONSIGNES IMPORTANTES ATTENTION Lors de l'utilisation d'appareils électriques, des précautions de base doivent toujours être suivies pour réduire les risques d'incendie, d'électrocution et de blessures, notamment les suivantes : 1. Lisez toutes les instructions avant d'installer ou d'utiliser le radiateur. 2. Ce radiateur est chaud lorsqu'il est utilisé. Pour éviter les brûlures, ne laissez pas la peau nue toucher les surfaces chaudes.
USER INSTRUCTIONS POWER DATA LPS-4414V2 LPS-5614V2 LPS-6814V2 LPS-8014V2 LPS-9614V2 AC 120Vs 60Hz 13 Amp AC 120V 60Hz 13 Amp AC 120V 60Hz 13 Amp AC 120V 60Hz 13 Amp AC 120V 60Hz 13 Amp Heater AC 120V 1465W AC 120V 1465W AC 120V 1465W AC 120V 1465W AC 120V 1465W BTUs 5,000 BTUs 5,000 BTUs 5,000 BTUs 5,000 BTUs 5,000 BTUs Lamps LED 12V LED 12V LED 12V LED 12V LED 12V Motor 12 VDC Stepper Motor 12 VDC Stepper Motor 12 VDC Stepper Motor 12 VDC Stepper Motor 12 VDC Stepper Motor
PRODUCT GUIDE 5 3 ⁄8" Model Viewing Area Firebox Dimensions Framing Dimensions LPS-4414V2 43 5⁄8" W x 13 5⁄8" H 44 1⁄16" W x 23 3⁄4" H x 5 3⁄8" D 44 1⁄4" W x 24 ¹⁄8" H x 6" D LPS-5614V2 LPS-6814V2 LPS-8014V2 LPS-9614V2 1111mm W x 356mm H 1124mm W x 603mm H x 141mm D 1130mm W x 613mm H x 152mm D 55 5⁄8" W x 13 5⁄8" H 56 1⁄16" W x 23 3⁄4" H x 5 3⁄8" D 56 1⁄4" W x 24 ¹⁄8" H x 6" D 1416mm W x 356mm H 1430mm W x 603mm H x 141mm D 1435mm W x 613mm H x 152mm D 67 5⁄8" W x 13 5⁄8" H 68 1⁄16" W
PARTS and HARDWARE (1) Fireplace (1) Owners Manual (1) L-Metal Mounting Bracket Set (1) Front Glass (1) Battery Tool (1) CR2025 Battery Smoke Acrylic Crystals Pkg Clear Acrylic Stones Pkg Wall Mount (1) Touch Control (Sold Separately) (1) Remote (1) Canyon Driftwood Logs Set (1) Suction Cup (1) Trim INSTALLATION Select a suitable location that is not susceptible to moisture and away from drapes, furniture, and high traffic areas. NOTE: Follow all national and local electrical codes.
INSTALLATION Due to the many different materials used on different walls, it is highly recommended that you consult your local builder before you install this fireplace. Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Check the parts list to make sure nothing is missing. Dispose of packaging materials properly. Please recycle whenever possible.
BUILT-IN INSTALLATION Fully Recessed Installation (Single Sided) 1. This installation is optimized for a 2x6 framed wall. Prepare the framed opening according to the framing dimensions chart (pg 4). *Provide appropriate dedicated circuit for hardwire install at the top right of framed opening. 2. Install L Metal mounting brackets to the top and bottom of the fireplace with supplied screws. 3. Hardwire fireplace (see page 6) 4.
BUILT-IN INSTALLATION Partial Recessed Installation 1. This installation is optimized for a 2x4 framed wall. Prepare the framed opening according to the framing dimensions chart on page 4. *Provide appropriate dedicated circuit for hardwire install at the top right of framed opening. 2. Install L Metal Nailing Flanges to the fireplace. 3. Hardwire fireplace (see page 6) 4. Install the fireplace in the framed opening with a minimum 1 1⁄4" drywall screws to secure the unit. 5.
