Warning! Table of Contents THE 410X DVD/CD/MP3 PLAYER IS DESIGNED TO ENABLE VIEWING OF DVD OR CD-VIDEO RECORDINGS ONLY FOR REAR-SEAT OCCUPANTS. Introduction ........................................................................ 2 MOBILE VIDEO PRODUCTS ARE NOT INTENDED FOR VIEWING BY THE DRIVER WHILE THE VEHICLE IS IN MOTION. SUCH USE MAY DISTRACT THE DRIVER OR INTERFERE WITH THE DRIVER’S SAFE OPERATION OF THE VEHICLE, AND THUS RESULT IN SERIOUS INJURY OR DEATH. SUCH USE MAY ALSO VIOLATE STATE LAW.
INTRODUCTION The 410X is a full-featured disc player, supporting DVD, CDVideo, CD-Audio, and MP3 playback, and is designed specifically for the mobile environment. It is intended for use with other Rosen/necvox products and Rosen/necvox video monitors, and can also be integrated with many other products as part of a complete mobile video solution. With a digital audio output, the 410X can also support use of optional digital audio processors.
FCC Approval This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Do not attempt to open the unit or the remote control. The internal parts are not serviceable by the user. Opening any of the components will void the warranty. THE 410X IS A CLASS I LASER PRODUCT, USING A LASER WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF IMPROPERLY DISASSEMBLED. All service should be performed by authorized Rosen service centers or other qualified service personnel.
the DVD disc does not correspond to the Region number of this player (Region 1), this player will not be able to play the DVD disc. Some DVD discs are manufactured to operate in “all” zones, and those discs are compatible with the 410X. USING THE 410X In order to operate the 410X, the vehicle ignition key switch must be in the ACC or engine ON position.
The Nav Keys are used to navigate disc-generated menus and setup menus of the 410X. Front-Panel Controls Previous Disc slot Eject button Stop Next For information on using the rest of the front-panel controls, please see the sections describing disc playback. Play/ Pause Power The IR Receiver detects the signals from the included infrared remote control. Aim the remote control at the IR receiver during use.
Using the Remote Control THE REMOTE CONTROL Aim the remote control towards the IR receiver on the front panel. The remote control can operate at a 30-degree angle from the front of the unit.
DVD/VCD/CD-AUDIO PLAYBACK Disc Playback Inserting a DVD/VCD/CD DVD playback will often begin automatically when the disc is inserted. With some DVD discs, you will need to press [ENTER] or [ ] to begin playback. 1 Turn the vehicle’s ignition key to the ACC or ON position. ACC or engine ON position 2 Press either the [ON] button on the front panel or the [POWER] button on the remote control. CD-Audio discs will begin playback automatically.
Moving to the Previous Track or Chapter Press the [PREVIOUS] button during playback. The first time this button is pressed, playback of the current track or chapter will restart from the beginning. Pressing this button again will cause the previous track or chapter to be played. Note: • For some VCD 2.0 discs, the [PREVIOUS] and [NEXT] functions may be unavailable. Fast Searching During Playback Press [ ] and [ ] during playback to rapidly search for a particular section of a DVD or CD.
Parental Control The Parental Control feature allows authorized users to select an upper limit to film ratings that can be played by the 410X. If a DVD is inserted with a film rating higher than that selected, the following screen appears: The parental setting of this player prohibits play. Would you like this disc to play? YES NO In order for the film to play, the viewer must select “Yes,” and then the four-digit numeric “password” must be entered.
MP3 PLAYBACK ON CD-R DISCS - - SMART NAVI - ROOT What is MP3? MP3 is an audio compression method. This audio compression method has become a standard format with many PC users. MP3 allows the original digital audio data to be compressed to about 10 percent of its initial file size while still retaining high sound quality. This means that about 10 music CDs can be recorded on a CD-R disc, thus allowing longer listening time without having to change CDs.
File Extensions Always add a file extension “ .MP3” or “.mp3” to an MP3 file by using single-byte letters. If you add a different file extension, or forget to add the file extension “ .MP3” or “.mp3,” the file cannot be played. In addition, if you use upper case and lower case letters (capital and small letters) mixed together for file extensions, normal play may not be possible.
Installation and Wiring 2. Package Contents 1. Before Starting • • • • • • • • Read these instructions and the following precautions carefully. WARNING! Be sure to disconnect the battery (-) terminal before starting. This is to prevent short circuits during installation. 410XR disc unit IR Remote control 4-pin Power Supply harness RCA Audio Cable Additional IR Receiver (with cable) Installation Brackets and Assorted Hardware Owner’s Manual / Installation Guide Warranty Card 3.
4. Installing the 410X Rear fastening hole of vehicle, or backstrap Installing into the DIN Sleeve Instrument panel Hole First, verify that the opening you will be mounting the 410X into will accommodate the mounting sleeve. Sleeve opening dimensions Hole Bend tabs to lock sleeve into place 2-1/16" (53 mm) 7-3/16" (182 mm) Nut and washer Rear mounting bolt Note: • DIN mounting sleeve Some car models require special mounting kits for proper installation.
Removing the 410X from the DIN Mounting Sleeve Installing into a Fixed In-Dash Mount Note: Some vehicles use the “ISO” standard radio-mounting system. ISO-style factory radio locations use right-angle brackets that mount to the instrument panel, behind a trim ring. ISO mounting systems are typically found in Asiandesigned vehicles. • This requires you to have the original release tools provided with the 410X. Keep these tools in a safe place, not in the vehicle. 1 Remove the rear nut.
