POWER 1 2 3 4 5 6 7 8 9 +10 0 MEM FRQ DIRECT TUNE PRESET FM MONO BAND X ON OFF CH VOL SMART SMT MUTE GUIDE MENU C M CTR OSD ENT AUD CD V1 V2 SEARCH- SEARCH+ S R SUB SUR TUN TAPE EXT DEVICE / INPUT V3 V4 V5 RR-1061 RR-1061 Universal Learning Remote Control
RR-1061 Layout Disposition des commandes POWER 1 2 3 4 5 6 7 8 9 +10 0 MEM FRQ DIRECT TUNE PRESET FM MONO BAND X ON OFF CH VOL SMART SMT GUIDE MUTE MENU C M CTR OSD ENT AUD CD SEARCH- SEARCH+ S R SUB SUR TUN TAPE EXT DEVICE / INPUT V1 V2 V3 RR-1061 V4 V5
POWER 1 2 3 4 5 6 7 8 9 +10 0 MEM FRQ DIRECT TUNE PRESET FM MONO BAND X ON OFF CH VOL SMART SMT GUIDE MUTE MENU C M CTR OSD ENT SEARCH- SEARCH+ S R SUB SUR CD DISC1 DISC2 DISC3 DISC4 EQ DYN REC ZONE SUR+ DISC- DISC+ PROG RANDOM REPEAT 2CH DISC5 PL C PL M 5CH 7CH DIGEST TITLE P-SCAN OPEN DISPLAY AUDIO ANGLE SBTITLE ZOOM DISP TAPE2 PHONO TONE D-SLT A-B GOTO SLOW P-TUN TP TA DVD RESUME REPEAT SCAN PTY INPUT 1 INPUT 2
RR-1061 Flip Down Cover Volet rabattable LIGHT LIGHT R
Character Map Jeu des caractères affichés Learning Commands Apprentissage de commandes POWER 1 2 3 4 5 6 7 8 +10 0 FRQ DIRECT ON OFF CH VOL 9 MEM SMART X SMT GUIDE M CTR TUNE MUTE MENU C OSD PRESET ENT FM MONO BAND AUD CD V1 V2 SEARCH- SEARCH+ S R SUB SUR TUN TAPE EXT DEVICE / INPUT V3 V4 V5
RR-1061 Contents Layout Flip Down Cover Character Map Learning Commands 2 4 5 5 Introduction .............................................................. 8 Key Features 8 Sensible Precautions 8 Battery Installation 8 Overview ..................................................................
5/22/08 11:28:03 AM English 7 Learning Commands From Another Remote ............... 20 Learning Commands 567-q 20 Multi-Step Button Learning = 21 Smart Macro Programming ...................................... 22 Smart Macro Programming 567-q 22 Clearing a Smart Macro 56-q 23 Changing a Smart Macro 56-q 23 Clearing Learned commands .....................................
RR-1061 Introduction The RR-1061 Universal Learning Remote Control can replace up to nine remote controls, operating A/V components from Rotel or other brands. Key Features • Programmed to operate Rotel surround sound processors, receivers, and DVD players. • Simple programming for hundreds of components using built-in codes. • Learning function to teach the RR-1061 commands from other remotes. Multi-step learning on five buttons for multiple command sequences from other remotes.
English 9 Overview The RR-1061 is a universal learning remote control that can operate all of the components in your audio/video system. Control codes for Rotel components are already programmed. You can easily customize the RR-1061 to operate other components by selecting command sets for hundreds of components from the RR-1061’s extensive database. See the Programming section of this manual for easy to follow instructions.
RR-1061 Folding Cover w A folding cover conceals the buttons at the bottom of the RR-1061. These buttons provide extra command functions. Leave the folding cover in the closed position to simplify the RR-1061 for routine use. Open the cover to access the additional buttons.
English EXT Button 11 4 The EXT button is a special input selection button for Rotel audio/video receivers or surround sound processors. It is used to select the multi-channel analog inputs when playing SACD or DVD-A discs. This bypasses the digital/analog processing in the receiver or surround sound processor. Press and hold the EXT button for more than one second to select the multi-channel analog input on a Rotel A/V receiver.
RR-1061 At the bottom right are nine buttons that duplicate the cursor functions for cable or satellite TV receiver or audio/video components plus four round buttons are for extra functions, such as Last Channel, Viewing Guide, etc. At the bottom left are five oval buttons that duplicate the basic transport control functions (Play, Fast Forward, Pause, etc.) of a CD player, DVD player or video tape recorder. NOTE: The numeric buttons, 0 – 9, are also avail- able for sending Smart Macros.
