User's Manual

ManualsBrandsRosslare Enterprises ManualsElectronicsProximity and Keypad Reader

Table Of Contents

AYC-F64

PROXIMITY CARD &

BACKLIT KEYPAD READER

WIEGAND AND CLOCK & DATA

INSTRUCTION MANUAL

07/04

www.rosslaresecurity.com

0706-0960044-00

FCC part 15 statement and warnings

NOTE: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Warning!

Changes or modifications to this equipment not expressly approved by

Rosslare Enterprises Ltd. could void the user’s authority to operate the

equipment.

Warning!

This product was tested with shielded cables, which must be used with

the unit to insure compliance.

Summary of content (13 pages)

PAGE 1
FCC part 15 statement and warnings NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 2
Introduction Contents INTRODUCTION 3 4 5 Technical Specifications Key Features INSTALLATION Mounting the AYC-F64 reader Wiring the AYC-F64 reader The AYC-F64 is a waterproof programmable Wiegand and Clock & Data proximity card and keypad reader. The AYC-F64 supports multiple Proximity Card and Keypad formats providing a high level of compatibility and connectivity with host controllers.
PAGE 3
Environmental Characteristics Technical Specification Operating Temperature: -22 F to 150 F (-30 C to 65 C) Electrical Characteristics Operating Voltage Range: 5 to 16V DC From a Regulated Power Supply (Linear type recommended) Operating Humidity: 0 to 95% (Non-Condensing) Suitable for outdoor use. (IP 65) Maximum Input Current: Standby: 85mA Max: 95mA Mechanical Characteristics Not including attached devices Not including attached devices Dimensions: 4.72" (120mm) L x 2.80" (71mm) W x 0.
PAGE 4
Wiring the AYC-F64 Installation The reader is supplied with a 16-inch pigtail, having a 6-conductor cable. To connect the reader to the Controller, perform the following steps. Mounting the AYC-F64 Controller 1) Before starting, select the location to mount the AYC-F64 reader. This location should be at shoulder height. 2) For wall mounting use the mounting template as a guide to drill the mounting and cable holes in the wall.
PAGE 5
Transmit Mode Programming the AYC-F64 When the AYC-F64 is in Transmit Mode, it is ready to receive data from a presented Proximity Card or an entered PIN code. When the reader is in Transmit Mode, the Transmit LED is red and the Program LED is off Transmit Program RED When a Proximity Card or Keyboard entry is being transmitted, the Transmit LED will flash green. Programming the AYC-F64 is done solely via the unit's keypad driven Programming Menu System.
PAGE 6
Selecting Keypad Transmission Format Entering Programming Mode 1) Press the "#" key 4 times.  Transmit LED will turn off  Program LED will turn red Transmit 2) Enter your 4-digit Programming Code. Program RED 1 2 Transmit If the Programming Code is valid the Program LED will turn green and the AYC-F64 will be in Programming Mode. 3 The AYC-F64 has eight different keypad transmission formats to select from.
PAGE 7
Keypad Transmission Format Option Number OPTION 2 Single Key, 6-Bit Wiegand, Nibble & Parities See the table below to determine the Option Number for the Keypad Transmission Format you wish to select. Each key press immediately sends 4 bits with 2 parity bits added. Even parity for the first 3 bits and odd parity for the last 3 bits.
PAGE 8
The keypad PIN code must be 4 digits long and can range between 0001 and 9999. On the fourth key press of the 4 digit PIN code, the data is sent across the Wiegand Data lines as binary data in the same format as a 26-Bit Card. If the " " key or the "#" key are pressed during PIN code entry or a PIN code greater than 65,535 is entered, the keypad will clear the PIN code entry buffer, generate a beep and is ready to receive a new 4 digit keypad PIN code.
PAGE 9
OPTION 7 Single Key, 3x4 Matrix Keypad (MD-P64) This unique mode is intended to let the host controller scan the AYC-F64's keypad while still keeping the proximity card readers 26Bit Wiegand or Clock & Data formats active. An optional interface board must be used between the AYC-F64 and the host system. Each key press is immediately sent on DATA0 as an ASCII character at a baud rate of 9600 bits per second.
PAGE 10
Proximity Card Transmission Format Option Number PIN Data : (EP) 0000 AAAA BBBB CCCC DDDD EEEE (OP) where A =The first key entered. D =Fourth key entered. B =Second key entered. E =Fifth key entered. C =Third key entered. EP =Even parity for first 12 bits. OP =Odd parity for last 12 bits. OPTION 1 26-Bit Wiegand OPTION 2 Clock & Data OPTION 3 Wiegand Card + PIN If the PIN code is less than 5 digits, all the most significant nibbles are filled with 0.
PAGE 11
2) Press "0" to enter Menu 0  The Transmit LED will flash red  The Program LED will flash red Changing the Facility Code Transmit 1) Enter Programming Mode Program GREEN 2) Press "4" to enter Menu 4 3) Enter your 4-digit Programming Code. 4  The Transmit LED will Transmit flash orange.
PAGE 12
Limited Lifetime Warranty LIMITED LIFETIME WARRANTY TERMS ,, ROSSLARE ENTERPRISES LIMITED S (Rosslare) LIMITED LIFETIME WARRANTY is applicable worldwide. This warranty supersedes any other warranty. Rosslare's LIMITED LIFETIME WARRANTY is subject to the following conditions: WARRANTY Warranty of Rosslare's products extends to the original purchaser of the Rosslare product and is not transferable.
PAGE 13
Technical Support International: Rosslare Enterprises Ltd. 905-912 Wing Fat Industrial Bldg., 12 Wang Tai Road, Kowloon Bay, Hong Kong. http://www.rosslaresecurity.com Tel: Fax: E-mail: (852) 2795 5630 (852) 2795 1508 info@rosslare.com.hk United States and Canada: Rosslare America, Inc. 1600 Hart Court, Suite 103, Southlake, TX 48091 USA http://www.rosslaresecurity.com Tel: Tel: Fax: E-mail: AYC-F64 (866) 262 8633 (Toll-Free) (817) 305 0006 (Direct) (817) 305 0069 support@rosslare.