IMPORTANT SAFETY INFORMATION * Read all of these instructions carefully, and save them for reference. Follow all warnings and instructions marked on the product, » Clip the swivel bass on to the monitor before installation. + Unplug the monitor from the system unit before cleaning. Do not usc liquid or aerosol cleaners. Use a damp cloth for cleaning. * Use only attachments recommended by the manufacturer; unapproved attachments may be hazardous.
* The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. » The monitor is equipped with a three-wire grounded plug, a plug with a third (grounding) pin. This is a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely.
hazards. Refer all servicing to qualified service personnel. * Unplug the monitor from the system unit and refer servicing to qualified service personnel under the following conditions: = When the power cord or plug is damaged or frayed. If liquid has been spilled into the monitor. If the monitor has been exposed to rain or water. If the monitor does not operate normally and you are following the operating instructions.
FCC Class B Radio Frequency Interference Statement NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation.
TABLE OF CONTENTS 1.GENERAL DESCRIPTION 1 2. PRODUCT PACKAGE 2 2.1 Installing and Removing the Swivel Base 2 3. INSTALLATION THE MONITOR 3 3.1 Safety Checks 3 3.2 Connecting the Video Cable . 3 3.3 Connecting the Power Cord . 4 PERPETRATION THE MONITOR 5 4.1 Control Keys Meaning . 5 4.2 On Screen Display (OSD) Message . 8 4.3 Auto Save Function... 8 4.4 Display Adjustment... Poor picture 6.3 Picture Locks or Center Shift 6.4 Picture is Too Large or Small 7. TECHNICAL INFORMATION 13 7.4 Precautions LL.
1. GENERAL DESCRIPTION This monitor is a high-performance intelligent multi-scan color monitor. It is designed to be compatible with all modes between 30 KHz and 70 KHz. The microprocessor-based design was implemented with the user in mind, providing digital user controls for precision, auto synchronization and auto-sizing for convenience, user improbability for flexibility, as well as built-in tilt and swivel base for comfort in prolonged usage.
2. PRODUCT PACKAGE Plan the most convenient location for your monitor and avoid using sharp object in opening the carton. Open the shipping cartons and check the contents of the package. The package should include the following items: « Swivel base * Monitor + Power cord If any items are missing, contact your supplier immediately. Remove the monitor from its shipping carton. Save the carton and packaging materials, in case you ever need to pack and relocate the monitor. 2.
3. INSTALLATION THE MONITOR 3.1 Safety Checks Make sure the monitor and system unit power switches are off, when you start connecting cables. This monitor is set for 100240 Vac 60/50 Hz (full range). Confirm the line voltage for your monitor by checking the voltage label on the rear panel of the monitor. USB CONNECTOR (OPTION) POWER IN VIDEO IN Figure 3 Connecting the Video Cable and Power Cord 3.2 Connecting the Video Cable The monitor comes with a built-in video cable.
3.3 Connecting the Power Cord CAUTION: If the AC inlet in your location does not provide for this type of grounded plug, make sure to install the proper adapter for a safety grounding. This monitor comes with a power cord. See Figure 3. Plug power cord into a computer's inlet. The three-wire power cord must be provided a safety precaution to ensure proper electrical grounding.
4. OPERATION THE MONITOR tor. The other control knobs are located at the base of the monitor. (See Figured) User could make a good appearance of the monitor to suit your personal preference by press these controls. |] Power Indicator Menu Select Standby Key Menu Select Brightness/Contrast Select Decrease Brightness/Contrast (up) increase/Enter Brightness/Contrast (Down) Figure 4 Power Switch and Control Knob 4.
Decrease To adjust function scale to smaller. Increase The key has two uses. 1. To adjust function scale to larger. 2. To select function (Recall, Degassed, Exit). 4.2 On Screen Display ( OSD ) Message The OSD is a message that displays on the monitor screen. The OSD message can show the function scale and the mode’s frequency. When user does not press key at 10 seconds later, the OSD message is been off. V-SIZE BEELINE CIO BIRDIEING Figure 5 The OSD Message 4.