English 13 Operating the RR-1061 This section of the manual explains the basic operation of the RR-1061 and most of its standard features. NOTE: The AUD DEVICE/INPUT button of the RR-1061 is pre-programmed with control codes for Rotel A/V receivers or surround sound processors. The V1 button is pre-programmed to operate Rotel DVD players. The CD button is pre-programmed to operate Rotel CD players. The other DEVICE/INPUT buttons (TUN, TAPE and V2 – V5) are unprogrammed.
RR-1061 pressed the correct DEVICE/INPUT button and use the button labels as guides. When a button is pressed, a beep tone confirmation is heard. This feature can be disabled. See the Disabling the Beep Tone section of the manual. When an IR command is being sent, a triangular indicator appears in the upper right corner of the LCD display and the label for the command is shown in the display. These labels can be customized. See the Labelling Command Buttons section of this manual.
5/22/08 11:28:04 AM English 15 Programming The RR-1061 contains hundreds of command sets for components. Programming the remote involves selecting the command sets that correspond to the components in your system and assigning each of them to one of the nine DEVICE buttons by entering the 4-digit code for that component. This need only be done once during initial setup of the RR-1061. There are four ways of finding the correct 4-digit code.
RR-1061 1. Press the DEVICE/INPUT button where you wish to program this component’s code (AUD, CD, TUN, TAPE and V1–V5). 2. Press the SETUP button (the LCD displays SETUP). Press the ENT button to confirm. 3. Press the UP/DOWN cursor buttons until SETUP MODEL appears in the display. Press the ENT button to confirm. 4. Press the UP/DOWN cursor buttons until the type of component you are searching for appears in the display (AUD, DVD, CD) Press the ENT button to confirm.
English 17 To program using the brand search: 1. Press the DEVICE/INPUT button where you wish to program this component’s codes (AUD, CD, TUN, TAPE and V1–V5). 2. Press the SETUP button (the LCD displays SETUP). Press the ENT button to confirm. 3. Press the UP/DOWN cursor buttons until SETUP BRAND appears in the display. Press the ENT button to confirm. 4. Press the UP/DOWN cursor buttons until the type of component you are searching for appears in the display (TV, VCR, SAT, CTV, DVD, CD, etc.
RR-1061 Programming by 4-Digit Code 567-q Find your audio/video component in the 4-digit code list. Then proceed as follows: 1. Press the DEVICE/INPUT button where you wish to program this component’s codes (AUD, CD, TUN, TAPE and V1–V5). 2. Press the SETUP button (the LCD displays SETUP). Press the ENT button to confirm. 3. Press the UP/DOWN cursor buttons until SETUP CODE appears in the display. Press the ENT button to confirm. 4. Input the 4-digit code using the 0–9 buttons.
RR-1061 5/22/08 11:28:04 - En-Fr - a.indd AM Spread 19 of 32 - Pages(46, 19) English 19 Programming by Auto-Search 56789-q To search for a code from the full list of available 4-digit codes for a type of component: 1. Press the DEVICE/INPUT button where you wish to program this component’s codes (AUD, CD, TUN, TAPE and V1–V5). 2. Press the SETUP button (the LCD displays SETUP). Press the ENT button to confirm. 3. Press the UP/DOWN cursor buttons until SETUP A. SEARCH appears in the display.
RR-1061 Learning Commands From Another Remote If you are unable to find a command set using the Programming steps, or if you need additional commands, you can teach the RR-1061 commands directly from your existing remotes. This procedure is called Learning. Learning Commands 567-q To teach the RR-1061 the commands from one of your other remotes, place the two remote controls end to end as shown in the illustration at the front of this manual.
RR-1061 - En-Fr - a.indd Spread 21 of 32 - Pages(44, 21) English 21 NOTE: The RR-1061 has enough memory to learn 600 commands. If the memory capacity is reached, the LCD displays FULL when you attempt to learn a command. Multi-Step Button Learning = The five buttons labeled SCAN, PTY, P-TUN, TP, TA provide a special option – the ability to learn up to three different commands on a single button.
RR-1061 Smart Macro Programming Twenty of the buttons on the RR-1061 (the 10 DEVICE/INPUT buttons plus the numeric buttons 0 – 9) can store multiple command macro sequences – for example, a sequence that turns on the TV set, selects channel 5, turns on the surround processor, and selects the TV input. Smart Macro Programming 567-q A macro sequence is sent by pressing the SMART button followed by the button where the macro is stored.
