AUTOMATE Paradigm Remote Control LEVEL CONTROL TOUCH SENSITIVE 433 MHz AUTOMATE | Paradigm remotes feature a contemporary design with touch sensivite controls. Available in single and fifteen channel models, Paradigm remotes are compatible with all ARC motors. FEATURES: • Available in single channel & Fifteen Channel. • Touch sensitive buttons. • Levelling control (15 channel remote). • LCD display (15 Channel remote). • Hide unused channel function. INSTR-MTRF-REM V1.
CONTENTS 1 TECHNICAL DATA / PACK CONTENTS 3 2 SAFETY 4 3 INSTALLATION 5 3.1 Wall mount holder 5 3.2 Remote battery 5 4 6 FUNCTIONAL OVERVIEW 4.1 Buttons 6 4.2 Levelling control 6 4.3 Selecting a channel - (multi channel remote) 7 4.4 Group control using CH “0” 7 5 8 PROGRAMMING 5.1 Protocol selection 8 5.2 Hide unused channels 9 5.3 Disable limit setting function of remote 9 6 ADDING OR REMOVING CONTROLLERS & CREATING GROUP CHANNELS 10 6.1 Using Motor P1 Button 10 6.
1 TECHNICAL DATA / PACK CONTENTS TECHNICAL SPECIFICATIONS Voltage: 3V (CR2450) Frequency: 433.92 MHz Transmitting Power: 10 milliwatt Ambient Operating Temperature: -10°C -50°C Transmission Distance: up to 200 meters (open space) PACK CONTENTS 1 x remote (Single or Fifteen Channel) 1 x magnetic holder inc.
2 SAFETY WARNING: Important safety instructions to be read before installation and use. Incorrect installation or use can lead to serious injury and will void manufacturer’s liability and warranty. It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference. • Do not expose to water, moisture, humid and damp environments or extreme temperatures.
3 INSTALLATION 3.1 Wall mount holder Remove cover from base by prying with flat head screwdriver. Use supplied fasteners and anchors to attach the base to wall. Replace cover by pressing snap latches into place. 3.2 Remote battery Remove cover from remote press gently in and down to disengage cover. Install battery with positive (+) side facing up. Slide to remove.
4 FUNCTIONAL OVERVIEW 4.1 Buttons UP STOP LEVEL CONTROL DOWN CHANNEL SETTING (P2) 4.2 Levelling control The levelling control bar can be used to visualize and accurately set your preferred shade position. When used to control a group of shades, they will all perfectly align to the same position. .
4.3 Selecting a channel - (multi channel remote) Hold CH button. Within 4 seconds press UP or DOWN to select desired channel . Press CH or STOP to confirm Response LCD screen will begin to flash IMPORTANT If no button is pressed within 4 seconds, the channel selection will automatically be confirmed 4.4 Group control using CH “0” Channel "0" is pre-set to controll ALL shades paired within your multi-channel remote.
5 PROGRAMMING IMPORTANT Please refer to the the relevant documentation of your motor model for instructions on adjusting motor settings. 5.1 Protocol selection This device can be configured to operate Acmeda line “EL” motors. (The default mode is ARC protocol). To toggle between ARC & EL modes follow the following steps.
5.2 Hide unused channels Your multi channel remote can be configured to have anywhere between 1 or 15 visible channels. Inactive channels will not be visible when scrolling through the CH selection. Hold STOP and CH Continue holding CH and select required channel qty by pressing UP or DOWN Press STOP to confirm Response Response Channel 15 flashes Flashing stops 5.3 Disable limit setting function of remote IMPORTANT This mode is intended to be used after all shade programming is completed.
6 ADDING OR REMOVING CONTROLLERS & CREATING GROUP CHANNELS 6.1 Using Motor P1 Button Hold P1 button on motor head. Hold STOP on controller to add or remove. Motor Response 6.2 Motor Response Using a pre-existing Controller Press P2 on existing controller. Motor Response Press P2 on existing controller. Motor Response Press P2 on new controller. Motor Response IMPORTANT Consult user manual for your controller or sensor.
7 TROUBLESHOOTING Problem Motor is not responding Cause Remedy Remote battery is discharged Replace battery Battery is inserted incorrectly Check battery polarity Radio interference / Shielding Ensure remote is positioned away from metal objects and that aerial on motor or reciever is kept straight and away from metal.
ROLLEASE ACMEDA AUSTRALIA 110 Northcorp Boulevard, Broadmeadows VIC 3047 T +61 3 9355 0100 | F +61 3 9355 0110 Western Australia Branch Unit 1, 41 Mulgul Road, Malaga WA 6090 T +61 8 9248 5571 | F +61 8 9248 5572 ROLLEASE ACMEDA USA 200 Harvard Avenue Stamford, CT 06902 6320 T +1 203 964 1573 | F +1 203 964 0513 ROLLEASE ACMEDA EUROPE Via Conca Del Naviglio 18, Milan (Lombardia) Italy T +39 02 8982 7317 | F +39 02 8982 7317 info@rolleaseacmeda.com rolleaseacmeda.