LOG SETS #1 LOG #9 LOG #2 LOG #3 LOG #11 LOG #10 LOG #5 LOG #4 LOG #12 LOG #6 LOG #13 LOG #8 LOG #7 LOG #15 LOG #14 LOG #16 LOG LANDSCAPE PRO SLIM – LOG SET SIZES 44 – 56 – 68 – 80 – 96 LPS 44 – Set contains 6 logs #6 LOG #5 LOG #3 LOG #4 LOG #2 LOG #1 LOG LPS 56 – Set contains 8 logs #8 LOG #7 LOG #6 LOG #5 LOG #3 LOG #4 LOG #2 LOG #1 LOG LPS 68 – Set contains 10 logs #10 LOG #9 LOG #8 LOG #6 LOG #7 LOG #5 LOG #4 LOG #3 LOG #2 LOG #1 LOG LPS 80 – Set contains
LOG PLACEMENT LANDSCAPE PRO SLIM – LOG PLACEMENT 44" – 56" – 68" – 80" – 96" LPS 44" – Set contains 6 logs 3 4 6 1 5 2 LPS 56" – Set contains 8 logs 8 4 6 7 3 1 5 2 LPS 68" – Set contains 10 logs 8 9 4 6 7 10 1 3 5 2 LPS 80" – Set contains 12 logs 11 12 8 9 4 6 7 10 1 3 5 2 LPS 96" – Set contains 16 logs 13 16 15 14 12 11 9 8 4 7 10 10 6 5 3 1 2
INSTALLING MEDIA AND FRONT GLASS 1. Remove screws from top of glass bracket. Use the small suction cup provided in the hardware kit to lean glass towards the front. Then lift glass up and away. Place glass in soft, safe area. 2. The fireplace comes with clear and smoke crystals. Mix crystals together and evenly spread crystals along the ember bed. 3. Place the logs on top of the acrylic crystals. 4. The front glass can now be installed, by installing bottom of glass in track, then tilt towards fireplace.
REMOTE CONTROL OPERATION The unit has a main power switch just in front of the glass on the top right hand side. A hand-held remote is included. Power This will cycle the fireplace on and off. Upon cycling power on, the fireplace will return to the settings it had when it was cycled off . Home If the fireplace is on, this button will act as a reset and bring all colors back to the default Modern Flames' signature color. Heat This will cycle the heater between high, low and off .
SETTING CONTROLS Manual Controls Toggle Switch: The fireplace has a main toggle switch located next to the manual controls. The toggle switch is in front of the glass on the top right side of the viewing area. When the “-” side of the toggle switch is depressed, the “O” pops up. This is the power-on state of the fireplace. Power Indicator lights: The fireplace is equipped with Power indicator lights which are located on the upper right corner of the fireplace viewing area.
SETTING CONTROLS NOTE: When silent mode is selected, a tone will still be present for performing system functions such as remote pairing or Wi-Fi pairing. -AP Mode: While the fireplace is ON, long press the Preset Color button for 6 seconds. Two audible beeping tones will sound and then only the FLAME LIGHTS and nothing else will turn to white and begin flashing slowly. Fireplace is now in AP pairing mode, which lasts for 2 minutes.
WIFI REMOTE Sync This is a synchronization selector, used to synchronize the current color on the color wheel to all of the zones (Flame/Ember Bed/Downlight). Grayed out SYNC is when synchronization is “OFF”. Green SYNC is when synchronization is “ON”. Color Wheel This is the color adjustment wheel for all zones. Keeping contact on the color circle, the color of the selected zone will change continuously base on where you have your finger.
WIFI REMOTE Mode Sub Menu Preset Menu Mode Button > Island Time Opens a sub menu for selecting presets. Same as remote control blue monochrome fade cycle. PRESET MENU > Modern Flames Original > Seven Color Demo Same as remote control, 7 color jump cycles: R->G->B->RG->RB->GB->RGB. Modern Flames Orange (Static). > Three Color Demo > Horizon Same as remote control, 3 color jump cycles: R->G->B. > Trifecta Custom mode can be modified from “My Ambience” setting. The default color is Red.
WIFI REMOTE Timer Pressing the timer button will pop up a sub-menu with 10 options to choose from: 0.5-1-2-3-4-5-6-7-8 hours-cancel. Once the selected time has elapsed, the fireplace will turn off. (default) Ambience Setting The Ambience Setting button will open up a second window where customizations can be performed, including temperature scale setting (C/F), Weekly/Heat programming, Custom mode configuration, and changing speed of the flame and ember bed.
