9〞 Digital Control Multiscan Color Green Monitor User’ s Guide C-986A 3H0F8N04N9
IMPORTANT SAFETY INFORMATION ˙ Read all of these instructions carefully, and save them for reference. Follow all warnings and instructions marked on the product. ˙ Clip the swivel bass on to the monitor before installation. ˙ Unplug the monitor from the system unit before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. ˙ Use only attachments recommended by the manufacturer; unapproved attachments may be hazardous.
˙ The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. ˙ The monitor is equipped with a three-wire grounded plug, a plug with a third (grounding) pin. This is a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely.
hazards. Refer all servicing to qualified service personnel. ˙ Unplug the monitor from the system unit and refer servicing to qualified service personnel under the following conditions: - When the power cord or plug is damaged or frayed. - If liquid has been spilled into the monitor. - If the monitor has been exposed to rain or water. - If the monitor does not operate normally and you are following the operating instructions.
FCC Class B Radio Frequency Interference Statement NOTE ： This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Doc compliance notice This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio interference Regulations of the Canadian Department of Communications. “ Le present appreil numerque n’ emet pas de bruits radioelectriques depassant les limites applicables aux areils numeriques de class B prescrites dans le reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada.
TABLE OF CONTENTS GENERAL DESCRIPTION . . . . . . . . . .. .... 1 PRODUCT PACKAGE . . . . . . . . . . . . . . . . . . . . . . 2 Installing and Removing the Swivel Base . . . . . . . . 2 INSTALLATION THE MONITOR . . . . . . . . . . . … . Safety Checks . . . . . . . . . . . . . . . . .. . . . . . . . .. Connecting the Video Cable . . . . . . . . . . . . . . .. . Connecting the Power Cord . . . . . . . . . . . . . . . .. . . . . 3 3 3 3 OPERATION THE MONITOR . . . . . . . . . .. . . . . . .
GENERAL DESCRIPTION This monitor is a high-performance intelligent multi-scan color monitor. It is designed to be compatible with all modes between 30 KHz and 86 KHz. The microprocessor-based design was implemented with the user in mind, providing digital user controls for precision, autosynchronization and auto-sizing for convenience, userprogrammability for flexibility, as well as built-in tilt and swivel base for comfort in prolonged usage.
PRODUCT PACKAGE Plan the most convenient location for your monitor and avoid using sharp object in opening the carton. Open the shipping cartons and check the contents of the package. The package should include the following items: ˙ Swivel base ˙ Monitor ˙ Power cord If any items are missing, contact your supplier immediately. Remove the monitor from its shipping carton. Save the carton and packaging materials, in case you ever need to pack and relocate the monitor.
INSTALLATION THE MONITOR Safety Checks Make sure the monitor and system unit power switches are off, when you start connecting cables. This monitor is set for 100240 Vac 60/50 Hz (full range). Confirm the line voltage for your monitor by checking the voltage label on the rear panel of the monitor. Figure 3 Connecting the Video Cable and Power Cord Connecting the Video Cable The monitor comes with a built-in video cable. To connect the video cable, follow the steps below: 1.
power cord into a computer’ s inlet. The three-wire power cord must be provided a safety precaution to ensure proper electrical grounding.
OPERATION THE MONITOR The power switch is Stand-by Power The other control knobs are located at the base of the monitor. (See Figure4) User could make a good appearance of the monitor to suit your personal preference by press these controls. Figure 4 Power Switch and Control Knob Control Keys Meaning Power Switch: Turn the monitor on or off. Power Indicator: Lights up when the power is ON. Brightness( －): Press－Key into brightness function. Press－to decrease or ＋to increase the display brightness level.
To adjust function scale to larger. To select function (Recall, Degauss, Exit). On Screen Display ( OSD ) Message The OSD is a message that displays on the monitor screen. The OSD message can show the function scale and the mode’ s frequency. When user does not press key at 10 seconds later, the OSD message is been off. Figure 5 The OSD Message Auto Save Function This monitor provides auto save function for saving any controls change. The auto save function acts when 1.
