ADC-8434-A Quad Analog Audio to AES Converter User Manual
ADC-8434-A User Manual • Ross Part Number: 8434ADR-004-01 • Release Date: April 2, 2012. The information in this manual is subject to change without notice or obligation. Copyright © 2012 Ross Video Limited. All rights reserved. Contents of this publication may not be reproduced in any form without the written permission of Ross Video Limited. Reproduction or reverse engineering of copyrighted software is prohibited.
Important Regulatory and Safety Notices to Service Personnel Before using this product and nay associated equipment, refer to the “Important Safety Instructions” listed below to avoid personnel injury and to prevent product damage. Product may require specific equipment, and/or installation procedures to be carried out to satisfy certain regulatory compliance requirements. Notices have been included in this publication to call attention to these specific requirements.
EMC Notices United States of America FCC Part 15 This equipment has been tested and found to comply with the limits for a class A Digital device, pursant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Environmental Information The equipment that you purchased required the extraction and use of natural resources for its production. It may contain hazardous substances that could impact health and the environment. To avoid the potential release of those substances into the environment and to diminsh the need for the extraction of natural resources, Ross Video encourages you to use the appropriate take-back systems.
Company Address Ross Video Limited Ross Video Incorporated 8 John Street P.O. Box 880 Iroquois, Ontario, K0E 1K0 Ogdensburg, New York Canada USA 13669-0880 General Business Office: (+1) 613 • 652 • 4886 Fax: (+1) 613 • 652 • 4425 Technical Support: (+1) 613 • 652 • 4886 After Hours Emergency: (+1) 613 • 349 • 0006 E-mail (Technical Support): techsupport@rossvideo.com E-mail (General Information): solutions@rossvideo.com Website: http://www.rossvideo.
Contents Introduction 1 Overview.............................................................................................................................. 1-2 Features.................................................................................................................. 1-2 Functional Block Diagram................................................................................................... 1-3 User Interfaces ...........................................................................
ii • Contents ADC-8434-A User Manual (Iss.
Introduction In This Chapter This chapter contains the following sections: • Overview • Functional Block Diagram • User Interfaces • Documentation Terms and Conventions A Word of Thanks Congratulations on choosing an openGear ADC-8434-A Quad Analog Audio to AES Converter. Your ADC-8434-A is part of a full line of Digital Products within the openGear Terminal Equipment family of products, backed by Ross Video's experience in engineering and design expertise since 1974.
Overview The ADC-8434-A Quad Analog Audio to AES Converter is a broadcast quality, modular product used to convert four analog audio channels to two, 24-bit, unbalanced AES-3id signals. The ADC-8434-A accepts 4 analog audio signals (2 stereo pairs) and provides 2 copies of each of the 2 AES / EBU output signals. The conversion from analog to digital is performed with 24-bit precision.
Functional Block Diagram This section provides a functional block diagram that outlines the workflow of the ADC-8434-A. Figure 1.1 Simplified Block Diagram — 8310AR-036 and 8320AR-036 Full Rear Modules ADC-8434-A User Manual (Iss.
User Interfaces The ADC-8434-A offers the following interfaces for control and monitoring. DashBoard Control System™ The DashBoard Control System™ enables you to monitor and control openGear frames and cards from a computer. DashBoard communicates with other cards in the DFR-8300 series frame through the MFC-8300 Series Network Controller Card. For More Information... • on the menus in DashBoard, refer to the chapter “DashBoard Menus” on page 4-1.
Documentation Terms and Conventions The following terms and conventions are used throughout this manual: • “Board”, and “Card” refer to openGear terminal devices within openGear frames, including all components and switches. • “DashBoard” refers to the DashBoard Control System™. • “DFR-8300 series frame” refers to all versions of the 10-slot (DFR-8310 series frames) and 20-slot (DFR-8321 series frames) frames and any available options unless otherwise noted.
1–6 • Introduction ADC-8434-A User Manual (Iss.
Installation In This Chapter This chapter provides instructions for installing the Rear Module(s) for the ADC-8434-A, installing the card into the frame, and cabling details. The following topics are discussed: • Before You Begin • Installing the ADC-8434-A • Cabling for the ADC-8434-A • Software Upgrades for the ADC-8434-A ADC-8434-A User Manual (Iss.
Before You Begin Before proceeding with the instructions in this chapter, ensure that your DFR-8300 series frame is properly installed according to the instructions in the DFR-8300 Series User Manual. Static Discharge Throughout this chapter, please heed the following cautionary note: ESD Susceptibility — Static discharge can cause serious damage to sensitive semiconductor devices. Avoid handling circuit boards in high static environments such as carpeted areas and when synthetic fiber clothing is worn.
Installing the ADC-8434-A This section outlines how to install a Rear Module in a DFR-8300 series frame. The same procedure applies regardless of the frame or card type. However, the specific Rear Module you need to install depends on the frame you are using. Note that Slot 1 is the left most slot as you look into the openGear frame from the front. Rear Modules for the ADC-8434-A The Rear Module for the ADC-8434-A depends on the openGear frame you are installing the card into.
5. Using a Phillips screwdriver and the supplied screw, fasten the Rear Module to the back plane of the frame. Do not over tighten. 6. Ensure proper frame cooling and ventilation by having all rear frame slots covered with Rear Modules or Blank Plates. Installing the ADC-8434-A Use the following procedure to install the ADC-8434-A in a DFR-8300 series frame: 1. Locate the Rear Module you installed in the procedure “Installing a Rear Module” on page 2-3. 2.
