AUTOMATE Interior Sun Sensor 433 MHz Internal sun sensor for automatic shade control. FEATURES: • 3 Modes of operation: - Close Mode - Open / Close Mode INSTR. MTRF-SUNSENS V1.
CONTENTS 1 TECHNICAL DATA / PACK CONTENTS 3 2 SAFETY 4 3 INSTALLATION 5 3.1 Sensor battery 5 3.2 Replacing battery 5 3.3 Mounting 5 4 6 FUNCTIONAL OVERVIEW 4.1 Buttons 6 4.2 Modes 6 4.3 View and change sensor mode 7 4.4 Light levels of light intensity values 7 4.5 Light intensity detection 7 4.6 Low battery notification 7 4.7 UP button 7 5 8 PROGRAMMING 5.1 Protocol selection 8 6 9 ADDING OR REMOVING SENSOR & CREATING GROUP CONTROL 6.1 Using Motor P1 Button 9 6.
1 TECHNICAL DATA / PACK CONTENTS TECHNICAL SPECIFICATIONS Voltage: Standby Current: 3V (CR2032) 5uA Frequency: 433.
2 SAFETY WARNING: Important safety instructions to be read before installation and use. Incorrect installation or use can lead to serious injury and will void manufacturer’s liability and warranty. It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference. • Do not expose to water, moisture, humid and damp environments or extreme temperatures.
3 INSTALLATION 3.1 Sensor battery Pull battery tab out to activate for first use. 3.2 Replacing battery Pry open using flat head screw driver where notches meet on the sensor. Remove old battery by pressing up from under the batterys position. Push new battery in with the “+” facing outwards. Replace cover by aligning notches and press together. 3.3 Mounting 1. Ensure surface on glass is clean and free of dust. 2. On the back of the sensor, peel clear plastic off to reveal adhesive. 3.
4 FUNCTIONAL OVERVIEW 4.1 Buttons Light Level Indicator Up Change Light Level P2 4.
4.3 View and change sensor mode To view the current mode, press the SUN button for one second 1 blink indicates mode 1 2 blinks indicate mode 2 3 blinks indicate mode 3 To change the mode: Hold the SUN button until the LED blinks 5 times. The mode has now shifted up by one. E.g. Mode 2 has changed to Mode 3. 4.
5 PROGRAMMING IMPORTANT Please refer to the relevant documentation of your motor model for instructions on adjusting motor settings. 5.1 Protocol selection This device can be configured to operate Acmeda line “EL” motors. (The default mode is ARC protocol). To toggle between ARC & EL modes follow the following steps. HOLD P2 whilst inserting battery To check which mode the sensor is currently in, press the UP or P2 button briefly.
6 ADDING OR REMOVING SENSOR & CREATING GROUP CONTROL 6.1 Using Motor P1 Button Hold P1 button on motor head. Hold P2 on sensor to add or remove. Motor Response 6.2 Motor Response Using a pre-existing Controller Press P2 on existing controller. Motor Response Press P2 on existing controller. Motor Response Press P2 on new sensor. Motor Response IMPORTANT Consult user manual for your controller or sensor.
7 TROUBLESHOOTING Problem Cause Remedy Sensor battery is discharged Replace battery (Ref. Section 3.2) Battery is inserted incorrectly Motor is not responding Check battery polarity (Ref. Section 3.2) Radio interference / Shielding Ensure remote is positioned away from metal objects and that aerial on motor or reciever is kept straight and away from metal.
8 NOTES ROLLEASE ACMEDA Automate Programming Instructions | Interior Sun Sensor | 11
ROLLEASE ACMEDA AUSTRALIA 110 Northcorp Boulevard, Broadmeadows VIC 3047 T +61 3 9355 0100 | F +61 3 9355 0110 Western Australia Branch Unit 1, 41 Mulgul Road, Malaga WA 6090 T +61 8 9248 5571 | F +61 8 9248 5572 ROLLEASE ACMEDA USA 200 Harvard Avenue Stamford, CT 06902 6320 T +1 203 964 1573 | F +1 203 964 0513 ROLLEASE ACMEDA EUROPE Via Conca Del Naviglio 18, Milan (Lombardia) Italy T +39 02 8982 7317 | F +39 02 8982 7317 info@rolleaseacmeda.com rolleaseacmeda.