OSD message as figure6. Press ＋ to increase or － to decrease the contrast level. GEOMETRY : -V-size Repeatedly press < or > until the symbol changes color. Press + to increase or – to decrease the vertical size of the display. -V-position Repeatedly press < or > until the symbol changes color. Press + to move up or – to lower the vertical position of the display. -H-width Repeatedly press < or > until the symbol changes color. Press + to increase or – to decrease the horizontal width of the display.
Repeatedly press < or > until the symbol changes color. Making the desired adjustment by pressing the keys + or – to adjust the parallelogram of the display. - Corner Repeatedly press < or > until the symbol changes color. Making the desired adjustment by pressing the keys + or – to adjust the Corner of the display. -Rotation Repeatedly press < or > until the symbol changes color. Making the desired adjustment by pressing the keys + or – to adjust the Rotation of the display.
Making the desired adjustment by pressing the keys + or – to adjust Green-Gain. -B-gain Repeatedly press > until the blue symbol changes color. Making the desired adjustment by pressing the keys + or – to adjust Blue-Gain. -Return Press < or > until the symbol change color and press + to return the color sub menu. OSD position Press < or > to select up/down or the key + or – to adjust the OSD position. left/right and press Recall Press + to recall Geometry factory set.
POWER MANAGEMENT This monitor meets the power management standards as set by the Video Electronics Standards Association (VESA) and / or the United States Environmental Protection Agency (EPA). This feature is designed to conserve electrical energy by reducing power consumption. This function is active by an operating system or Windows utility program which turns off the monitor display and also turns off, or changes the color or the monitors power indicator.
TROUBLE SHOOTING This section provides solutions to minor problems you may encounter when installing or using this monitor. If the problem persists after trying the suggestions in Table 1, contact your place of purchase. No Picture - Check that both power and signal cables are securely connected. Adjust the brightness and contrast controls. Poor Picture - Adjust the brightness and contrast controls. Check your display adapter configuration. (Refer to your display adapter manual.
TECHNICAL INFORMATION Precautions ˙ Only a qualified service technician should open the monitor case. Components inside the monitor can cause serious electric shock. Do not attempt to remove the back cover of the monitor by yourself. Contact your monitor dealer or authorized service personnel if your monitor needs to be repaired. ˙ To prevent fire or shock hazard, do not expose this monitor to rain or moisture. Specifications CRT: 1. Viewable Size 2. Deflection 3. Dot pitch 4. Phosphor 5. Surface 6.
Scanning Frequency: 1. Horizontal : 30 KHz to 86 KHz 2. Vertical : 50 Hz to 160 Hz Power Supply: 1. Input voltage 2. Consumption Environment: 1. Operating - Temperature - Humidity 2. Nonoperating - Temperature - Humidity : 100-240 Vac 60/50 Hz : 120 Watts maximum : 0℃ to 35℃ : 10% to 90% : -25℃ to 60℃ : 10% to 90% Dimension: 445mm(W)x 459mm(H)x 479mm(D) (with base) Weight: Approx.18.4kgs(NET) X-Radiation: DHHS Regulatory: 1. Optional FCC-B/UL/CSA 2. Optional TÜV-GS 3. Optional MPR II(MPR 1990:10) 4.
Display Mode HOR/Ver Interlaced(I) Standard Resolution Frequency Non-Interlaced(NI) NI IBM/VGA 720x400 31.5KHz / 70Hz NI IBM/VGA 640x480 31.5KHz / 60Hz 640x480 37.5KHz / 75Hz NI VESA/75 VESA/85 640x480 43.3KHz / 85Hz NI NI VESA/75 800x600 46.9KHz / 75Hz NI VESA/85 800x600 53.7KHz / 85Hz NI VESA/75 1024x768 60.0KHz / 75Hz NI VESA/85 1024x768 68.7KHz / 85Hz VESA/75 1280x1024 79.9KHz / 75Hz NI NI VESA/65 1024x768 80.7KHz / 100Hz Video Pin Assignments D-Type 15-Pin Connector Pinout Pin no.
