UltraVista SX VIDEO WALL CONTROLLER Installation and Operations Manual Part Number VWL-S122DV 10707 Stancliff Road Houston, Texas 77099 Phone: (281) 933-7673 WWW.ROSE.
WARRANTY Rose Electronics® warrants the UltraVista™ SX to be in good working order for one year from the date of purchase from Rose Electronics or an authorized dealer. Should this product fail to be in good working order at any time during this one-year warranty period, Rose Electronics will, at its option, repair or replace the Unit as set forth below. Repair parts and replacement units will be either reconditioned or new. All replaced parts become the property of Rose Electronics.
TABLE of CONTENTS Contents Page # Disclaimer ...................................................................................................... 1 System Introduction ....................................................................................... 1 Features ..................................................................................................... 2 Package Contents ...................................................................................... 2 Rose Electronics web site .....
INTRODUCTION Disclaimer While every precaution has been taken in the preparation of this manual, the manufacturer assumes no responsibility for errors or omissions. Neither does the manufacturer assume any liability for damages resulting from the use of the information contained herein. The manufacturer reserves the right to change the specifications, functions, or circuitry of the product without notice.
Features Single-Link DVI-D input Supports analog and digital LCD displays Supports resolutions from 800 x 600 to 1920 x 1200 / 1080 p/i Input source is displayed on 4 displays, each showing ¼ of the image (2 x 2 video wall) Easy, simple installation No additional hardware or software needed Learn mode for obtaining the DDC specifications (DDC table) from a PC, Mac, or from the connected monitors Ideal for: Video walls Information displays Training / education centers Convention cent
OVERVIEW System Overview The UltraVista SX is a versatile and dynamic video wall system that can be easily and quickly set up in almost any location. The UltraVista SX can take any DVI-D source (video or image) and display it on a 2x2 video array. Each display monitor shows ¼ of the original video source using real-time scaling while maintaining the original resolution on all monitors. Resolutions from 800 x 600 to 1920 x 1200 are fully supported for both analog and DVI LCD displays.
INSTALLATION UltraVista SX Installation Installation of the UltraVista SX consists of: 1. Connect your single-link DVI-D video source to the DVI-I input connector on the rear panel of the UltraVista SX using a DVI-D mm cable. (Optionally, connect to a 1x2 DVI video splitter as shown) (NOTE: The connectors on the UltraVista SX are DVI-I connectors but the input video must be single-link DVI-D) 2. Connect four displays to the output connectors on the rear panel.
To set the UltraVista SX up to “Learn” the monitor specifications (DDC), press and hold both the SCROLL and ENTER buttons on the front panel until the set-up menu displays on the front panel LCD screen. Press the SCROLL button to cycle through the options. When the needed Learn mode is displayed (Learn PC, Learn Mac, Learn Screen, or Exit), press Enter to execute the learn function. The unit will obtain the DDC information from the selected source and return to normal operation.
TROUBLESHOOTING System Troubleshooting No Image on one or more monitors Check that the monitor is turned on Check that the power source for the monitor is turned on Make sure the LCD panel power cables are securely fastened to the monitor and to the power source Check the monitor connection to the UltraVista SX Verify an output image is present from the video source 6 INSTALLATION and OPERATIONS MANUAL
SAFETY Safety The UltraVista SX has been tested for conformance to safety regulations and requirements, and has been certified for international use. Like all electronic equipment, the UltraVista SX should be used with care. To protect yourself from possible injury and to minimize the risk of damage to the Unit, read and follow these safety instructions. Follow all instructions and warnings marked on this Unit.
SERVICE Service Information Maintenance and Repair This Unit does not contain any internal user-serviceable parts. In the event a Unit needs repair or maintenance, you must first obtain a Return Authorization (RA) number from Rose Electronics or an authorized repair center. This Return Authorization number must appear on the outside of the shipping container. See Limited Warranty for more information.
APPENDICES Appendix A- General Specifications Input 1 x DVI-D Single-Link Resolution 1920 x 1200 @ 60Hz (DVI-D or VGA) Outputs 4 x DVI or VGA (VGA requires a DVI to VGA adapter) Dimensions W D H 17.0in 7.0in 1.75in 43.2cm 17.8cm 4.45cm Weight 2.3 lbs / 1.04 kg Power Adapter Input 90 VAC to 264 VAC / 47 Hz to 63 Hz Power Adapter Output 5.0VDC / 3.0A Operating Temp.
Appendix B- Part Numbers Part Number Description VWL-S122DV 2 x 2 Video wall CAB-DVIIMMxxx DVI-I male to male cable CAB-DVIDMMxxx DVI-D male to male cable (xxx = length of cable in feet) 10 INSTALLATION and OPERATIONS MANUAL
10707 Stancliff Road Houston, Texas 77099 Phone: (281) 933-7673 WWW.ROSE.