2 Remove the clips on the sides of the 410X. 3 Mount the unit to the factory radio brackets, and bolt the brackets to the dashboard. Reassemble the dash. Note: • 2-Screw DIN sleeve spring clip In some cases the factory trim panel may require some slight trimming, or there may be a slight gap that requires filling.
5. Wiring the 410X Factory Radio Mounting Screws (retain) Factory Radio Mounting Bracket (1 pair for the left and right sides) The following pages display wiring diagrams for 410X configurations. Read the following precautions before wiring your system. • Disconnect the negative battery terminal before making any wiring connections. 410X Pocket Factory Trim Bezel • Be particularly careful where you route wires. Keep them away from the engine, exhaust system, etc. Heat may damage wires.
410X Rear-panel Connections Audio L and R Output (White - L, Red - R) Video Output (Yellow) Optional External IR input NOTE: Not all Rosen/necvox four-pin connectors use identical wire assignments ONLY USE THE FOUR-PIN CONNECTOR SUPPLIED WITH THIS UNIT! Black - Ground Yellow +12V Main Power 18 410X Wire side of Power Connector: Red +12V Accessory Four-pin Power Connector Digital optical output Fuse/ filter box Yellow +12V Main power Red +12V Accessory Black - Ground
410X in a typical system To Radio and Antenna Monitor FM Mod Power Supply Module for Monitor Video Output (Yellow) Power Harness, Monitor Optional External IR input Audio L and R Output (White - L, Red - R) Digital output Fuse/ filter box Power Harness, 410X Black - Ground Red +12V Accessory Yellow +12V Main power 410X 19
SETUP 410X Typical Setup and Configuration The 410X is shipped with the following configuration: • Standard 4:3 aspect ratio format output • Automatic NTSC/PAL output switching Changing Settings The following sections explain how to customize various features of the 410X. To change settings for your 410X: 1 Press [SETUP]. 2 Use the [ ] and [ ] buttons to highlight a selection. 3 Press the [ENT] button to confirm your selection.
Changing the Aspect Ratio Mode Changing the Video Output Mode To change the aspect ratio mode, select GENERAL, and then select TV DISPLAY. For widescreen (16:9) monitors, select WIDE. For standard monitors and letterbox viewing (black bars on the top and bottom of the screen, but the entire image preserved), select NORMAL/LB. For standard 4:3 monitors and a full-screen image, but with the edges variably cropped to fit (“pan-and-scan” mode), select NORMAL/PS.
Concealing the “Angle Mark” Activating Captions and Subtitles To display or conceal the “angle mark,” which appears during scenes that support the multiple-viewing-angle feature, select GENERAL and ANGLE MARK. To enable or disable captions or subtitles, select GENERAL and CAPTIONS. Note: • - - GENERAL PAGE - TV DISPLAY TV TYPE ANGLE MARK OSD LANG CAPTIONS SCR SAVER MAIN PAGE ON OFF If CAPTIONS is set to OFF, the [SUBTITLE] button will be defeated from working.
Activating the Digital Output Selecting an LPCM Output Frequency To turn on the digital output, select AUDIO and AUDIO OUT. To select an LPCM output frequency (when a digital audio processor is in use), select AUDIO and LPCM OUTPUT. Note: • Only enable the digital output when a digital audio processor is in use. Some digital audio processors will require you to select an LPCM output frequency.
Deactivating the “Smart Nav” On-Screen Menu Display Changing Language Settings To play MP3 discs without the “Smart Nav” on-screen menu display, select PREFERENCES, then SMART NAV. Several language settings can be customized on the 410X. Notes: - - PREFERENCES PAGE - AUDIO SUBTITLE DISC MENU LOCALE PARENTAL PASSWORD SMART NAV DEFAULTS MAIN PAGE • Not all language settings are supported by all discs. • The languages supported by the 410X vary by individual option setting.
To change the soundtrack language, select PREFERENCES and AUDIO. - - PREFERENCES PAGE - AUDIO SUBTITLE DISC MENU LOCALE PARENTAL PASSWORD SMART NAV DEFAULTS MAIN PAGE ENGLISH FRENCH SPANISH CHINESE JAPANESE To change the disc menu language, select PREFERENCES and DISC MENU. - - PREFERENCES PAGE - AUDIO SUBTITLE DISC MENU LOCALE PARENTAL PASSWORD SMART NAV DEFAULTS MAIN PAGE ENGLISH FRENCH SPANISH CHINESE JAPANESE GERMAN ITALIAN To change the subtitle or caption language, select PREFERENCES and SUBTITLE.
Setup Options List The factory default options are given in bold type. GENERAL PAGE TV DISPLAY: NORMAL/PS, NORMAL/LB, WIDE.
TROUBLESHOOTING SPECIFICATIONS “Tinny” sound. Supply voltage: 12V DC Nominal, 11-16V operating voltage* Temperature: 0o to 50o Celsius* Current consumption: Less than 3.0A Check the “Downmix” setting in the SETUP menus and ensure that it is set to “Stereo,” not “LT/RT.” Picture “rolls.” Check that the TV Type setting is correct for the monitors being used. (See “Changing the Video Output Mode”.) PAL video often “rolls” on NTSC monitors.
410X