English Clearing a Smart Macro 23 56-q To clear a previously saved Smart Macro: 1. Press the SETUP button and then press the UP/ DOWN cursor buttons until SMART appears in the display. Press ENT. 2. Press the UP/DOWN cursor buttons until SMART CLEAR appears in the display. Press the ENT button to confirm. CLEAR SMART? appears in the display. 3. Press the Smart Macro button to be cleared (for example, press 1 to clear a Smart Macro stored in the 1 button). 4. A confirmation appears in the LCD.
RR-1061 7. A confirmation appears in the LCD. Use the UP/DOWN buttons to select either YES (to change the command) or NO (to discard the changes). Press ENT to confirm. NOTE: If you attempt to change an unprogrammed Smart Macro button, the word EMPTY appears and the remote returns to normal mode.
RR-1061 - En-Fr - a.indd Spread 25 of 32 - Pages(40, 25) English 25 3. Press the UP/DOWN cursor buttons until CLEAR ONE DEV appears in the display. 4. Press the ENT button to delete all learned commands for the DEVICE/INPUT button. Clearing All Learned Commands for ALL DEVICE/INPUT Buttons -q 1. Press the SETUP button (the LCD displays SETUP). Press the UP/DOWN cursor buttons until EDIT appears in the display. Press the ENT button to confirm. 2.
RR-1061 Editing DEVICE/INPUT button labels 5-q To change the label for a button, make sure that you have selected the Page 2 set of labels (see above), then: 1. Press the SETUP button. 2. Press the UP/DOWN cursor buttons until EDIT appears in the display. Press the ENT button to confirm. 3. Press the UP/DOWN cursor buttons until EDIT DEVICE appears in the display. Press the ENT button to confirm. 4. Press the DEVICE/INPUT button (AUD, CD, TUN, TAPE, EXT, V1–V5) that you wish to relabel.
English 27 5. Press the COMMAND button that you wish to relabel. The current label appears on the second line of the display. 6. Press the +/– buttons to select a character to change and the UP/DOWN cursor buttons to change the letter. The “Character Map” illustration shows the available characters. Labels can be a maximum of 8 characters. 7. When the new label is complete, press the SETUP button to save the new label. 8. A confirmation message appears in the LCD.
RR-1061 Additional Setup Options Volume/Mute Punch-Through 9-q In many systems, the volume is adjusted at the TV set or the A/V processor. For convenience, the RR-1061 has a Volume Punch-Through feature that copies the volume and mute commands from either the TV device or AUD to DEVICE/INPUT buttons for other components such as CD players, VCRs, SAT receivers, and DVD players.
English Disabling the Beep Tone 29 -q As shipped from the factory, the RR-1061 beeps as confirmation whenever a button is pressed. This feature can be disabled or enabled as follows: 1. Press the SETUP button (the LCD displays SETUP). 2. Press the UP/DOWN cursor buttons until BEEP SOUND appears in the display. Press the ENT button to confirm. 3. Press the UP/DOWN cursor buttons until BEEP ON or BEEP OFF appears in the display. Press the ENT button to select the desired option.
RR-1061 Clone Function -q The CLONE function transfers all programming, learned commands, labels, and settings from one RR-1061 to a second RR-1061. To transfer the programming, place two RR-1061 remotes with their IR windows facing each other about 2 to 3 inches apart, then proceed as follows. On the remote that will be receiving the data: 1. Press the SETUP button. 2. Press the UP/DOWN cursor buttons until CLONE appears in the display. Press the ENT button to confirm. 3.
English 31 After 30 seconds or when any button is pressed, the remotes return to normal operation. NOTE: Do not attempt to use the CLONE function to transfer data from any remote other than another Rotel RR-1061. Restore Factory Defaults -q You can restore the RR-1061 to the factory default configuration with a simple procedure described below.
The Rotel Co. Ltd. 10-10 Shinsen-Cho Shibuya-Ku Tokyo 150-0045 Japan Phone: +81 3-5458-5325 Fax: +81 3-5458-5310 Rotel of America 54 Concord Street North Reading, MA 01864-2699 USA Phone: +1 978-664-3820 Fax: +1 978-664-4109 Rotel Europe Dale Road Worthing, West Sussex BN11 2BH England Phone: +44 (0)1903 221600 Fax: +44 (0)1903 221525 Rotel Deutschland Kleine Heide 12 D-33790 Halle/Westf. Germany Phone: +49 05201-87170 Fax: +49 05201-73370 www.rotel.