USER MANUAL Please Read Automatic Input Voltage Detection DC12V/24V Universal Kit, Suitable for Cars, Compatible with Vans, Truck And Buses most Dashcams Voltage Cut-Off to Prevent Battery Drain Constant Power Includes 2 Sets of 4 Supply Types of Fuses & Piggy Back Fuse Cables www.rovedashcam.
EXPERIENCING ? PROBLEMS Item NOT as described? Damaged or defective? Missing items? Any issues what so ever? CONTACT US BEFORE RETURNING THE ITEM WE WILL HELP YOU IN RESOLVING ANY ISSUES ASAP CUSTOMER SERVICE Hours: Mon - Fri 9am-5pm PST Email Us Text Us Response in just 6 hours help@rovedashcam.com For faster response text us 1 (401) 484-ROVE(7683) Scan the Code to Email us Scan the Code to Text us help@rovedashcam.
WATCH HOW TO INSTALL Visit our website www.rovedashcam.com/pages/videos INSTALLATION INPUT 12V/24V 2A POWER GND ACC OUTPUT 5V 2A 3-LEAD HARDWIRE KIT FOR 24-HR AUTO TRIGGER PARKING MONITOR Designed to work with any Dash Cam BATTERY DRAIN PROTECTION STARTING AT 11.8V 12.0V 12.2V 12.4V 23.6V 24.0V 24.4V 24.8V www.rovedashcam.com Understanding ROVE Ultimate 3-Lead Hardwire Kit Watch HOW-TO INSTALL to learn & understand all the features so you can get the maximum benefit out of it.
INDE What Is Hardwire Kit? .................................................... 4 Features ............................................................................. 4 Low Voltage Protec�on ................................................ 4 Over current/Surge Protec�on .................................... 4 Universal Compa�bility ................................................ 5 Mul� Input Power DC 12v/24v ..................................... 5 Parking Mode Switch ......................................
The ROVE Ul�mate 3-Lead Hardwire Kit is a power management device that provides power to your dashcam from your car’s ba�ery via fuse box to keep your dashcam con�nuously running even a�er your engine is turned off to u�lize the 24HR Parking Monitor feature. LOW VOLTAGE PROTECTION The ROVE Ul�mate 3-Lead Hardwire Kit will monitor your voltage status and cut-off the power to the dashcam if the voltage drops below the configured value. This minimum voltage cut-off is 11.8VDC for a 12VDC ba�ery and 23.
OVER CURRENT/SURGE PROTECTION The ROVE Ul�mate 3-Lead Hardwire Kit can detect abnormal over voltage status and cut off power to prevent any damage to your dashcam. Addi�onally, the ROVE Hardwire Kit has built-in extra fuse box (2A) to have extra protec�on. UNIVERSAL COMPATIBILITY - With Mini USB Dash Cams The ROVE Ul�mate 3-Lead Hardwire Kit is compa�ble with all ROVE Dash Cams and also compa�ble with most other dash cameras available in the market that has a mini USB power connector.
Total Cable Length: 4 Meters (input 1 meter, output 3 meters) Input Wires: POWER/GROUND/ACC Input Voltage: Typical DC 12/24V, MAX DC 36V, auto detec�ng Output Connector: Mini USB plug, DC 5V, 2A Ba�ery Drain Protec�on Op�ons: 11.8V/12.0V/12.2V/12.4V for 12V Ba�ery 23.6V/24.0V/24.4V/24.8V for 24V Ba�ery Working temperature: -200 C to 600 C (-40 F to 1400 F) Control Box Dimension: 40 X 25 X 15mm Net Weight: 0.6 Ibs (0.
UNIVERSAL COMPATIBILITY CHART The Camera With Parking Guard Func�on Will Connec�on Method While Driving Constant Power Ground ACC Power INPUT 12V/24V 2A POWER GND ACC OUTPUT 5V 2A Constant Power Ground X INPUT 12V/24V 2A POWER GND ACC OUTPUT 5V 2A Constant Power www.rovedashcam.com INPUT 12V/24V 2A POWER GND ACC OUTPUT 5V 2A ACC Power www.rovedashcam.com INPUT 12V/24V 2A POWER GND ACC OUTPUT 5V 2A X www.rovedashcam.
WARNINGS WARNING Failure to comply with safety warnings and precau�ons can result in serious injury or death. BEFORE YOU BEGIN - We recommend that this type of HARD WIRE KIT installa�on should be performed by a qualified individual or professional business only. Working with your vehicle's power system can be dangerous to both you and your vehicle’s safety. If you do not know what you are doing or If you have any doubts, please consult a professional. HANDLING & PRECAUTIONS Handle your device with care.
Do NOT drop, puncture or disassemble this product. Keep out of reach of children. Do NOT try to open or repair it yourself. If the accessories, or the device has any problems, then contact the seller for assistance. Secure the device well with included cable �es to make sure it is not loose or fall down. This may create obstruc�on in opera�ng your vehicle. The company is NOT responsible for the loss of any data or your content during opera�on or in any circumstances.