WIFI REMOTE Power Off Turn On Cancel Heat Level HEAT PROGRAM SUB MENU CONTINUED > Power Off Low Sets fireplace status (no heat) OFF/ON. > Heat Level High Sets Heat Level: OFF/LOW/HIGH. Cancel > Temperature Temperature Level for the heater to turn on if the ambient temperature falls below the set temperature (High Heat).
WIFI REMOTE > Mode Color Mode color: In the Static mode, only one color can be selected. After clicking the color symbol, you can change to additional colors. When using the Jump/Gradient feature, 8 colors can be programmed by clicking “+” color. By adjusting the color sliders, select the corresponding RGB value to obtain the desired color combination.. > Color Flash Mode Customizing how the color changes.
WIFI INITIAL LOG-IN Search for and install the “MODERN FLAMES” app from Google Play or Apple App store or scan the QR code. STEP 2 STEP 1 > After download & installed Login to Modern Flames app.
WIFI PAIRING STEP STEP 3 4 > Once opened and logged in > SELECT FIREPLACE From HOME page, From the home page, select the add “+” symbol. Select series of fireplace that will be pairing too and follow instructions.
WIFI REMOTE STEP STEP 5 6 > Ensure fireplace is ON > WiFi Information Using the fireplace manual touch controls, turn ON the fireplace. If pairing via Wi-Fi you must use 2.4 GHz Wi-Fi, and must have information filled out to move to next step.
WIFI REMOTE STEP STEP 7 8 > Wi-Fi Pairing confirmed > Place fireplace in pairing mode EZ pairing mode is confirmed with a single audible beeping tone is heard and all the lights begin to blink rapidly Once fireplace is “ON”, place fireplace in Wi-Fi pairing mode following the instructions for pairing mode on the APP. There are 3 types of pairing EZ mode, AP mode and a Bluetooth mode. EZ and AP modes will be displayed accordingly on the top right of the screen. Example displayed is EZ mode.
WIFI REMOTE STEP STEP 9 10 > PAIRING > DEVICE PAIRED SUCCESSFULLY Device & APP should now begin to pair. Depending on Wi-Fi this can take up the entire 2 minutes to pair, or it may need to be repeated more than once, if the signal isn’t captured the first time. NOTE: Do not turn off or disconnect the fireplace from power while pairing the Wi-Fi or performing updates. Failure to do so can result in damage to the electrical components of the fireplace.
!+#!!!(& ;DE<>D&A<=>;&=IEGD;! 456=$ 'AF /0123+ /0123$ /0123% /0123" /0123& /0123' /0123( /0123) /0123* /0123+! /0123++ /0123+$ /0123+% /0123+" /0123+& /0123+' !$#!!!!( ED>@/N&;DAD!!&G;@AMD>N&EC=?&KO2L !$#!!$'* !$#!!$(! !$#!!$') ED>@/&><'&G;@AD&:<;&?/@!!&:@AD !%#!!!&* !!!+!+ /&!D> !$#!!$'( !%#!!!&) A;B!>@/N
TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION A. Breaker tripped or circuit has no power B. Internal component is frozen and needs to be reset C. Loose connection D. Defective component A. Reset breaker, test circuit for power, check power switch B. Turn power off at the main breaker for 60 seconds. Turn power back on. C. Inspect wiring for loose or damaged connection D. Replace motherboard, touch control or power switch Touch Screen Comes on - then nothing A.
FREQUENTLY ASKED QUESTIONS Q. How do you change the optional Wall Touch Control to Fahrenheit/Celsius? A. Long press on the up and down arrows on the fire unit to toggle between Fahrenheit and Celsius. Q. What distance can the remote be used from the fireplace? A. Optimal distance for the remote control is maximum 20 feet. Q. Can you turn on the fireplace via the manual control and off via the remote (or vise versa)? A. Yes. Q. Can the fireplace be installed outside? A. No.
FCC CAUTION This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
DO NOT RETURN TO STORE! Thank you for choosing Modern Flames, we appreciate all our customers and hope you have many years of enjoyment of our products. STOP Take a look at our other products from our RPG Brands family of companies CALL US FIRST For immediate help with installation, product information or GrandCanyonGasLogs.com if your product arrives damaged, please call our toll free number at: )RU DOO \RXU LQGRRU RXWGRRU JDV ȴUHSODFHV ȴUH IHDWXUH SURGXFWV 1-877-246-9353 (Monday - Friday, 8:00AM -