Assembly Manual

ManualsBrandsRollease Acmeda ManualsElectronicsAUTOMATE PUSH5 REMOTE

1. ASSEMBLY 3. PRODUCT RANGE (cont.)

Please refer to separate Rollease Acmeda System Assembly

Manual for full assembly instructions relevant to the

hardware system being used.

2. BATTERY MANAGEMENT

For battery motors;

Prevent discharging the battery completely for extended

periods, recharge as soon as the battery is discharged

Before first use please charge motor for 6 hours, using the

recommended AC charger

During operation, if battery is low,

the motor will beep 10 times to

prompt the user it needs charging.

CHARGING NOTES

PRODUCT

RANGE

(co

nt.)

The Quick Start Programming Guide is universal for all

Automate Motors including:

Note: Curtain motor does not

Jog but instead LED flashes

Internal Tubular

Large Tubular

0.6 Cord Lift

0.8 Cord Lift

Curtain

Tilt Motor

3. PRODUCT RANGE

Hold P1

P1 GREEN

Internal Tubular

Large Tubular

0.6 Cord Lift

0.8 Cord Lift

Curtain

Tilt Motor

For battery motors ensure the motor is fully charged as

per instructions.

CHARGE 100%

Use a spare remote to individually program each shade.

Then use that remote to group rooms as per the user’s

needs. If you go back and service the installation later

then, that same remote can be used to check the

individual shades.

Do not dispose of in

general waste.

Incorrect installation or use can lead to serious injury and

will void manufacturer’s liability and warranty. It is

important for the safety of persons to follow the enclosed

instructions. Save these instructions for future reference.

This device complies with Part 15 of the FCC Rules /

Innovation, Science and Economic Development Canada’s

licence-exempt RSS(s).

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference.

(2) this device must accept any interference received,

including interference that may cause undesired

operation.

L’émetteur/récepteur exempt de licence contenu dans

le présent appareil est conforme aux CNR d’Innovation,

Sciences et Développement économique Canada

applicables aux appareils radio exempts

de licence.

L’exploitation est autorisée aux deux conditions

suivantes : 1. L’appareil ne doit pas produire de

brouillage; 2. L’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est

susceptible d’en compromettre le fonctionnement.

Changes or modifications not expressly approved by the

party responsible for compliance could void the user's

authority to operate the equipment.

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation. This equipment

generates uses and can radiate radio frequency energy

and, if not installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful

interference to radio or television reception, which can

be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by

one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

• Do not expose to water,moisture, humid and damp

environments or extreme temperatures.

• Persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and

knowledge, should not be allowed to use this product.

• Use or modification outside the scope of this instruction

manual will void warranty.

• Installation and programming to be performed by a

suitably qualified installer.

• Follow installation instructions.

• For use with motorized shading devices.

• Keep away from children.

• Frequently inspect for improper operation.

Do not use if repair or adjustment is necessary.

• Keep clear when in operation.

• Replace battery with correctly specified type.

WARNING: Important safety instructions to be read

before installation and use.

INSTALLERS REMOTE

Run the fabric up and down several times to ensure fabric

has settled to some extent and re adjust the limits if needed.

SETTLE FABRIC

If pre-programmed: before shipping the motor ensure

the motor is put into sleep mode so it doesn’t activate

during transit.

SLEEP MODE

Prevent users accidently changing the limit;

ensure the remote is locked as your last step of programming.

LOCK REMOTE

Ask the customer the day before to think how shades will be

zoned on the remote. This may save an extra call out.

ZONE / GROUPS

INSTALLER

BEST PRACTICE AND TIPS

DISPOSAL AND RECYCLING

P1 LOCATIONS

SAFETY

CAUTION

INSTALLER

QUICK START PROGRAMMING

This setup wizard should be used for new installation or factory reset motors only.

Individual steps may not work if you haven't followed the wizard from the beginning.

Select a single or multiple channels by

toggling channels as required.

Note the corresponding LED next to each

channel.

REMOTE

STEP 1

SECS

BEEP

JOG

* Internal Tubular

pictured.

Refer to “P1 Locations”

for specific devices

REMOTE

Within 4 seconds hold the stop button on the

remote for 3 seconds.

The motor will respond with Jog and Beep

Press the P1 button on the motor for

2 Seconds until the motor responds as

below

STEP 2

MOTOR RESPONSE

BEEP

JOG

MOTOR RESPONSE

JOG

MOTOR RESPONSE

Press up or down to check the motor

direction. If correct skip to step 5.

CHECK

DIRECTION

STEP 3

SECS

If the shade direction needs to be reversed;

press and hold the up & down arrow together

for 5 seconds until the motor Jogs.

Reversing motor direction using this method is only

possible during initial set-up.

CHANGE

DIRECTION

STEP 4

SET

UPPER LIMIT

Tap the arrow several times or hold down if

needed; press arrow to stop.

Move shade to desired top limit by

pressing the up arrow repeatedly.

Then press and hold up & stop together

for 5 sec to save limit.

STEP 5

SECS5

BEEP

JOG

MOTOR RESPONSE

SET

BOTTOM LIMIT

Tap the arrow several times or hold down if

needed; press arrow to stop.

Move shade to desired bottom limit by

pressing the down arrow repeatedly.

Then press and hold down & stop

together for 5 sec to save limit.

STEP 6

SECS5

SECS

Repeat steps 1-6 for all motors.

Once complete Press and hold the Lock

button for 6 seconds while looking at the

LED, and hold until solid.

SAVE

YOUR LIMIT

STEP 7

BEEP

SECS

SECS2 SECS6 SECS10 SECS14

To reset all settings in the motor press

and hold the P1 Button for 14 seconds,

you should see 4 independent jogs

followed by 4x Beeps at the end.

* Internal Tubular pictured above.

Refer to “P1 Locations” for specific devices

FACTORY RESET

MOTOR RESET PROCEDURE

MOTOR RESPONSE

Programming

Guide

Automate Motor

Summary of content (2 pages)

PAGE 1
3. PRODUCT RANGE (cont.) 1. ASSEMBLY Please refer to separate Rollease Acmeda System Assemblyy Manual for full assembly instructions relevant to the hardware system being used. CAUTION This device complies with Part 15 of the FCC Rules / Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference.
PAGE 2
REPLACE BATTERY CHANNEL DOWN BUTTON STOP BUTTON UP BUTTON BUTTON OVERVIEW GROUP CONTROL WALL MOUNTING Channel "ALL" is pre-set to control ALL shades paired to your Muli-channel remote. Replace cover by pressing snap latches into place. Remove cover from remote; unscrew with screw driver then firmly press down and slide left. LOCK SETTING (P2) Install battery CR2430 with positive (+) side facing up.