ACC GND POWER 5V 2A 12V/24V 2A INPUT OUTPUT www.rovedashcam.com 11.8V 12.0V 12.2V 12.4V 23.6V 24.0V 24.4V 24.
The Hardwire Kit will protect your dashcam from draining your vehicle’s ba�ery. If ba�ery voltage gets too low, ROVE Hardwire Kit will stop powering your camera to save enough power, so you can start your car for the next �me. Now once you start to drive your car and when the ba�ery star�ng to charge and when the voltage reaches higher than the set cut-off voltage protec�on, then the hardwire kit will resume it’s func�on normally, un�ll again the voltage reaches the cut-off level.
There are 2 main stages in the hardwire kit installa�on. Connec�ng input cables to your fuse box and grounding. Connec�ng output cable to your dashcam.
1 LOCATE YOUR FUSE BOX Locate your fuse box using your Fuse Box Diagram. This informa�on can usually be found in your vehicle’s Owner’s User Manual or from your manufacturer’s website. Fuse box is located behid this panel. (Example Shown: Honda Civic) NOTE: To Determine the location of your vehicle’s fuse box refer to the vehicle owner’s manual. It will instruct you on how to get access to your fuse box. In above case, we have removed the top panel to get access to the fuse box.
2 FIND THE CORRECT FUSE SLOT FOR YOUR HARDWIRE KIT The next thing to do is to understand which fuse slot to use. You will need to find two fuse slots to be used in this step. 1 A fuse Slot that provides constant power (RED wire will go here) A Fuse Slot that only provides power when you turn your key to ACC posi�on (YELLOW wire will go here) 2 Make a note of these as you will need to refer this back in step 4 part 2, and step 5.
For ROVE Ul�mate 3-lead hardwiring kit, there are 3 wires that need to be connected: RED Wire A�aches to the Constant Power Fuse Slot (Always Hot - means this fuse always provides power even when your car key is locked and turned off). YELLOW Wire A�aches to the ACC Power [Igni�on-Switched Fuse Means this Fuse slot only provide power when you turn your car’s key from LOCK posi�on to ACC posi�on]. BLACK Wire A�aches to the Metal Grounding Screw/Bolt.
3 IDENTIFY THE CORRECT TYPE OF FUSE FOR YOUR CAR Now, once you have iden�fied which fuse slots you need to use, let’s find out the type of Add-A-Fuse / Piggy-Back Fuse Tap to use for your car’s model. As you can see in the below pictures, there are mainly four types of fuse used for American cars. There are few quick and easy way to iden�fy the type of fuse that your car uses. 1 Remove one of the fuses from your car’s fuse box and match it with one of the fuses in the picture below.
4 INSERT RED, YELLOW & BLACK CABLES 1 Now lets connect and then the RED & Yellow Wires securely with piggyback fuse-taps using a crimp tool or a pair of pliers. Connect the hard wire with Add-A-Fuse Crimp the Add-A-Fuse to secure the connec�on Fig: Crimp the fuse taps with Red & Yellow wires REMINDER If you are using the previously iden�fied fuse slot that has exis�ng fuse in it, then insert that fuse into the lower slot of the Add-A-Fuse with correct orienta�on.
Fig: Add-A-Fuse / Piggyback Fuse Tap 2 Now simply insert the piggyback fuse tap into the previously iden�fied Fuse Slots. RED Constant Power BLACK Ground YELLOW ACC 18 INPUT 12V/24V 2A POWER GND ACC OUTPUT 5V 2A www.rovedashcam.com 3-LEAD HARDWIRE KIT FOR 24-HR AUTO TRIGGER PARKING MONITOR Designed to work with any Dash Cam BATTERY DRAIN PROTECTION STARTING AT 11.8V 12.0V 12.2V 12.4V 23.6V 24.0V 24.4V 24.
5 LOCATING A GROUND POINT Now, let’s connect the BLACK Wire to the Grounding Screw or Bolt. Bad Grounding Choice (Screw on Plas�c) GOOD GROUNDING CHOICE (Screw on Metal Chassis) NOTE: See the picture above for reference. We recommend that you choose the metal Chassis Grounding Screw, or it may cause your dash cam to not function properly and restart/reboot when power does not flow properly.
6 TUCKING UP AND ROUTING THE CABLES NEATLY Now, let’s test the dash cam. Once you have hooked up all three wires (Red, Yellow and Black) to proper posi�ons, plug the Mini-USB cable into the camera and then start your vehicle to test the dash cam and parking mode. Make sure to turn ON the parking mode feature from your dash cam’s se�ngs. If the test passes then Voila..., You did it, Great Job.
Thank you for purchasing your ROVE Ul�mate 3-Lead Hardwire Kit. We hope you find your Hardwire Kit useful and fun to use. If you are having difficul�es se�ng up this hardwire kit, please email us at help@rovedashcam.com. 99% of all setup problems can easily be resolved and should be able to get you up and running in no �me. In the unlikely event that we can't help, we're always happy to provide a full, hassle-free refund. We just want our customers to be happy and proud to use ROVE Products.
www.rovedashcam.