Safety Instructions
SAFETY NOTE
1, This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge
if they have been given supervision or instruction
concerning use of the appliance in a safe way and
understand the hazards involved.
2, Children shall not play with the appliance.
3, Cleaning and user maintenance shall not be made by
children without supervision.
4, If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
5, WARNING: the drive shall be disconnected from its
power source during cleaning, maintenance and when
replacing parts.
6, The instructions shall state that the A-weighted emis
sion sound pressure level of the drive is equal to or less
than 70 dB(A), e.g. by writing LpA 70 dB(A).
7, The mass and the dimension of the driven part shall be
compatible with the rated torque and rated operating
time.
8, The type of driven part the drive is intended for.
9, WARNING: Important safety instructions. It is important
for the safety of persons to follow these instructions.
Save these instructions.
10, Do not allow children to play with fixed controls. Keep
remote controls away from children
11, Frequently examine the installation for imbalance and
signs of wear or damage to cables and springs. Do not
use if repair or adjustment is necessary
12, Watch the moving shutter and keep people away until
he shutter is completely closed
13, WARNING: Important safety instructions. Follow all
instructions, since incorrect installation can lead to
severe injury.
14, Before installing the drive, remove any unnecessary
cords and disable any equipment not needed for
powered operation
1. Not operating under low voltage motors:
When the power supply voltage is lower than 6.5V, the motor stops running, and it can not start until
the voltage exceeds 6.8V.
When the power supply voltage is lower than 7.2V, the motor runs continuously and the buzzer will
beep 10 times.
When the power supply voltage is lower than 6.2V, the motor stops the buzzer beeping, and the
voltage can be started only when the voltage is greater than 6.5V.
2. Operating
The valid interval of the emitter button is 10s,the emitter will quit the set after 10s;
The motor will run or beep for hint,please do the next step after the hint.
3. Set limit position
After the up/down limit position setting,and the up/down limit position can’t at the same position;
After limit setting,with power off and memory function;
Into the match-code status 2 minutes later, it will quit out the setting limits status automatically;
It will delete every memory and restore the factory settings.
4. When the motor running without any operation, the maximum running time is 6 minutes,it will stop
automatically.
5. If the emitter lost,please setting up again with new emitter.
Note: The left and right rotation of the hook controls the motor to reverse and the centering motor of the hook stops.
Operation note
Please read the following precautions before use:
Parameters(More models and parameters are subject to the nameplate)
Note: it can be used with hook controller and battery rod, or only with battery or adapter.
Product introduction
Connection mode
One motor maximum can store 10 channels,over 10 channels,if still need add
new channels,it will be repeating covered in turn from second channel.
Functional features：
Switch Direction
Built-in Receiver
Jog & Tilt
Preferred Stop Position
Low Power Consumption, Suitable
for External Battery Power
Electronic Limit
Stall Protection
Program Button
Solar Charging
Reset to Factor Mode
Unpair Single Emittert
Operating
temperature
MT01-4001-069001
0.6N.m
10RPM
8.4V
0.54A
5W
433.925MHz
Button specification
Motor setting
button(P1)
Solar panel
charging interface
Adapter charging
interface
Hook
Signal line
The battery bar
Type
Rated Torque(N.m)
Rated Voltage(V)
Rated Speed
(RPM)
Rated Current(A)
Rated Power(W)
Emission Frequency(MHz)
P2
M
P2
Lithium Cell
3V
P2
Up button
Stop button
Down button
Setting button
&
READING
(A-00)
0
45
FCC Warning:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
MODIFICATION: Any changes or modifications not expressly approved by the grantee of this device could
void the user’s authority to operate the device.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
IC ：
-English:
This device complies with Industry Canada RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference
,including interference that may cause undesired operation of the device.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
-French:
Leprésent appareil est conforme aux CNR d'Industrie Canada applicable aux appareils radio
Exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillag
e radioélectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement."l.
AUTOMATE | Core Tilt Motor
(Optional)
(Optional)