PROTEKTOR II TM Long Range Wireless System VERSION I PROGRAMMING MANUAL ISSUE: 033 DATED: January 2014
" ! ! # $ % ! # " $ ! !!$! !% !!$! " & ! ! $ $ $ $ $ ! ! ! & " ! " " " " # # %
' $ ! " ! ! ( ) ! ) * & + ! %
The Protektor II Wireless System uses the latest wireless technology and techniques using a high frequency network with long range wireless signaling. The Protektor II system offers to the user the benefit of a number of functions not normally available when using wireless as the communication medium. (a) Each Zone Protektor area “Node” looks after it’s local zone, continually checking for alarm calls and/or detected fault monitoring signals from within its zone.
! "# $ %& '! $ "
( ) * " "+ The Network should be planned based on site surveys to determine the ideal placement for Zone Protektor Units. This will affect the programming of all components in the system; so proper planning is strongly suggested to reduce troubleshooting after installation. The diagram below provides a basic guide to typical Protektor network layout and High Frequency “zoning” arrangements.
+ "+ It is recommended that all system equipment should be pre-programmed at tabletop and labeled while completing a record sheet. A sample format is on next page, and Excel template can be provided by Rondish upon request. This record should be provided to the system technical service and maintenance provider after completion of commissioning and hand-over of the system to the user/operator. This programming record is vital for troubleshooting.
-, *&- ! 36>-,= -2?1. 00*&11 3 4 *&- 3 4 " 3:143 -2?1. *&1&.6& *&- 3 4 8-'6, ',& 1&''<.=1 ). ',& *)0 52& 3 4 ! *&- ! -, 9/:3 /,3 6/61-2;7< &'()*+ ! ,-..&/ 00*&11 )2 00*&11 : &'()*+ ! -.0 ,-..&/ ); -// 6)82).&.'1 !3 4 -, /99 -1267 ! -, -23 ,-63=6-,7 )2 00 /763, /,3 6/61-28 &'()*+ ! ,-..&/ 00*&11 ! *&- ! )2 00 -1'&* -*& '-'<). 276/99/61-2 -7161-2 *)72 &1&' 3 4 ))8 52& 3 4 00*&11 3 4 -// 52& 3"4 &0 789&* 3 )2 00 4 , - # .
, ) ) / PROTEKTOR CARE STATION FRONT PANEL VIEW Caregiver Key Acknowledge Key Alarm Call on (C-Key) Point (A-Key) LED indicator REAR PANEL VIEW Rotary switch (0-9) For setting “Area Serial Output Communication Port Code” >
, 0 "1+! " To enter the System Configuration menu, apply and simultaneously hold the Caregiver Key (C-Key) and Acknowledge button (A-Key). The C-Key and A-Key will be used to select and navigate through the menu. When navigating the Care Station menu, use the A-Key to cycle through the options, and C-Key to confirm the choice. 1. Check RF Channel 2. 3. 4. 5. Network Global Settings Slave Monitor Zone Protektor 6. Factory Default , 0 . -2 .
, 0 2 There are 3/4 parameters to be programmed: 1. Network ID Choose either “0” or “OFF”. Adjusting this setting to OFF will deactivate the high frequency (916MHz) Zone Protector wireless network and turn on the low frequency (433MHz) receiver inside the console for local operation only. 2. Care Station address This is the Master Care Station address (target code) in the network, where the setting of is factory default and is “48” in the network.
Master Care Station and Zone Protektor Configuration: , ,0 )& % & "+ 1. Room Type Setting Each call point is programmable to show various types of locations. Adjusting the BAT code on the Master Care Station will change the default room type for call points in the system. “BAT” = Building Area Type. There are 6 options - Use the A-Key to choose the desired setting: < 1: Room > < 2: Flat > < 3: Ward > < 4: Home > < 5: Apt > < 6: Area > 2.
It can be set to < 0: Printer > or < 1: Pager-TX125 >. Choose “Printer” if you will record alarms with a Dot Matrix printer or Rondish software database. Choose “Pager” if using a TX125 transmitter to directly signal POCSAG pagers. , 30 & " Up to 9 Slave Care Stations may be operated from the Master Care Station. Slave Monitor/s can be set as “enabled”, or “disabled” here. These can be configured to display alarms only in a particular Area/Site.
, 50 - ( 1 !& This section will return the Care Station to factory default settings, and display the current software version installed. , 60 7 # A facility will often want a nurse station to only see alarms from the same floor, local area, or ward. Using different area code settings will allow a Slave Monitor to display only local events. The area code is adjusted by the rotary switch at rear panel shown in the picture on page 7, and can be adjusted with a small screwdriver.