Contrast Press © to show the contrast ® adjustment window of OSD message as figure 6. Press + to increase or to decrease the contrast level. OO GEOMETRY : V-size Repeatedly press < or > until the [Symbol changes color. Press + to increase or — to decrease the vertical size of the display. V-position 1 Repeatedly press < or > until the [81 symbol changes color. Press + to increase or — to lower the vertical position of the display. H-width & Repeatedly press < or > until the BB symbol changes color.
Balance (J Repeatedly press < or > until the (3 symbol changes color. Making the desired adjustment by pressing the keys adjust the balance of the display. Parallelogram 7 Repeatedly press < or > until /7th symbol changes color. Making the desired adjustment by pressing the keys adjust the parallelogram of the display. -.Moire til To adjust the moire of the display. Rotation EJ Repeatedly press < or > until the EJ symbol changes color.
3K COLOR : Press select 1. 9300° K (Factory preset) 2. 6500° K (Factory preset) 3. USER-1 (9300° K background color) 4. USER-2 (6500° K Background color) If choice 3 (USER-1) or 4 (USER-2) then press + key You can adjust R-gain, G-gain or B-gain. R-drive BI Repeatedly press < or > until the red symbol changes color. Making the desired adjustment by pressing the keys adjust Red-Gain. G-drive Repeatedly press < or > until the green symbol changes color.
050 POSITION Press select up, down or [3 left, right and press the key adjust the OSD position. ++ — [50+ + V.POSITION RE RECALL Press + to recall £7 GEOMETRY factory set. * VASE DIMS Press key +: On is enable / disable DIMS function change. £r DEGASSED Press + to manual degassed function OD MODE : information Show the current mode information: Zz includes the flowing. VF: 85.0 Hz Factory preset mode number or user H. SYNC mode number, V. SYNC H: Horizontal Sync frequency. V: Vertical Sync frequency. H.
5. POWER MANAGEMENT This monitor meets the power management standards as set by the Video Electronics Standards Association (VASE) and / or the United States Environmental Protection Agency (EPA). This feature is designed to conserve electrical energy by reducing power consumption. This function is active by an operating system or Windows utility program which turns off the monitor display and also turns off, or changes the color or the monitors power indicator.
6. TROUBLESHOOTING This section provides solutions to minor problems you may encounter when installing or using this monitor. If the problem persists after trying the suggestions in Table 1, contact your place of purchase. 6.1 No Picture = Check that both power and signal cables are securely connected. Adjust the brightness and contrast controls. 6.2 Poor Picture = Adjust the brightness and contrast controls. Check your display adapter configuration. (Refer to your display adapter manual.) 6.
7.TECHNICAL INFORMATION 7.1 Precautions + Only a qualified service technician should open the monitor case. Components inside the monitor can cause serious electric shock, Do not attempt to remove the back cover of the monitor by yourself. Contact your monitor dealer or authorized service personnel if your monitor needs to be repaired. * To prevent fire or shock hazard, do not expose this monitor to rain or moisture. 7.2 Specifications CRT: 1. Viewable Size: 40 em (15,87) max. Screen Diagonal 2.
Scanning Frequency: 1. Horizontal: 2. Vertical: Power Supply: 1. Input voltage: 2. Consumption: Environment: 1. Operating: Temperature: Humidity: 2. Non operating: Temperature: Humidity: Dimension: Weight: X-Radiation: 1. DHS 2. PTB (Self Certificate) Regulatory: 1 30 KHz ta 70 KHz 47 Hz to150 Hz 100-240 Vac 60/50 Hz 120 Watts maximum 0C topic 20% to 80% -20°C to 60°C 10% to 90% 408mm(W)x 421mm(H)x 426mm{D) (with base) Approx. 17kgs(NET) Optional Optional TUB-GS Optional TCO Optional NORDIC 6.