A14MKII Owner’s Manual Manuel de l’utilisateur Bedienungsanleitung Manual de Instrucciones Gebruikershandleiding Manuale di istruzioni Instruktionsbok Инструкция пользователя Stereo Integrated Amplifier Amplificateur Stéréo Intégré Stereo-Vollverstärker Amplificador Integrado Estereofónico Geïntegreerde stereoversterker Amplificatore integrato stereo Integrerad stereoförstärkare Интегрированный стерео усилитель
A14MKII Stereo Integrated Amplifier 2 Important Safety Instructions Notice You must allow a minimum 10 cm or 4 inches of unobstructed clearance around the unit. The RS232 connection should be handled by authorized persons only. WARNING: There are no user serviceable parts inside. Refer all servicing to qualified service personnel. WARNING: To reduce the risk of fire or electric shock, do not expose the unit to moisture or water. Do not expose the unit to dripping or splashing.
Figure 1: Controls and Connections Commandes et Branchements Bedienelemente und Anschlüsse Controles y Conexiones Controlli e connessioni De bedieningsorganen en aansluitingen Kontroller och anslutningar Органы управления и разъемы 2 34 1 5 6 7 POWER SPEAKERS PHONES A14MKII A B PHONO TUNER CD USB OPT COAX AUX PC-USB BT MENU 5V / 2.1A 9 8 0 - =q w e [ r t y u ] i \ o p a s
A14MKII Stereo Integrated Amplifier 4 Figure 2: Remote Control RR-AX1400 Télécommande infra-rouge RR-AX1400 Fernbedienung RR-AX1400 Mando a Distancia RR-AX1400 Telecomando RR-AX1400 De afstandsbediening RR-AX1400 Fjärrkontroll RR-AX1400 Пульт ДУ RR-AX1400 A J B K C L M D E F N G H I
Figure 3: Preamp Input and Speaker Output Connections Branchements des entrées sources et sorties enceintes acoustiques Anschlussdiagramm Conexiones para Entrada de Señal y Salida a las Cajas Acústicas Collegamenti ingressi e diffusori De signaalingangen en de luidsprekeruitgangen Signal- och högtalaranslutningar Подсоединение источников сигнала и акустических систем Amplifier A14MKII CD PLAYER PHONO
A14MKII Stereo Integrated Amplifier 6 Figure 4: Digital Input Connections Branchements Entrées numériques Digitaleingänge-Anschlüsse Conexiones Entradas Digitales Digitale ingang verbinding Collegamenti ingressi digitali Anslutningar för digitala ingångar Подсоединение Цифровые входы Computer (Supplied) Amplifier A14MKII CD Player CD14 CLASS 1 LASER PRODUCT APPAREIL LASER DE CLASSE 1 MODEL NO.
Figure 5: 12V Trigger Connections Branchementstrigger 12 V 12V-Trigger-Anschlüsse Conexiones para Señal de Disparo de 12V De 12V trigger aansluitingen Collegamenti segnali Trigger 12 V 12 V-anslutning för styrsignal Подсоединение 12-В триггерного сигнала Amplifier A14MKII Tuner T14 WIFI ANTENNA WIFI ANTENNA OUTPUT ANTENNA L COAXIAL OUT NETWORK TUNER T14 USB FM DAB RS232 ROTEL LINK 12V TRIGGER R OUT OUT IN OUT
A14MKII Stereo Integrated Amplifier Important Notes When making connections be sure to: 4 Turn off all the components in the system before hooking up any components, including loudspeakers. 4 Turn off all components in the system before changing any of the connections to the system. It is also recommended that you: 4 Turn the volume control of the amplifier all the way down before the amplifier is turned on or off.
Contents About Rotel Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Figure 1: Controls and Connections 3 Figure 2: Remote Control RR-AX1400 4 Figure 3: Preamp Input and Speaker Output Connections 5 Figure 4: Digital Input Connections 6 Figure 5: 12V Trigger Connections 7 Important Notes 8 About Rotel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A14MKII Stereo Integrated Amplifier 10 A Few Precautions WARNING: To avoid potential damage to your system, turn off ALL the components in the system when connecting or disconnecting the loudspeakers or any associated components. Do not turn the system components back on until you are sure all the connections are correct and secure. Pay particular attention to the speaker wires. There must be no loose strands that could contact the other speaker wires, or the chassis of the amplifier.
Protection Indicator 2 Preamp Output [ The amplifier has both thermal and over-current protection circuitry that protects the amplifier against damage in the event of extreme or faulty operating conditions. The protection circuits are independent of the audio signal and have no impact on sonic performance. Instead, the protection circuits monitor the temperature of the output devices and shut down the amplifier if temperatures exceed safe limits.
A14MKII Stereo Integrated Amplifier 12 If you are using terminal lugs, connect them to the wires. If you are attaching bare wires directly to the binding posts, separate the wire conductors and strip the insulation from the end of each conductor. Be careful not to cut into the wire strands. Unscrew (turn counterclockwise) the binding post thumbscrews. Place the connector lug or wire around the binding post shaft. Turn the thumbscrews clockwise to clamp the connector lug or wire firmly in place.
sparingly. Be particularly careful when turning the controls up. This increases the power output in the bass or treble range, increasing the load on the amplifier and speakers. NOTE: Setting the Bass and Treble controls do not automatically turn on the tone control. To turn on tone control, refer to previous section Tone Control Bypass. Source Input Selector 8I Press the corresponding input button on the front panel 8 or remote control I to select the desired listening source.
Settings Menu You can access the SETUP menu from the front panel by pressing the MENU 9 button or the K button on the remote. You can change the value of the selected option by pressing the - or + buttons on the front panel or the up/down/left/right C arrow buttons on the remote. Step through the sub-menus by pressing the MENU 9 button on the front panel or the K button on the remote. • T ONE BYPASS: TONE BYPASS on/off (For more information refer to Tone Control Bypass section).
• COAX1 VOL: VARIABLE (disabled) is factory default. • COAX2 VOL: VARIABLE (disabled) is factory default. • BTOOTH VOL: VARIABLE (disabled) is factory default. NOTE: For more information regarding network connection please contact your authorized Rotel dealer. NOTE: A network connection is not required for the A14MKII to operate. NOTE: The Volume knob on the front panel and Volume +/- buttons on the IR remote are disabled when the volume is Fixed.
A14MKII Stereo Integrated Amplifier 16 No Sound Check the signal source to see if it is functioning properly. Make sure the cables from the signal source to the amplifier inputs are connected properly. Be sure the Input Source is set to the proper input. Check the wiring between the amplifier and the speakers. Cannot Connect via Bluetooth USB Apple (iPhone, iPod, iPad) Format Notes Any suppor ted file loaded to Apple device. Any supported file loaded to Apple device.
The Rotel Co. Ltd. Tachikawa Bldg. 1F., 2-11-4, Nakane, Meguro-ku, Tokyo, 152-0031 Japan Rotel USA Sumiko 6655 Wedgwood RD N, Suite 115 Maple Grove, MN 55311 USA Phone: (510) 843-4500 (option 2) E-mail: service@sumikoaudio.net “Made for iPod,” and “Made for iPhone,” means that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards.
