V. Installation and Operation of Printer §.1 Printer Unpacking Check the parts: Before use, make sure the accessories are included in the package(the following picture is an example). If any thing is missing, contact the supplier or manufacturer. The specific accessories may not be included depending on the printer model. FL se © Main machine Power adapter Power cord Paper roll Communication cable € The pictures ara for clearance only, plans subject to practicality. 5.
A Attention: (1) First plug the power plug DC24V of the printer, then switch on the AC220V power supply, and then turn on the power switch. Do not reverse the sequence, otherwise the machine will ba damaged. (2) Using an improper power adapter will make the printing quality worse and even damage the printer. (3) Do not connect the telephone line to the cash box interface, otherwise the printer and telephone may be damaged.
VI. The Switch, Key and Indicator Light of Printer 8.1 Power Switch The power switch controls the flow of power to the printer. RP325\RP326\RP327 : When the is pressed, the printers muted on; When the "O" of the switch is pressed, the printer is fumed off. RP326 : Long press the power button to tum on the printer, long press the power button to turn off the printer after power on. A Attention: Make sure the power supply is connected before turning on the printer. 6.
6.3 Selim-Tost of Printer Self-test can detect whether the printer is working normally. If the Self-test list sample can be printed correctly, it indicates that everything is normal except the connection interface with the host computer, otherwise overhaul is required. In the self-test, it will print the software version number, print density, interface type, English characters and some Chinese characters In sequence.
(3) If there are multiple external Bluetooth device, select the printer corresponding to BDA address (ses self-test page for details). (4) Enter the initial password or "1234". (5) Complete the pairing. Please refer to the Bluetooth function description of the main device for the specific pairing method. When pairing, the RP32X series thermal receipt printer with Bluetooth interface must be on.
VII. Serial Interfaces of Printers The serial interface of RP32X series thermal receipt printer adopts RS-232 standard. The communication baud rate Is 9600bps, 19200bps, 38400bps or 115200bps optional (adjusting via DIP switch). It is parity-free, 8-bit data bit, 1-bit stop bit; RESTRICTS and XON/XOFF handshake protocols are supported. The functions of each pin of the printer serial interface gre defined as follows: Innumerate Mods! Signal source Description 2 TXD Printer The printer sends data to the host.
VIII. Parallel Interfaces of Printers The parallel interface socket of the RP32X series thermal receipt printer is a PIPPIN parallel socket with 8-bit parallel transmission, it supports Bushwhack handshake protocol (subject to the actual object).
IX.
X. Ethernet Interfaces of Printers The Ethernet Interface socket of thermal receipt printer Is standard RJ45-8P, it supports 10M/100M network, and the transmission speed is adaptive.
XI. Cash box Interfaces of Printers The cash box interface of the printer adopts JR-11 standard, 6-wire socket, and outputs DC 24V/1A power signal to drive the cash box. Insert the JR-11 crystal connector of the cash box Intel the cash box Interface to open the cash box through the printer.
XII. Cleaning the Printer 42.1 Cleaning the Printer Head Clean the print head when one of the following conditions occurs to the printer: {1} Printing is not clear; (2) A vertical column of the printed page is not clear; (3) The paper feeding noise is high. The print head cleaning steps are as follows: (1) Disconnect the power cord, open the upper cover and remove the paper if exists.
42.3 Cleaning the Printing Rubber Seller When one of the following conditions occurs to the printer, the printing rubber roller should be cleaned: (1) Printing is not clear; (2) A vertical column of the printed page Is not clear; (3) The paper feeding noise is high.
Xii. Release the Jammed Knife When the knife of printer is jammed, the upper cover of the printer cannot be opened. The printer shall be powered off and restarted. If the jammed knife is not reset, the power supply of the printer shall be turned off, the front cover of the printer (as shown in the left figure) is opened, and the jammed knife can be released by reversing the gear. {The gear is in the position us shown in the following figure} XVII.
XV. Driver Installation There are two ways to drive the thermal receipt printer, one is to install the driver directly under Windows 9X/7/8/10/ME/2000/XP/Linux/MAC, the other is to use the port for direct driving. 48.1 Installation for Windows Add the printer to Windows and assign the driver files in the driver disk to Windows. You can start printing only by calling the print command in the program. In this way, the printer driver of Windows actually converts characters into graphic dot matrix for printing.
XVI. FCC WARNING Any Changes expressly or modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: {1)This device may not cause harmful interference, device must accept any Interference raveled, Including Interference that may cause undesired operation.