Cabling for the ADC-8434-A This section provides information for connecting cables to the installed Rear Modules on the DFR-8300 series frames. Connect the input and output cables according to the following sections. DFR-8310 Series Frame Cabling Overview In the DFR-8310 series frames, the ADC-8434-A is used with the following Rear Modules: • 8310AR-036 Rear Module — Each module occupies one slot and accommodates one card.
Software Upgrades for the ADC-8434-A The card can be upgraded in the field via the MFC-8300 series Network Controller card in your frame. Note — DashBoard version 3.0.0 or higher is required for this procedure. To upgrade the software on a card 1. Contact Ross Technical Support for the latest software version file. 2. Display the Device View of the card by double-clicking its status indicator in the Basic Tree View. 3. From the Device View, click Upload to display the Select file for upload dialog. 4.
User Controls In This Chapter This chapter provides a general overview of the user controls available on the ADC-8434-A. The following topics are discussed: • Card Overview • Configuring the DIP Switches • Control and Monitoring Features ADC-8434-A User Manual (Iss.
Card Overview This section provides a general overview of the ADC-8434-A components. Figure 3.1 ADC-8434-A — Components SW1 — Remote Control Use SW1 to disable remote control of the ADC-8434-A from DashBoard. Set SW1 as follows: • ON — Select this setting to disable remote control from DashBoard. The parameters and settings cannot be changed via DashBoard and must be changed using the card-edge controls. You can still monitor the status of the card using DashBoard.
SW7, SW8 — Output Mode Selection 2 SW7 and SW8 are used in conjunction to set the output mode of the second audio converter. Refer to the section “Setting the Output Modes” on page 3-4 for details. SW9, SW10 — Input Level Selection SW9 and SW10 are used in conjunction to specify the input level (+4dB). Refer to the section “Setting the Nominal Input Level” on page 3-4 for details. ADC-8434-A User Manual (Iss.
Configuring the DIP Switches This section provides a brief summary of the DIP switches of the ADC-8434-A. Refer to Figure 3.1 for DIP Switch locations. Figure 3.2 shows all the DIP Switches in the OFF position. ON 1 2 3 4 5 6 7 8 9 10 Figure 3.2 Jumper and Switch Locations Enabling Card-edge Control Ensure that SW1 is set to ON and SW2 is set to ON if you are going to use the card-edge DIP Switches to change settings on the card. You can still monitor the card status in DashBoard.
Control and Monitoring Features This section provides information on the LEDs for the ADC-8434-A. Refer to Figure 3.3 for the location of the LEDs. Figure 3.3 ADC-8434-A Card-edge Controls Status LEDs on the ADC-8434-A The front-edge of the ADC-8434-A has LED indicators for the communication activity. Basic LED displays and descriptions are provided in Table 3.4. Table 3.
3–6 • User Controls ADC-8434-A User Manual (Iss.
DashBoard Menus In This Chapter This chapter provides a summary of the menus available for the ADC-8434-A. Parameters noted with an asterisk (*) are the default values. The following topics are discussed: • Status Tabs • Settings Tab ADC-8434-A User Manual (Iss.
Status Tabs The Status tabs provide read-only information such as software revision issue, signal status, and power consumption of the ADC-8434-A. Card Info Tab Table 4.1 summarizes the read-only information displayed in the Card Info tab. Table 4.1 Card Info Tab Items Tab Title Card Info (Read-only) Item Parameters Description Card Name Quad Analog Audio to AES Converter Product ADC-8434-A Supplier Ross Video Ltd. Serial Number # Indicates the serial number of the board Software Rev ##.
Settings Tab Table 4.3 summarizes the Settings options available in DashBoard. Table 4.
4–4 • DashBoard Menus ADC-8434-A User Manual (Iss.
Specifications In This Chapter This chapter provides the technical specifications for the ADC-8434-A. Note that specifications are subject to change without notice. The following topics are discussed: • Technical Specifications ADC-8434-A User Manual (Iss.
Technical Specifications This section provides the technical specifications for the ADC-8434-A. Table 5.
Service Information In This Chapter This chapter contains the following sections: • Troubleshooting Checklist • Warranty and Repair Policy ADC-8434-A User Manual (Iss.
Troubleshooting Checklist Routine maintenance to this openGear product is not required. In the event of problems with your ADC-8434-A, the following basic troubleshooting checklist may help identify the source of the problem. If the frame still does not appear to be working properly after checking all possible causes, please contact your openGear products distributor, or the Technical Support department at the numbers listed under the “Contact Us” section. 1.
Warranty and Repair Policy The ADC-8434-A is warranted to be free of any defect with respect to performance, quality, reliability, and workmanship for a period of FIVE (5) years from the date of shipment from our factory. In the event that your ADC-8434-A proves to be defective in any way during this warranty period, Ross Video Limited reserves the right to repair or replace this piece of equipment with a unit of equal or superior performance characteristics.
Contact Us Contact our friendly and professional support representatives for the following: • Name and address of your local dealer • Product information and pricing • Technical support • Upcoming trade show information Telephone: +1 613 • 652 • 4886 Technical Support After Hours Emergency: +1 613 • 349 • 0006 Email: techsupport@rossvideo.com Telephone: +1 613 • 652 • 4886 General Information Fax: +1 613 • 652 • 4425 Email: solutions@rossvideo.com Website: http://www.rossvideo.
